BMW 325xi Touring, Wagon (2002 year). Instruction — part 9
123n
Overview
Controls in detail
Operation, maintenance
Owner service procedures
Technical data
Index
Repairs
124n
Onboard tool kit
Windshield wiper blades
The onboard tool kit is located beneath
Windshield
Rear window
the floor panel in the cargo area.
1. Fold the wiper arm completely out
1. Fold the wiper arm completely out
Raising the floor panel, refer to
from the windshield
from the windshield
page 99.
2. Position the wiper blade at an angle
2. Pull out the wiper blade (arrow)
and pull the release spring (arrow)
3. Guide the new wiper blade into
3. Fold the wiper blade down and
place, continue to apply pressure
unhook it toward the windshield
until you hear the detent engage.
4. Pull the wiper blade past the wiper
arm toward the top
5. Insert a new wiper blade and apply
pressure until you hear it engage.
Use only wiper blades approved
by BMW.<
Lamps and bulbs
125n
The lamps and bulbs make essential
When cleaning the headlamps,
contributions to the safety of your
please observe the following:
vehicle. Therefore, comply fully with the
> Do not clean by wiping with a dry
following instructions during bulb
cloth (scratches). Never use abra-
replacement. If you are not familiar with
sives or strong solvents to clean the
any of the procedures, consult your
covers
BMW center.
> Remove dirt and contamination (such
as insects) by soaking with BMW Car
Do not touch the glass portion of
Shampoo and then rinsing with plenty
a new bulb with your bare hands
of water
since even small amounts of impurities
> Always use a deicer spray to remove
burn in to the surface and reduce the
accumulated ice and snow - never
service life of the bulb. Use a clean
use a scraper.<
Low and high beams
cloth, paper napkin, or a similar mate-
rial, or hold the bulb by its metallic
Engine compartment, left side:
Xenon lamps
base.<
1 Low beams
The service life of these bulbs is very
2 High beams
long and the probability of a failure is
A replacement bulb set is available from
very low, provided that they are not
your BMW center.
H7 bulb, 55 watts
switched on and off an unusual number
of times. If one of these bulbs should
Before working on the electrical
The H7 bulb is pressurized. There-
nevertheless fail, it is possible to
fore, wear safety glasses and
system, switch off the electrical
continue driving with great caution
accessory you are working on or
protective gloves. Failure to comply
using the fog lamps, provided local
with this precaution could lead to injury
disconnect the cable from the negative
traffic laws do not prohibit this.
terminal of the battery. Failure to
if the bulb is accidentally damaged
during replacement.<
observe this precaution could result in
Because of the extremely high
short circuits.
voltages involved, any work on the
1. Press the two release catches at the
To prevent injuries and damage,
xenon lighting system should be carried
comply with any instructions provided
front while simultaneously turning
out by technically-qualified personnel
them to the left to remove the bulb
by the bulb manufacturer.<
only. Otherwise, there is a risk of fatal
holder
injury.<
2. Remove and replace the bulb.
126nLamps and bulbs
Parking lamps
Turn signal, front
5 Align the lamp assembly's two ridges
Engine compartment, left side:
21 watt bulb
and the centering pin with the guides
on the vehicle when installing
1. Turn the bulb holder to the left
1 Extend a screwdriver through the
6 Slide in the lamp, applying gentle
(arrow) and remove it
upper opening and loosen the screw,
pressure to seat it firmly
2. Remove and replace the bulb.
continuing until you can extract the
7. Tighten the screw.
bulb by removing it from the front
5 watt bulb
2 Disconnect the plug
3 Apply gentle pressure and turn the
bulb toward the word "AUF" (refer to
the marking on the housing), then
remove it for replacement
4 Connect the plug
Lamps and bulbs
127n
Side turn signals
Tail lamps
Section of the left cargo area:
5 watt bulb
Tail lamp (4): 21/4 watt bulb
Bulbs in the fender:
Other bulbs: 21 watts
All of the bulbs are integrated in a
1. Use finger pressure against the rear
end of the lens (arrow) to press it
1 Turn signal
yellow
central bulb holder.
forward for removal
1. Release and remove the cargo area
2 Backup lamps
white
2. Apply gentle pressure to the bulb
cover panel
3 Tail lamp
red
while turning it to the left to remove.
2. Release and remove the bulb holder
4 Tail lamp/brake lamp
red
(arrow)
3. Remove the power plug and lay the
bulb holder to one side, for instance ,
on the floor of the cargo area
4. Applying light pressure, turn the bulb
to the left. Remove and replace the
bulb
5. Plug in the power supply fitting
6. Press the bulb holder into position
until you hear it engage.
128nLamps and bulbs
Bulbs in tailgate:
2. Fold the trim panel down, release the
License plate lamps
bulb holder and remove
1. Insert a screwdriver in the recess
5 watt bulb
3. Applying light pressure, turn the bulb
(arrow) and press down to release
to the left. Remove and replace the
1. Place a screwdriver in the slot and
the assembly
press toward the left (arrow) to
bulb
4. Press the bulb holder into position
release the lens
2. Replace the bulb.
until you hear it engage
5. Press the trim panel back in,
continuing until you hear it snap into
place.
Center (high-mount) brake lamp
LED strip on the rear window.
Please contact your BMW center in
case of a malfunction.
Lamps and bulbs
Changing a wheel
129n
Safety measures in the event of a
Do not place wooden blocks or similar
flat tire or wheel change:
objects under the jack. They could
Stop the vehicle as far as possible from
prevent the jack from extending to its
passing traffic. Park on a firm, flat,
full height and reduce its support
surface. Switch on the hazard warning
capacity.
flashers. Turn the steering wheel to the
Do not lie under the vehicle or start the
straight-ahead position and engage the
engine when the vehicle is supported
steering lock. Shift into 1st or reverse
by the jack - risk of fatal injury.<
(selector lever in Park with automatic
transmission) and engage the parking
Your BMW is equipped with a spare tire
brake.
or a space-saver spare tire designed for
All passengers should be outside the
temporary use in maintaining the
vehicle and well away from your imme-
vehicle's mobility in an emergency.
Tailgate lamp
diate working area (behind a guardrail,
5 watt bulb
for instance).
To remove the spare tire, lift the
1. Pull out the bulb holder (arrow)
If a warning triangle or portable hazard
floor panel in the cargo area
2. Replace the bulb.
warning lamp is available, set it up on
completely out, refer to page 99.<
the roadside at an appropriate distance
from the rear of the vehicle. Comply
with all local safety guidelines and
regulations.
Change the wheel only on a level, firm
surface which is not slippery. Avoid
jacking the vehicle on a soft or slippery
support surface (snow, ice, loose
gravel, etc.), as either the vehicle or the
jack could slip sideways.
Position the jack on a firm support
surface.
130nChanging a wheel
Procedure
1. Read and comply with the safety
precautions provided on the previous
page
2. Secure the vehicle to prevent it from
rolling:
Place the chock against the rear
surface of the front tire on the side
opposite the side being raised. If the
vehicle is parked on a downward
slope, place the chock securely in
front of the tire. If the wheel must be
> Spare tire or space-saver spare tire
changed on a surface with a more
What you will need
Located next to the jack.
severe slope, take additional precau-
In order to avoid rattling noises later,
Loosen the wingnut (arrow) by hand,
tions to secure the vehicle from
note the position of the tools when you
remove the storage shelf and take the
rolling
remove them and return them to their
wheel out.
3. Wheels with full wheel covers*:
original position when you are done
Reach into the ventilation openings
using them.
and pull the cover off
> Jack 1
Fold up the floor panel, lift away the
spare tire cover, and screw off the
red wingnut (arrow).
When you have completed work,
screw the jack all the way back
down. Fold the handle back and
insert it in its holder
> Chock 2
Behind the vehicle jack. Loosen the
wingnut to remove it
> Lug wrench 3
Changing a wheel
131n
4. Loosen the lug bolts by rotating half
8. Remove accumulations of mud or
13. Wheels with full wheel covers*:
a turn
dirt from the mounting surfaces of
Place the wheel cover with the
5. Position the jack at the jacking point
the wheel and hub. Clean the lug
valve opening (arrow) over the
(arrows) closest to the flat tire so that
bolts
valve. Use both hands to press the
the jack base is vertically below the
9. Position the new wheel or the
cover securely onto the rim
jacking point and the entire surface
space-saver spare tire on the hub
14. Check and correct the tire inflation
of the head of the jack will move into
and screw at least two lug bolts
pressure at the earliest opportunity.
the square recess of the jacking
finger-tight into opposite bolt holes
Vehicles with Tire Pressure Monitor
point (refer to the detail in the next
10. Screw in the remaining lug bolts.
(RDC):
illustration) when the jack is cranked
Screw in all the bolts in a diagonal
After mounting the spare tire or
6. Jack the vehicle up until the wheel
pattern
correcting the inflation pressure,
you are changing is raised from the
11. Lower the jack and remove it from
reactivate the system, refer to
ground
beneath the vehicle
page 78 or 80.
7. Unscrew the lug bolts and remove
12. Tighten the lug bolts securely in a
Protect valve stems and valves from dirt
the wheel
diagonal pattern
using screw-on valve stem caps. Dirty
valve stems frequently lead to slow
pressure loss.
132nChanging a wheel
Only use original BMW full wheel
Driving with the space-saver
Safety tires*
covers, otherwise, the trim piece
spare tire
Safety tires consist of self-supporting
may not fit securely. The full wheel
Drive cautiously. Do not exceed a
tires and special rims. The tire rein-
cover may not be installed on the
speed of 50 mph (80 km/h).
forcement ensures that the tire retains
space-saver spare tire, since this could
some residual safety in the event of
You can anticipate changes in vehicle
damage the cover.<
pressure drop and driving remains
handling such as delayed braking
possible to a restricted degree. The
response, longer braking distances and
The vehicle jack is designed for
vehicle is equipped with Tire Pressure
sacrifices in roadholding.
changing wheels only. Do not
Monitor (RDC) or Flat Tire Monitor,
attempt to raise another vehicle model
The changes in handling characteristics
which indicate a flat tire.
with it or to raise any load of any kind.
will be even more pronounced if winter
To do so could cause accidents and
tires are mounted.
Flat tire
personal injury.
If there is a tire failure, the red warning
To ensure continued safety, have the
Only one space-saver spare tire
lamp symbol lights up. A supplemen-
tightness of the lug bolts checked with
may be mounted at a time. Rein-
tary gong is also heard.
a calibrated torque wrench [torque
stall wheels and tires of the same size
For additional information on Tire Pres-
specification: 72 lb ft (100 Nm)] at the
and specification as soon as possible.
sure Monitor (RDC) or Flat Tire Monitor
earliest opportunity.<
Maintain correct tire pressures, refer to
refer to page 78 or 80.
page 24.<
When storing a wheel in the spare tire
Reduce vehicle speed carefully to
recess take care to avoid bending the
under 50 mph (80 km/h), avoiding hard
threaded rod.
brake applications and steering maneu-
vers.
If the original BMW light-alloy wheels
have been replaced with other light-
With the safety tires, you can drive
alloy wheels, different lug bolts may be
another approx. 155 miles (250 km) to
required.
reach a safe parking location, a service
station or the nearest BMW center.
Replace the defective tire as soon as
With a low vehicle load, this can also be
possible and have the new wheel/tire
considerably more than 155 miles
balanced.
(250 km).
Changing a wheel
Battery
Fuses
133n
Safety tires are only possible in
Battery care
conjunction with Tire Pressure
The battery is absolutely maintenance-
Monitor (RDC) or Flat Tire Monitor.<
free, that is, the original electrolyte will
normally last for the service life of the
If the defective wheel cannot be seen
battery under moderate climatic condi-
as such immediately from the outside,
tions.
check the tire inflation pressure at all
four wheels.
Please consult your BMW center
whenever you have any questions
Have the tires changed by your
concerning the battery. Since the battery
BMW center. For safety reasons,
is absolutely maintenance-free, the
do not have a safety tire repaired. Your
following is for your information only.<
BMW center has the information
The fuses are located in the glove
needed for working with safety tires
Never disconnect the battery
compartment behind a cover secured
and is equipped with the necessary
when the engine is running; the
by two snap clips.
special tools.<
ensuing voltage surge would seriously
damage the vehicle's onboard elec-
Do not attempt to repair a blown
If appropriate, please consult your
tronic systems.<
fuse or replace it with a fuse
BMW center to reequip your
having a different color or amperage
vehicle from summer to winter tires - or
Charging the battery
rating. To do this could cause a fire in
vice versa.<
When charging the battery in the
the vehicle resulting from a circuit over-
load.<
vehicle, leave the engine off at all times.
Connect the charge cables to the termi-
nals in the engine compartment.
Terminal locations, refer to Jump-
starting on page 134.
Return used batteries to a recycling
point or your BMW center. Maintain
the battery in an upright position for
transport and storage. Secure the
battery against tilting during transport.<
134n
Jump-starting
Do not use spray starter fluids to start
Always adhere to this sequence
the engine.
when connecting jumper cables;
failure to observe this procedure can
When your battery is discharged you can
lead to sparks at the battery terminals
used two jumper cables to start your
and pose an injury hazard.<
vehicle with power from the battery in a
second vehicle. You can also use the
7. Start the support vehicle's engine
same method to help start another
and let it run at an increased idling
vehicle. Always use jumper cables with
speed for a few minutes. Start the
fully insulated handles on the terminal
engine on the vehicle needing the
clamps.
jump-start, and allow it to run as
usual. If the first start attempt is not
Do not touch high-voltage wiring
successful, wait a few minutes
and cables on a running engine.
4. Start the engine on the support
before another attempt in order to
Contact with components carrying high
vehicle and allow it to run
allow the discharged battery to
voltage can be harmful or fatal. Care-
5. Use one jumper cable (+) to connect
recharge
fully observe the following instructions
the positive terminal of the battery in
8. Before disconnecting the jumper
to avoid personal injury and/or damage
the support vehicle with the auxiliary
cables let the engines run for a few
to one or both vehicles.<
positive terminal provided in the
minutes
engine compartment of your BMW
9. Then disconnect the jumper cables
1. Ensure that the battery in the support
(arrow 1). The cover on this auxiliary
in reverse sequence.
vehicle is also rated at 12 volts. This
terminal is identified by a "+" symbol.
information is provided on the top of
Remove by pulling the tab
Depending on the cause of the fault,
the battery casing
6. Next, connect one end of the other
have the battery recharged by your
2. Do not disconnect your battery from
jumper cable (-) to either the support
BMW center.
your vehicle's electrical system.
vehicle's negative battery terminal or
Switch off all electrical accessories in
a suitable ground on its engine or
both vehicles
bodywork. Connect the other end to
3. Make absolutely certain that there is
the negative battery terminal or a
no contact between the bodywork of
suitable ground on the vehicle being
the two vehicles - short circuit
started. There is a special nut on
hazard
your BMW (2)
Towing the vehicle
135n
Tow fitting
Rear:
Towing with a commercial tow
Press out the cover panel with a screw-
The screw-in tow fitting is stored in the
truck
driver inserted in the recess at the top.
onboard tool kit; be sure that it remains
> Do not tow with sling-type equipment
in the vehicle at all times. This fitting is
> Use wheel-lift or flatbed equipment
Screw the tow fitting all the way
designed for installation in the tow
> Please comply with applicable state
in. Failure to screw the fitting all
sockets located at the front and rear of
towing laws.
the way in can cause thread damage.
the vehicle, and is intended for towing
Never attach tie-down hooks, chains,
on paved road surfaces only. This fitting
Never allow passengers to ride in
straps, or tow hooks to tie rods, control
should not be used to pull a vehicle out
a towed vehicle for any reason.
arms, or any other part of the vehicle
of deep snow, mud, sand, etc.
Never attach tie-down hooks, chains,
suspension, as severe damage to these
Always comply with all applicable
straps, or tow hooks to tie rods, control
components will occur, leading to
towing laws and regulations.
arms, or any other part of the vehicle
possible accidents.<
suspension, as severe damage to these
Access to tow sockets
components will occur, leading to
possible accidents.c
Front:
Press out the cover panel with a screw-
driver inserted in the recess at the top.
136nTowing the vehicle
BMW 325xi, 330xi, 330xd:
Towing with a raised axle
1 Place the transmission in neutral
2 Switch off the engine
3 Towing speed:
30 mph (50 km/h)
4 Towing distance:
max. 95 miles (150 km).
Remove the rear driveshaft for
longer towing distances with the
front axle lifted; remove the front drive-
shaft for towing over longer distances
with the rear axle lifted. Failure to
comply with this will result in damage to
the transfer box.<
Большое спасибо!
Ваше мнение очень важно для нас.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст