JAC S2. Elctrical Wiring diagrams — part 8
Combination Switch, Alternation Switch
Combination Switch, Alternation Switch
104
VI、Rearview Mirror Regulating Switch
(I)Removal
1. Open engine cabin cover
2. Disconnect battery negative electrode Refer to “Disconnection and connection of battery electrode”
3. Remove left front door threshold guard panel assembly Refer to “Left front door threshold guard panel assembly”
4. Remove left front side vehicle door frame rubber strip Refer to “Vehicle door frame rubber strip”
5. Remove lower trim panel of A pillar Refer to “Lower trim panel of A pillar”
6. Remove dashboard left end cover Refer to “Dashboard left end cover”
7. Remove lower guard panel assembly of driver’s side Refer to “Lower guard panel assembly of driver’s side”
8. Remove rearview regulating switch
1). Disconnect jack catch of rearview regulating switch and
lower guard panel assembly of driver’s side, and take
down rearview regulating switch from behind side;
(II)Installation
1. Install rearview regulating switch
1). Install rearview regulating switch from behind side, and
ensure jack catch is connected in place;
2. Install lower guard panel assembly of driver’s side
3. Install dashboard left end cover
4. Install lower trim panel of A pillar
5. Install left front side vehicle door frame rubber strip
6. Install left front door threshold guard panel assembly
7. Connect battery negative electrode
8. Close engine cabin cover
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Combination Switch, Alternation Switch
Combination Switch, Alternation Switch
105
VII、Window Regulator Main Control Switch Assembly
(I)Removal
1. Open engine cabin cover
2. Disconnect battery negative electrode Refer to “Disconnection and connection of battery electrode”
3. Remove left front door inclined handle Refer to “Front door inclined handle”
4. Remove left front door handle Refer to “Right door handle”
5. Remove window regulator main control switch assembly
1). Pry 6 buckles of window regulator main control switch
assembly, disconnect connection of window regulator
main control switch assembly and switch panel, and take
down window regulator main control switch assembly;
(II)Installation
1. Install window regulator main control switch assembly
1). Install window regulator main control switch assembly to
left front door switch panel, and ensure to be installed in
place;
△ Note Check whether all buttons function are normal after
installing. If not or can’t work, please re-install or
replace.
2. Install left front door handle
3. Install left front door inclined handle
4. Connect battery negative electrode
5. Close engine cabin cover
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Combination Switch, Alternation Switch
Combination Switch, Alternation Switch
106
VIII、Window Regulator Switch
(I)Removal
1. Open engine cabin cover
2. Disconnect battery negative electrode Refer to “Disconnection and connection of battery electrode”
3. Remove right front door inclined handle Refer to “Front door inclined handle”
4. Remove right front door handle Refer to “Right door handle”
5. Remove window regulator switch
1). Remove 2 fixed bolts of window regulator switch;
2). Take down window regulator switch;
(II)Installation
1. Install window regulator switch
1). Place window regulator switch to installation position, and
tighten 2 fixed bolts of window regulator switch;
2. Install right front door handle
3. Install right front door inclined handle
4. Connect battery negative electrode
5. Close engine cabin cover
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Combination Switch, Alternation Switch
Combination Switch, Alternation Switch
107
IX、Tail Door Switch Assembly
(I)Removal
1. Open rear tail door
2. Open engine cabin cover
3. Disconnect battery negative electrode Refer to “Disconnection and connection of battery electrode”
4. Remove tail door trim panel assembly Refer to “Tail door trim panel assembly”
5. Remove tail door switch assembly
1). Disconnect wiring harness connector ① of tail door switch;
2). Remove fixed bracket ② of tail door switch assembly;
3). Take down tail door switch assembly from outside vehicle;
(II)Installation
1. Install tail door switch assembly
1). Place tail door switch assembly to installation hole, and install
fixed bracket ② of tail door switch assembly;
2). Connect wiring harness connector ① of tail door switch
assembly;
2. Install tail door trim panel assembly
3. Close rear tail door
4. Connect battery negative electrode
5. Close engine cabin cover
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Combination Switch, Alternation Switch
Combination Switch, Alternation Switch
108
X、Warning Light Switch
(I)Removal
1. Open engine cabin cover
2. Disconnect battery negative electrode Refer to “Disconnection and connection of battery electrode”
3. Remove central right side trim panel assembly Refer to “Central right side trim panel assembly”
4. Remove warning light switch
1). Disconnect jack catch of warning light switch and central
right side trim panel assembly, and take down warning
light switch from front side;
(II)Installation
1. Install warning light switch
1). Install warning light switch from front side, and ensure jack
catch is installed in place;
2. Install central right side trim panel assembly
3. Connect battery negative electrode
4. Close engine cabin cover
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Combination Switch, Alternation Switch
Combination Switch, Alternation Switch
109
XI、Headlight Height Regulating Switch
(I)Removal
1. Open engine cabin cover
2. Disconnect battery negative electrode Refer to “Disconnection and connection of battery electrode”
3. Remove left front door threshold guard panel assembly Refer to “Left front door threshold guard panel assembly”
4. Remove left front side vehicle door frame rubber strip Refer to “Vehicle door frame rubber strip”
5. Remove lower trim panel of A pillar Refer to “Lower trim panel of A pillar”
6. Remove dashboard left end cover Refer to “Dashboard left end cover”
7. Remove lower guard panel assembly of driver’s side Refer to “Lower guard panel assembly of driver’s side”
8. Remove headlight height regulating switch
1). Disconnect jack catch of headlight height regulating switch
and lower guard panel assembly of driver’s side, and
take down headlight height regulating switch from front
side;
(II)Installation
1. Install headlight height regulating switch
1). Install headlight height regulating switch in front, and
ensure jack catch is connected in place;
2. Install lower guard panel assembly of driver’s side
3. Install dashboard left end cover
4. Install lower trim panel of A pillar
5. Install left front side vehicle door frame rubber strip
6. Install left front door threshold guard panel assembly
7. Connect battery negative electrode
8. Close engine cabin cover
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Combination Switch, Alternation Switch
Combination Switch, Alternation Switch
110
XII、Light Regulating Switch
(I)Removal
1. Open engine cabin cover
2. Disconnect battery negative electrode Refer to “Disconnection and connection of battery electrode”
3. Remove left front door threshold guard panel assembly Refer to “Left front door threshold guard panel assembly”
4. Remove left front side vehicle door frame rubber strip Refer to “Vehicle door frame rubber strip”
5. Remove lower trim panel of A pillar Refer to “Lower trim panel of A pillar”
6. Remove dashboard left end cover Refer to “Dashboard left end cover”
7. Remove lower guard panel assembly of driver’s side Refer to “Lower guard panel assembly of driver’s side”
8. Remove light regulating switch
1). Disconnect jack catch of light regulating switch and lower
guard panel assembly of driver’s side, and take down
light regulating switch;
(II)Installation
1. Install light regulating switch
1). Install light regulating switch in front, and ensure jack catch
is connected in place;
2. Install lower guard panel assembly of driver’s side
3. Install dashboard left end cover
4. Install lower trim panel of A pillar
5. Install left front side vehicle door frame rubber strip
6. Install left front door threshold guard panel assembly
7. Connect battery negative electrode
8. Close engine cabin cover
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Combination Switch, Alternation Switch
Combination Switch, Alternation Switch
111
XIII、Door Contact Switch
(I)Removal
1. Open engine cabin cover
2. Disconnect battery negative electrode
3. Remove door contact switch
1). Remove fixed bolt of door contact switch;
2). Disconnect wiring harness connector of door contact
switch, and take down door contact switch;
(II)Installation
1. Install door contact switch
1). Connect wiring harness connector of door contact switch,
and place door contact switch to installation position
hole;
2). Tighten fixed bolt of door contact switch;
Tighten torque
9~11N·m
2. Connect battery negative electrode
3. Close engine cabin cover
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Combination Switch, Alternation Switch
Combination Switch, Alternation Switch
112
XIV、ESP Switch
(I)Removal
1. Open engine cabin cover
2. Disconnect battery negative electrode Refer to “Disconnection and connection of battery electrode”
3. Remove left front door threshold guard panel assembly Refer to “Left front door threshold guard panel assembly”
4. Remove left front side vehicle door frame rubber strip Refer to “Vehicle door frame rubber strip”
5. Remove lower trim panel of A pillar Refer to “Lower trim panel of A pillar”
6. Remove dashboard left end cover Refer to “Dashboard left end cover”
7. Remove lower guard panel assembly of driver’s side Refer to “Lower guard panel assembly of driver’s side”
8. Remove ESP switch
1). Disconnect jack catch of ESP switch and lower guard panel
assembly of driver’s side, and take down ESP switch;
(II)Installation
1. Install ESP switch
1). Install ESP switch in front, and ensure jack catch is
connected in place.
2. Install lower guard panel assembly of driver’s side
3. Install dashboard left end cover
4. Install lower trim panel of A pillar
5. Install left front side vehicle door frame rubber strip
6. Install left front door threshold guard panel assembly
7. Connect battery negative electrode
8. Close engine cabin cover
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Illumination System
Illumination System
113
Illumination System
I、Summary
(I)Structure Overview
Interior illumination component position figure
1. Front top light
2. Trunk light
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Illumination System
Illumination System
114
Exterior illumination component position figure
1. Left front fog light 10. Left rear tail door combination light
2. Left daylight driving light 11. Left rear side wall combination light
3. Left front combination light 12.Left reversing light
4. Right front fog light 13.Right rear reflector
5. Right daylight driving light 14. Right reversing light
6. Right front combination light 15. License plate light
7. Right rear side wall combination light 16. Rear fog light
8. Right rear tail door combination light 17. Left rear reflector
9. High position brake light
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Illumination System
Illumination System
115
(II)Operation Principle
Electrical schematic diagram (vehicle type without CAN)
Front
headlight
regulating
motor
Front headlight
regulating switch
Low beam
light relay
Low beam
light
High beam
light relay
High beam
light
Warning
light relay
Turning
light
Front
fog
light relay
C
om
bi
nat
ion m
et
er
Light
com
bi
nat
ion s
w
itch
Front
fog
light
Rear
fog
light relay
Rear
fog
light
Small light
relay
Small light
License
plate light
Brake light
switch
Brake light
Reversing
light
Interior top
light
Door light
Door control
switch
Generator
Daylight
driving relay
Daylight
driving
Backlight
light
Reversing
light switch
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Illumination System
Illumination System
116
Electrical schematic diagram (vehicle type with CAN)
(III)Technical Parameter
No.
Name
Light bulb type
Power
Light color
1
High beam light
H7
2×55W
White
2
Low beam light
H7
2×55W
White
3
Front turning light
PY21W
2×21W
Amber
4
Front position light
W5W
2×5W
White
5
Front fog light
H8
2×35W
White
6
Daylight driving light
LED
2×5.6W
White
7
Rear position light/Brake light
P21/5W
2×21W+2×5W
Red
8
Rear turning light
P21W
2×21W
Amber
9
Rear position light
W5W
2×5W
White
10
Rear fog light
LED
5.6W
Red
11
Reversing light
P21W
2×21W
White
Reversing
light switch
Reversing
light
Combination
meter
Generator
Door control
switch
Light combination
switch
Brake
light
switch
Warning light
switch
Daylight driving
light relay
Brake light
Small light
relay
Turning
light relay
Small light
License
plate light
Backlight
light
Daylight
driving light
Rear
fog
light relay
Rear
fog
light
Front
fog
light relay
Front
fog
light
High beam
light relay
High beam
light
Low beam
light relay
Low beam
light
Headlight
regulating switch
Headlight
regulating motor
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Illumination System
Illumination System
117
No.
Name
Light bulb type
Power
Light color
12
License plate light
W5W
2×5W
White
13
High position brake light
LED
1.7W
Red
14
Front top light
C10W
2×10W
White
15
Trunk light
KHA
5W
White
(IV)Torque Parameter
No.
Item
Torque (N·m)
1
Front combination light fixed bolt
3~5
2
Front fog light fixed bolt
1~3
3
Daylight driving light
1~3
(V)Maintenance Note
1. Must disconnect battery negative electrode and waiting for at least 1 min before removing electrical wiring harness connector,
or else it may damage vehicle.
2. When disassemble and assemble components, use cloth to protect disassembled components to prevent to be damaged.
3. When disassemble metal clips from trim, use cloth wrap screwdriver blade. Pay attention to not damage vehicle body
component.
4. When disassemble and assemble some components that one person can’t complete, need two person to operate to avoid drop.
5. Please don’t use too much power when disassemble some components, because it may cause component deformation.
6. Don’t let light bulb and rear cover disassemble too long time from light, because dust, moisture, fog etc. Entering into light
may infect light function. After disassemble light bulb in front combined light reflecting shade, please install new light bulb.
7. Light combination light is semi-closed type, and use replaceable halogen light bulb. Replacing light bulb can be operated in
engine cabin, but it’s better to replace after removing.
8. Don’t touch window casing, and only can handle plastic seat of light bulb when operating light bulb.
9. Don’t shake or turn light bulb when removing.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Illumination System
Illumination System
118
II、Troubleshooting
(I)Troubleshooting List
No. Fault phenomenon
Fault reason analysis
Solution
Remark
1
Front headlight, fog
light, small light,
turning light not
work
Light filament fused
Replace light bulb
Refer to light not
work(front
headlight,
fog
light, small light,
turning light)
Fuse fused
Replace fuse
Power supply not connected, wiring harness
connector loosen
Maintain circuit fault
Relay not work
Replace relay
Light switch not work
Replace light switch
Light switch circuit fault
Maintain light switch circuit fault
BCM fault
Replace BCM
2
Reversing light not
work
Reversing light fuse fused
Replace fuse
Refer to
reversing light
not work
Reversing switch installation incorrect
Adjust to install reversing light switch
Reversing switch damaged
Replace reversing light switch
Reversing light filament fused
Replace light bulb
3
Brake light not work
Brake light fuse fused
Replace brake light fuse
Refer to brake
light not work
Brake switch installation incorrect
Adjust to install brake switch
Brake switch damaged
Replace brake light switch
Brake light filament fused
Replace light bulb
(II)Illumination system fuse, relay, wiring harness connector list
No.
Light
Fuse
Relay
Wiring harness connector and PIN
1
Left low beam light
IF16 20A
IR03
E05-8
2
Right low beam light
E20-8
3
Left high beam light
IF17 15A
IR04
E05-10
4
Right high beam light
E20-10
5
Left front position light
IF04 10A
IR08
E05-7
6
Left rear position light
E09-6
7
Left rear inside position light
T12-1
8
Left license plate light
RB02-1
9
Right front position light
IF04 10A
E20-7
10
Right rear position light
F28-6
11
Right rear inside position light
T17-1
12
Right license plate light
RB05-1
13
Left front turning light
\
\
E05-2
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Illumination System
Illumination System
119
No.
Light
Fuse
Relay
Wiring harness connector and PIN
14
Left side turning light
D02-1
15
Left rear turning light
F09-4
16
Right front turning light
E20-2
17
Right side turning light
D11-1
18
Right rear turning light
F28-4
19
Reversing light
IF20 10A
\
RB01-1/RB08-1
20
Reversing light switch
C24
21
Left brake light
\
\
F09-5
22
Right brake light
F28-5
23
High position brake light
T01-1
24
Brake light switch
\
\
E11
25
Left front fog light
IF07 15A
IR10
E03-1
26
Right front fog light
E23-1
27
Rear fog light
IF38 10A
IR09
RB04-1
(III)Troubleshooting Flow Chart
Front headlight, fog light, turning light not working
Step
Detect content
Solution
Judging specification
Next step
Yes
No
1
Confirm
fault
phenomenon
Ignition switch at relevant
position, light switch turn to
relevant light position
Whether relevant light is on
Next step
Turn to step 3
2
Check
intermittent
fault
Check and deal with relevant
wiring harness connector
loosen condition
3
Check relevant light
fuse
Remove relevant light fuse
Whether fuse is fused
Replace fuse, turn
to next step
Turn to step 5
4
Check whether fault is
removed
after
replacing fuse
Turn Light switch to relevant
light position
Whether relevant light is on
Fault is removed
Next step
5
Check relevant light
bulb
Dismount light bulb, check
filament
Whether filament is fused
Replace relevant
light bulb, turn to
next step
Turn to step 7
6
Check whether fault is
removed after replacing
relevant light bulb
Turn Light switch to relevant
light position
Whether relevant light is on
Fault is removed
Next step
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст