Engine JAC HFC4DA1-2C. Manual — part 170
BG
BG
BG
BG Body
Body
Body
Body Glass
Glass
Glass
Glass
- 13 -
Removal/Installation
Removal/Installation
Removal/Installation
Removal/Installation (Continued)
(Continued)
(Continued)
(Continued)
Front
Front
Front
Front door
door
door
door glass
glass
glass
glass regulator
regulator
regulator
regulator
5.
Remove the mounting screws for regulator motor.
6.
Take down the regulator motor.
Installation
Install it in reverse order of removal.
BG
BG
BG
BG Body
Body
Body
Body Glass
Glass
Glass
Glass
- 14 -
Removal/Installation
Removal/Installation
Removal/Installation
Removal/Installation
Left
Left
Left
Left side
side
side
side wall
wall
wall
wall glass
glass
glass
glass
Removal
1.
Prepare necessary tools.
2.
Peel off the window glass seal.
Note:
Note:
Note:
Note:
Peel off the window glass seal completely from top to
bottom as shown in the figure.
3.
Remove upper and lower guard plates of B-pillar.
4.
Remove upper and lower guard plates of B-pillar.
BG
BG
BG
BG Body
Body
Body
Body Glass
Glass
Glass
Glass
- 15 -
Removal/Installation
Removal/Installation
Removal/Installation
Removal/Installation (Continued)
(Continued)
(Continued)
(Continued)
Left
Left
Left
Left side
side
side
side wall
wall
wall
wall glass
glass
glass
glass
5.
Install the precise cutting blade (24mm hook type
blade) onto the cutter.
Warning:
Warning:
Warning:
Warning:
When using tools for cutting glasses, please wear gloves
and goggles to avoid possible injury caused by
glass fragments generated during cutting.
Attention:
Attention:
Attention:
Attention:
In case of the windshield to be reused, it is prohibited
to use cutter or electric cutting tools.
6.
Remove the front door window seal.
Note:
Note:
Note:
Note:
Peel off the window glass seal completely from top
to bottom as shown in the figure.
7.
Cut the glass sealant, as shown in the figure.
Note:
Note:
Note:
Note:
Two persons are necessary for removal of glass and
one should stand outside to hold the glass by
using suction cup.
BG
BG
BG
BG Body
Body
Body
Body Glass
Glass
Glass
Glass
- 16 -
Removal/Installation
Removal/Installation
Removal/Installation
Removal/Installation
Left
Left
Left
Left side
side
side
side wall
wall
wall
wall glass
glass
glass
glass
Installation
1.
Prepare repair kit, with the following articles
included:
Sea
lant (carbamic acid
ethyl ester adhesive)
Cleaner
Primer
Cloth
Wool brush
Felt
Mat
Nozzle
Note:
Note:
Note:
Note: An additional tube of sealant may be applied.
Note:
Note:
Note:
Note:
Peel off the window glass seal completely from top
to bottom as shown in the figure.
Note:
Note:
Note:
Note:
Don’t
contact
the
already
trimmed
surface,
otherwise, bonding effect of new sealant may be
influenced.
2.
Trim the side grooves.
�
Install the precise cutting blade.
Trim the polyurethane sealant remained on grooves
carefully, with polyurethane sealant in thickness of 1mm
left on the body for side trimming.
3.
Wipe the glass clean.
Trim the polyurethane sealant remained on window
carefully, with polyurethane sealant in thickness of
1mm left on the glass for side trimming.
Caution:
Caution:
Caution:
Caution:
Glass primer contains solvent that can make the primer
hardened after volatilization but also can soften the
surface
coat of
synthetic
paint;
therefore,
“ZK”
polypropylene surface paint mixed with hardener should
be applied around the window.
4.
Install the glass.
�
Mount the glass in place with center aligned.
�
Adjust glass based on window groove height to
ensure proper alignment. Adjust when necessary.
�
Press the glass tightly into the sealant from center
part gradually to both sides.
Note:
Note:
Note:
Note:
Park the vehicle in the place with ambient temperature
of zero degree and don’t drive it 24h before complete
curing of carbamic acid ethyl ester adhesive. The curing
time is determined by temperature and humidity, which
shall be prolonged in case of low temperature and
humidity.
5.
Install remaining parts in reverse order of removal.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст