BMW 325Ci Coupe (2006 year). Instruction — part 8
Giving and receiving assistance
124
Your BMW has a special nut as body ground
or negative pole.
5.
Attach the second terminal clamp of the
minus/– jumper cable to the negative termi-
nal of the battery or to the engine or body
ground of the vehicle to be started.
Starting the engine
1.
Start the engine of the donor vehicle and
allow it to run for a few minutes at slightly
increased idle speed.
2.
Start the engine on the other vehicle in the
usual way.
If the first start attempt is not successful,
wait a few minutes before another attempt
in order to allow the discharged battery to
recharge.
3.
Let the engines run for a few minutes.
4.
Disconnect the jumper cables by reversing
the above connecting sequence.
If necessary, have the battery checked and
recharged.
Never use spray fluids to start the
engine.
<
Tow-starting, towing away
Observe the applicable laws and regula-
tions for tow-starting and towing vehi-
cles.
<
Do not transport any passengers other
than the driver in a vehicle that is being
towed.
<
Using a tow fitting
The screw-in tow fitting must always be carried
in the car. It can be screwed in at the front or
rear of the BMW.
It is stored in the onboard tool kit underneath
the cover on the right-hand side of the cargo
bay, refer to page
.
Use only the tow fitting provided with the
vehicle and screw it all the way in. Use the
tow fitting for towing on paved roads only. Avoid
lateral loading of the tow fitting, e.g. do not lift
the vehicle by the tow fitting. Otherwise the tow
fitting and the vehicle could be damaged.
<
Access to screw thread
Rectangular cover panel in bumper:
Press on the upper edges of the cover panel.
Front
Rear
Being towed
Check that the car is radio-ready and that
the electric steering wheel lock is not
engaged, otherwise the car would not be steer-
able. If the electrical system fails, do not
attempt to tow-start or tow away the car. The
electric steering wheel lock cannot be disen-
ba5_E9293_EUR_US.book Seite 124 Donnerstag, 4. Mai 2006 1:08 13
125
gaged and the car is not steerable. Jump start-
ing, refer to page
.
Power steering assistance is not available when
the engine is not running. Thus, braking and
steering will require increased effort.
<
Switch on the hazard warning flashers, depend-
ing on local regulations.
Manual transmission
Gearshift lever in idle position.
Automatic transmission
Selector lever in position N.
Changing selector lever positions, refer to
page
Do not exceed a towing speed of 45 mph
or 70 km/h and a towing distance of
90 miles/150 km, otherwise the automatic
transmission may be damaged.
<
Towing methods
In come countries, it is illegal to tow your vehicle
with a tow bar or tow rope on public highways.
Please familiarize yourself with the relevant
towing regulations for the country in which you
are driving.
With a tow bar
The towing vehicle must not be lighter
than the towed vehicle, otherwise it may
be impossible to maintain control.
<
The tow fittings used should be on the same
side on both vehicles. Should it prove impossi-
ble to avoid mounting the tow bar at an angle,
please observe the following:
>
Clearance and maneuvering capability will
be sharply limited during cornering.
>
The tow bar will generate lateral forces if it is
attached offset.
Attach the tow bar to the tow fittings only,
as attaching it to other parts of the vehicle
could result in damage.
<
With a tow rope
When starting off in the towing vehicle, make
sure that the tow rope is taut.
To avoid jerking and the associated
stresses on vehicle components when
towing, always use nylon ropes or nylon straps.
Attach the tow rope to the tow fittings only, as
attaching it to other parts of the vehicle could
result in damage.
<
With a tow truck
328i, 335i
Have the BMW transported with a tow truck
with a so-called lift bar or on a flat bed.
Do not lift the vehicle by a tow fitting or
body and chassis parts, otherwise dam-
age may result.
<
Tow-starting
Avoid tow-starting the vehicle whenever possi-
ble; instead, jump-start the engine, refer to
page
. Vehicles with a catalytic converter
should only be tow-started when the engine is
cold; vehicles with an automatic transmission
cannot be tow-started at all.
If the electrical system fails, do not tow or
tow-start the vehicle, as it would be
impossible to release the electric steering-
wheel lock and the vehicle could not be
steered.
<
1.
Switch on hazard warning flashers, comply
with local regulations.
2.
Switch on the ignition, refer to page
3.
Shift into 3rd gear.
ba5_E9293_EUR_US.book Seite 125 Donnerstag, 4. Mai 2006 1:08 13
Giving and receiving assistance
126
4.
Have the vehicle tow-started with the clutch
depressed and slowly release the clutch.
After the engine starts, immediately
depress the clutch completely.
5.
Stop at a suitable location, remove the tow
bar or rope and switch off the hazard warn-
ing flashers.
6.
Have the vehicle checked.
ba5_E9293_EUR_US.book Seite 126 Donnerstag, 4. Mai 2006 1:08 13
127
Indicator and warning lamps
Indicator and warning lamps appear in indicator
area
1 and display 2. See the table for informa-
tion on causes and how to react. Note whether a
lamp comes on alone or in combination with
another. Some lamps can light up in different
colors. Corresponding distinctions are made in
the text.
1
2
Cause
What to do
Turn signals
High beams/headlamp flasher
switched on
Fog lamps switched on
Fasten safety belts
Fasten your safety belt, refer also to
page
Indication in US models
Handbrake engaged
Release the handbrake.
Indication in Canadian models
Handbrake engaged
Release the handbrake.
Outside temperature warning
Drive cautiously, refer also to page
.
Lights up briefly:
Approx. 2.1 US gallons/8 liters of fuel
remain in the tank
Remains on:
Remaining operating range is no more
than 30 miles/50 km, refer to page
Engine refuses to start
Depress the brake or clutch in order to
start the engine, refer to page
42
.
Ignition switched on and driver's door
open
Switch off the ignition, refer to page
,
or close the driver's door.
Parking lamps still on
Switch off the parking lamps, refer to
page
Roadside parking lamps still on
Switch off the roadside parking lamps,
refer to page
ba5_E9293_EUR_US.book Seite 127 Donnerstag, 4. Mai 2006 1:08 13
Indicator and warning lamps
128
Door open
Engine compartment lid open
Luggage compartment lid open
Gas cap missing or loose
Close the gas cap until there is a clearly
audible click. Do not jam the strap
between the gas cap and the vehicle.
Windshield washer fluid level too low
Add washer fluid as soon as possible,
refer to page
.
Lights up in red:
Service due
Arrange a service appointment.
Check service requirements, refer to
page
.
Lights up in yellow:
The engine will start the next time the
start/stop button is touched, possibly
without the brake or clutch being
depressed
Remote control malfunctioning or, in
cars with convenient access, not
detected
The engine cannot be started. Have the
remote control checked, if necessary.
Battery in remote control discharged
Use the remote control for a longer jour-
ney or, in cars with convenient access,
replace the battery.
Belt tensioners and/or airbag system
failed
Have the system checked immediately.
Active steering defective
You can continue your journey.
Steering characteristics are modified
and steering wheel could be off-center.
Steer carefully.
Have the system checked as soon as
possible.
Lights up:
Emergency call system has failed or is
malfunctioning
Have the system checked as soon as
possible.
1
2
Cause
What to do
ba5_E9293_EUR_US.book Seite 128 Donnerstag, 4. Mai 2006 1:08 13
129
Lights up in red:
Engine malfunction
Stop the car and switch off the engine.
You cannot continue your journey. Con-
tact your BMW center.
Lights up in yellow:
Full engine power no longer available
You can continue your journey, but
moderate your speed and exercise due
caution. Have the engine checked as
soon as possible.
Indication in US models:
Indicator lamp
1 flashes:
Engine malfunction under high load.
High engine load will result in damage
to the catalytic converter
You can continue your journey, but
moderate your speed and exercise due
caution. Have the vehicle checked with-
out delay.
Indicator lamp
1 comes on:
Engine malfunction with adverse effect
on exhaust emissions
Have the car checked as soon as possi-
ble.
Indication in Canadian models:
Indicator lamp
1 flashes:
Engine malfunction under high load.
High engine load will result in damage
to the catalytic converter
You can continue your journey, but
moderate your speed and exercise due
caution. Have the vehicle checked with-
out delay.
Indicator lamp
1 comes on:
Engine malfunction with adverse effect
on exhaust emissions
Have the car checked as soon as possi-
ble.
Lights up in red:
Engine overheating
Carefully bring the car to a stop, switch
off the engine and allow it to cool down.
Do not open the engine compartment
lid, otherwise there would be a risk of
injury by scalding. Contact your BMW
center.
Lights up in yellow:
Engine too hot
Continue driving at more moderate
speed so that the engine can cool
down. Have the engine checked with-
out delay if the situation reoccurs.
1
2
Cause
What to do
ba5_E9293_EUR_US.book Seite 129 Donnerstag, 4. Mai 2006 1:08 13
Indicator and warning lamps
130
Lights up in red:
Battery is no longer being charged.
Alternator malfunction
Switch off all unnecessary electrical
consumers. Have the battery checked
without delay.
Lights up in yellow:
Battery charge level very low, battery
aged or not securely connected
Have the battery checked as soon as
possible.
Indication in US models
Handbrake engaged
Indication in Canadian models
Handbrake engaged
Indication in US models
Lights up in red:
Brake fluid level too low
Brake-pedal travel may be considerably
longer. You can continue your journey,
but moderate your speed and exercise
due caution. Have the system checked
immediately.
Lights up in yellow:
Drive-off assistant has failed. The car
will not be held in place after the brake
is released
Have the system checked as soon as
possible.
Indication in Canadian models
Lights up in red:
Brake fluid level too low
Brake-pedal travel may be considerably
longer. You can continue your journey,
but moderate your speed and exercise
due caution. Have the system checked
immediately.
Lights up in yellow:
Drive-off assistant has failed. The car
will not be held in place after the brake
is released
Have the system checked as soon as
possible.
Indication in US models
Brake pads worn
Have the condition of the brake pads
checked without delay.
Indication in Canadian models
Brake pads worn
Have the condition of the brake pads
checked without delay.
1
2
Cause
What to do
ba5_E9293_EUR_US.book Seite 130 Donnerstag, 4. Mai 2006 1:08 13
131
Indication in US models
Vehicle electronics failed
You cannot continue your journey. Con-
tact your BMW center.
Indication
*
in Canadian models
Vehicle electronics failed
You cannot continue your journey. Con-
tact your BMW center.
Indication
*
in Canadian models
Vehicle electronics failed
You cannot continue your journey. Con-
tact your BMW center.
Lights up in red:
Have the system in question checked
without delay.
>
Starter failed or
The engine cannot be restarted.
>
ignition malfunctioning. Engine
restart only possible when brake is
depressed or
>
lighting system failed. Low beams/
tail lamps and brake lamps still
operational. All other lamps failed
Depress the brake to restart the engine.
Lights up in yellow:
>
Control of the brake lamps failed or
>
fuel supply malfunctioning, or
>
trailer lamps malfunctioning
You can continue your journey, but
moderate your speed and exercise due
caution. Have the system in question
checked without delay.
Flashing:
Dynamic Stability Control DSC or
Dynamic Traction Control DTC is con-
trolling drive and braking forces, refer
also to page
Dynamic Traction Control DTC acti-
vated, refer also to page
Dynamic Stability Control DSC and
Dynamic Traction Control DTC deacti-
vated, refer also to page
Driving stability limited during accelera-
tion and cornering.
Driving style must be adjusted.
1
2
Cause
What to do
ba5_E9293_EUR_US.book Seite 131 Donnerstag, 4. Mai 2006 1:08 13
Indicator and warning lamps
132
Suspension control system failed, refer
also to page
Driving stability limited during accelera-
tion and cornering.
You can continue your journey, but
moderate your speed and exercise due
caution. Have the system checked as
soon as possible.
Indication in US models
The driving stability control systems,
including ABS and the Tire Pressure
Monitor, have failed, refer also to
page
You can continue your journey. Drive
cautiously and think well ahead. Avoid
situations that require full braking. Have
the system checked immediately.
Indication
*
in Canadian models
The driving stability control systems,
including ABS and the Flat Tire Monitor
or Tire Pressure Monitor
*
, have failed,
refer also to page
You can continue your journey. Drive
cautiously and think well ahead. Avoid
situations that require full braking. Have
the system checked immediately.
Indication
*
in Canadian models
The driving stability control systems,
including ABS and the Flat Tire Monitor
or Tire Pressure Monitor
*
, have failed,
refer also to page
You can continue your journey. Drive
cautiously and think well ahead. Avoid
situations that require full braking. Have
the system checked immediately.
Vehicles with Flat Tire Monitor
*
Light up in yellow and red:
>
Tire is deflated
Carefully bring the car to a stop. Comply
with the additional information starting
on page
.
>
Flat Tire Monitor not initialized
Initialize Flat Tire Monitor, refer to
page
.
Light up in yellow:
Flat Tire Monitor failed. Punctures are
not indicated
Have the system checked.
1
2
Cause
What to do
ba5_E9293_EUR_US.book Seite 132 Donnerstag, 4. Mai 2006 1:08 13
133
Vehicles with Tire Pressure Monitor
*
Light up in yellow and red:
There is a flat tire or substantial loss of
tire pressure
Carefully bring the car to a stop. Comply
with the additional information starting
on page
Light up in yellow:
Tire Pressure Monitor not initialized
Check the inflation pressure and reset
the system, refer to page
.
The small lamp flashes in yellow and
then lights up continuously; the larger
lamp comes on in yellow:
Tire Pressure Monitor has failed. Punc-
tures are not indicated
Have the system checked. Comply with
the additional information starting on
page
Lights up in red:
>
Transmission limp-home program
active with restricted range of
gears, possibly with reduced accel-
eration
You can continue your journey, but
moderate your speed and exercise due
caution. Have the system checked
without delay.
Gears can be engaged without
depressing the brake
Always depress the brake to engage a
gear.
Lights up in yellow:
Have the system checked as soon as
possible.
>
Automatic selector lever locked:
Selector lever locked in position P
with engine running and brake
depressed or
Overriding selector lever lock, refer to
page
>
brake signal malfunctioning: gear
can be engaged without depress-
ing the brake
To engage a gear while the vehicle is at
a standstill, always step on the brake.
Before leaving the vehicle, move the
selector lever to position P and switch
off the engine.
Lights up in red:
Transmission overheating
Bring the car to a stop and move the
selector lever to position P. Allow the
transmission to cool down. You can
continue your journey, but moderate
your speed and exercise due caution.
Have the system checked if the situa-
tion reoccurs.
Lights up in yellow:
1
2
Cause
What to do
ba5_E9293_EUR_US.book Seite 133 Donnerstag, 4. Mai 2006 1:08 13
Indicator and warning lamps
134
Transmission too hot
Avoid high engine loads. You can con-
tinue your journey, but moderate your
speed and exercise due caution.
Selector lever position P not engaged.
Vehicle not prevented from rolling
Selector lever position P not engaged.
Ignition cannot be switched off
Engage selector lever position P when
you wish to switch off the ignition, refer
to page
.
Lights up in red:
Electric steering wheel lock malfunc-
tioning
The engine can no longer be started. If
applicable, do not switch off the engine.
Contact your BMW center.
Lights up in yellow:
Electric steering wheel lock jammed
Move the steering wheel before starting
the engine.
Pinch protection system of the power
windows malfunctioning
Have the system checked.
Pinch protection system of the electric
glass sunroof malfunctioning
Have the system checked.
Cruise control deactivated:
>
Driving stability control systems are
active or
>
handbrake is applied or
>
the vehicle has not achieved a
speed of 20 mph or 30 km/h or
>
engaged gear not suitable for the
speed being driven
Cruise control system failed
You can continue your journey. Have
the system checked.
Active cruise control deactivated:
>
Driving stability control systems are
active or
>
handbrake is applied or
>
the vehicle has not achieved a
speed of 20 mph or 30 km/h or
>
engaged gear not suitable for the
speed being driven or
Keep a safe distance.
>
radar sensor dirty
Clean the radar sensor, refer to
page
.
1
2
Cause
What to do
ba5_E9293_EUR_US.book Seite 134 Donnerstag, 4. Mai 2006 1:08 13
135
Active cruise control failed
Keep a safe distance.
Have the system checked.
Park Distance Control failed
Have the system checked.
Bulb of exterior lighting system failed
Have the exterior lighting checked as
soon as possible.
Low-beam headlamp or fog lamp failed Have the low beams checked as soon
as possible.
High-beam headlamp failed
Have the high-beam headlamps
checked.
Headlamp beam throw adjustment
system failed
Have the headlamp beam throw adjust-
ment system checked.
Adaptive Head Light failed
Coolant level too low
Add coolant immediately, refer to
page
Engine oil pressure too low
Stop immediately and switch off the
engine. You cannot continue your jour-
ney. Contact your BMW center.
Engine oil level too low
Add engine oil immediately; refer to
page
for more information.
Lights up in red:
Service appointment overdue
Arrange a service appointment.
Check service requirements, refer to
page
Lights up in yellow:
Service due
Arrange a service appointment.
Check service requirements, refer to
page
No service due
Check service requirements, refer to
page
Time and date no longer correct
Set the time and date, refer to page
.
1
2
Cause
What to do
ba5_E9293_EUR_US.book Seite 135 Donnerstag, 4. Mai 2006 1:08 13
Technical data
138
Technical data
Engine data
328i
335i
Displacement
cu in/cm
µ
182.8/2,996 181.8/2,979
Number of cylinders
6
6
Maximum power output
hp
230
300
at engine speed
rpm
6,500
5,800
Maximum torque
lb ft/Nm
200/270
300/407
at engine speed
rpm
2,750 1,400-5,000
ba5_E9293_EUR_US.book Seite 138 Donnerstag, 4. Mai 2006 1:08 13
139
Dimensions
All dimensions given in inches/mm. Smallest turning circle diam.: 36 ft 1 in/11.0 m
335i: height approx. 4 ft 6 in/1,375 mm
ba5_E9293_EUR_US.book Seite 139 Donnerstag, 4. Mai 2006 1:08 13
Technical data
140
Weights
328i
335i
Curb weight
>
with manual transmission
lbs/kg
3,351/1,520
3,571/1,620
>
with automatic transmission lbs/kg
3,417/1,550
3,582/1,625
Approved gross weight
>
with manual transmission
lbs/kg
4,277/1,940
4,497/2,040
>
with automatic transmission lbs/kg
4,343/1,970
4,508/2,045
Load
lbs/kg
926/420
926/420
Approved front axle load
lbs/kg
2,061/935
2,172/985
Approved rear axle load
lbs/kg
2,293/1,040
2,348/1,065
Approved roof load capacity
lbs/kg
165/75
165/75
Cargo bay capacity
cu ft/l
15.5/440
15.2/430
ba5_E9293_EUR_US.book Seite 140 Donnerstag, 4. Mai 2006 1:08 13
141
Capacities
Notes
Fuel tank
US gal/liters
approx. 16.1/61
Fuel grade: page
including reserve of
US gal/liters
approx. 2.1/8.0
Window washer system
For more details: page
including headlamp washers US
quarts/liters
approx.
6.3/6.0
Engine with oil filter renewal
US quarts/liters
approx. 6.9/6.5 BMW High Performance
Synthetic Oil
Oil grades: page
ba5_E9293_EUR_US.book Seite 141 Donnerstag, 4. Mai 2006 1:08 13
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст