BMW 325Ci Coupe (2006 year). Instruction — part 2

Opening and closing

Raising

Press the switch.

The closed glass sunroof is raised and the
sliding visor opens slightly.

The open glass sunroof automatically trav-
els into the raised position. The sliding visor
remains completely open.

Opening, closing

Push the switch backwards to the resis-
tance point.
The glass sunroof and the sliding visor open
together as long as you hold the switch in
this position.

Push the switch backwards past the resis-
tance point.
The glass sunroof and the sliding visor open
automatically. Briefly push the switch again
to stop the opening movement.

You can close the glass sunroof in a similar
manner by pushing the switch forwards. The
sliding visor remains open and can be closed by
hand.
For information on convenient operation via the
remote control or door lock, refer to page

After switching off the ignition

When the remote control is removed or the igni-
tion is switched off, you can still operate the
sunroof for approx. 1 minute as long as no door
has been opened.

Pinch protection system

If the glass sunroof encounters an obstruction
during closing from approximately the middle of

the opening in the roof, or during closing from
the raised position, the closing movement is
interrupted and the glass sunroof is opened
again slightly.

Despite the pinch protection system
check and clear the sunroof's travel path

prior to closing it, otherwise the safety system
might fail to detect certain kinds of obstruc-
tions, such as very thin objects, and the sunroof
would continue closing.
Pushing the switch beyond the resistance point
and holding it there deactivates the pinch pro-
tection system.

Following interruptions in electrical

power supply

After a power failure, there is a possibility that
the glass sunroof can only be raised. The sys-
tem must be initialized. BMW recommends
having this work done by your BMW center.

Closing manually

In the event of an electrical malfunction, you can
move the glass sunroof manually:

Unclip the front of the cover of the interior
lamps using the screwdriver from the
onboard tool kit, refer to page

117

ba5_E9293_EUR_US.book Seite 28 Donnerstag, 4. Mai 2006 1:08 13

Insert the screwdriver into the openings on
each side to press the clips.

Remove the control unit.

Unplug the motor. Considerably less effort
will be required for manual operation.

Insert the Allen wrench supplied with the
onboard tool kit, refer to page

117

, into the

opening provided. Move the glass sunroof
in the desired direction.

Reinstall the control unit and reattach the
lamp cover.

ba5_E9293_EUR_US.book Seite 29 Donnerstag, 4. Mai 2006 1:08 13

Adjustments

Sitting safely

The ideal sitting position can make a vital con-
tribution to relaxed, fatigue-free driving. In con-
junction with the safety belts, the head
restraints and the airbags, the seated position
has a major influence on your safety in the event
of an accident. To ensure that the safety sys-
tems operate with optimal efficiency, we
strongly urge you to observe the instructions
contained in the following section.
For additional information on transporting chil-
dren safely, refer to page

Airbags

Always maintain an adequate distance
between yourself and the airbags. Always

grip the steering wheel on the rim, with your
hands in the 3 o'clock and 9 o'clock positions,
to minimize the risk of injury to the hands or
arms in the event of the airbag being triggered
off.
No one and nothing is to come between the air-
bags and the seat occupant.
Do not use the cover of the front airbag on the
front passenger side as a storage area. Make
sure that the front passenger is sitting correctly,
i.e. not resting feet or legs on the dashboard.
Otherwise leg injury could result should the
front airbag deploy.
Make sure that passengers do not lean their
heads against the side or head airbags, other-
wise serious injuries could result if the side air-
bags suddenly deployed.

Even if you follow all the instructions, injuries
resulting from contact with airbags cannot be
fully excluded, depending on the circum-
stances. The ignition and inflation noise may
provoke a mild hearing loss in extremely sensi-
tive individuals. This effect is usually only tem-
porary.
For airbag locations and additional information
on airbags, refer to page

Head restraint

A correctly adjusted head restraint reduces the
risk of neck injury in the event of an accident.

Adjust the head restraint in such a way
that its center is at approx. ear level. Oth-

erwise, there is an increased risk of injury in the
event of an accident.

Head restraints, refer to page

Safety belt

Before every drive, make sure that all occupants
wear their safety belts. Airbags complement the
safety belt as an additional safety device, but
they do not represent a substitute.

Never allow more than one person to
wear a single safety belt. Never allow

infants or small children to ride in a passenger's
lap. Make sure that the belt in the lap area sits
low across the hips and does not press against
the abdomen.
The safety belt must not rest against the throat,
run across sharp edges, pass over hard or frag-
ile objects or be pinched. Fasten the safety belt
so that it sits as snugly as possible against the
lap and shoulder without being twisted. Other-
wise the belt could slide over your hips and
injure your abdomen in the event of a frontal
collision.
Avoid wearing bulky clothing and regularly pull
the belt in the upper-body area taut, otherwise
its restraining effect could be impaired.

Safety belts, refer to page

Seats

Note before adjusting

Never attempt to adjust your seat while
the vehicle is moving. The seat could

respond with unexpected movement, and the
ensuing loss of vehicle control could lead to an
accident.
On the front passenger seat as well, do not

ba5_E9293_EUR_US.book Seite 30 Donnerstag, 4. Mai 2006 1:08 13

incline the backrest too far to the rear while the
vehicle is being driven, otherwise there is a dan-
ger in the event of an accident of sliding under
the safety belt, eliminating the protection nor-
mally provided by the belt.

Comply with the instructions on head restraint
height on page

, and on damaged safety

belts on page

Manual adjustment

Observe the adjustment instructions on
page

to ensure the best possible per-

sonal protection.

Longitudinal direction

Pull lever

1 and slide the seat to the desired

position.
After releasing the lever, move the seat gently
forward or back to make sure it engages prop-
erly.

Height

Pull lever

2 and apply your weight to the seat or

lift it off, as necessary.

Backrest

Tilt*

Pull the lever and apply your weight to the seat
or lift it off, as necessary.

Thigh support*

Pull the lever and move the thigh support for-
ward or back.

Electrical adjustment

Observe the adjustment instructions on
page

to ensure the best possible per-

sonal protection.

ba5_E9293_EUR_US.book Seite 31 Donnerstag, 4. Mai 2006 1:08 13

Adjustments

1 Longitudinal direction
2 Height
3 Angle

4 Backrest
The head restraints are adjusted manually, refer
to Head restraints below.

Longitudinal adjustment from outside/

behind*

To move the front seats forward or backward
from outside or from one of the rear seats: press
the front or rear end of the button, respectively.

Lumbar support*

You can also adjust the contour of the backrest
to obtain additional support in the lumbar
region.
The upper hips and spinal column receive sup-
plementary support to help you maintain a
relaxed, upright sitting position.

Increase or decrease curvature: press the
switch at the front or rear, respectively.

Shift curvature up or down: press the switch
at the top or bottom, respectively.

Backrest width*

You can change the width of the backrest to suit
your individual preferences by adjusting the lat-
eral-support pads.
Press the switch at the front or rear end, as
applicable.
Backrest width decreases or increases accord-
ingly.

Head restraints

A correctly adjusted head restraint reduces the
risk of neck injury in the event of an accident.

Adjust the head restraint in such a way
that its center is at approx. ear level. Oth-

ba5_E9293_EUR_US.book Seite 32 Donnerstag, 4. Mai 2006 1:08 13

erwise, there is an increased risk of injury in the
event of an accident.

Front seats

Height adjustment

To raise: pull up.

To lower: press the button, arrow

1, and

slide the head restraint down.

Removing

Pull up all the way.

Press the button, arrow

1, and pull the head

restraint all the way out.

Only remove a head restraint if no pas-
senger will be traveling on the seat in

question. Otherwise, this represents a legal vio-
lation. Reinstall the head restraint before trans-
porting a passenger on that seat.

Rear seats

Height adjustment

To raise: pull up.

To lower: press the button, arrow

1, and

slide the head restraint down.

Removing

Pull up all the way.

Press the button, arrow

1, and pull out the

head restraint completely while the rear
seat backrest is swung forward slightly.

Note that it constitutes a legal violation to
drive with the rear seats occupied and the

rear head restraints removed. Reinstall head
restraints before transporting passengers in the
rear.

Entering the rear seats

Seat with manual longitudinal

adjustment

Convenient entry

The convenient entry feature includes a mem-
ory function for the longitudinal adjustment and
backrest angle.

Pull the lever and swing the backrest for-
ward.

Push the seat forward.

Previous position

Push the seat backward and swing the backrest
back.

When pushing the seat into its rearmost
position, make sure that no one is injured

and that no objects are damaged.
Before driving off, engage both seats and back-
rests so that they are locked in place. Otherwise
there is a risk of accident due to an unexpected
movement.

ba5_E9293_EUR_US.book Seite 33 Donnerstag, 4. Mai 2006 1:08 13

Adjustments

Seat with electrical longitudinal
adjustment

Convenient entry

The convenient entry feature includes a mem-
ory function for the longitudinal adjustment and
backrest angle.

Pull lever

1 and swing the backrest forward.

Press the front end of the button, arrow

until the seat has moved into the desired
position.

Previous position

Press the rear end of the the button, arrow

until the seat automatically stops in its previous
position, and swing the backrest back. If you
release the button before the previous seat
position is reached, the seat will stop at its cur-
rent position.

When pushing the seat into its rearmost
position, make sure that no one is injured

and that no objects are damaged.
Before driving off, engage both seats and back-
rests so that they are locked in place. Otherwise
there is a risk of accident due to an unexpected
movement.

Heated seats*

Press once for each temperature level.
Three LEDs indicate the highest temperature.
To switch off:
Press button longer.
If you continue driving within approx. the next
15 minutes, the seat heating is automatically
activated at the previously set temperature.

Seat and mirror memory*

You can store and call up two different combi-
nations of driver's-seat and exterior-mirror
positions.
Settings for the seat back width and lumbar
support are not stored in memory.

Storing

Switch on radio readiness or the ignition,
refer to page

Adjust the seat and exterior mirrors to the
desired positions.

Press the

button.

The LED in the button lights up.

Press the desired memory key

1 or 2.

The LED goes out.

ba5_E9293_EUR_US.book Seite 34 Donnerstag, 4. Mai 2006 1:08 13

The driver's seat and exterior mirror posi-
tions are stored for the remote control cur-
rently in use.

Automatic call-up

The driver's seat position last stored is stored
for the remote control currently in use.
You can select the occasion on which the seat is
reset to that position.

Call-up when the vehicle is unlocked

Call-up when the driver's door is opened.

When this Personal Profile function is
used, first make sure that the footwell

behind the driver's seat is free of obstacles.
Failure to do so could cause injury to persons or
damage to objects as a result of a rearward
movement of the seat.

The adjusting procedure is halted when you
touch a seat adjustment switch or one of the
MEMORY buttons.

Activating/deactivating automatic call-
up

For operating principle refer to page

Lightly push button

1 in the turn indicator

stalk up or down repeatedly until the symbol
appears in the display accompanied by the
word "SET".

Press button

Lightly push button

1 in the turn indicator

stalk down repeatedly until the symbol
appears in the display.

Press button

Use button

1 to select:

Call-up when the vehicle is unlocked.

Call-up when the driver's door is
opened.

Switch off automatic function.

Press button

The setting is stored.

Manual call-up

Do not call up memory while you are driv-
ing, otherwise unexpected seat move-

ment could result in an accident.

Convenience mode

Unlock and open the driver's door or switch
on radio readiness, refer to page

Briefly press the desired memory button

The adjusting procedure is halted when you
touch a seat adjustment switch or one of the
MEMORY buttons.

Safety feature

Close the driver's door and switch the igni-
tion on or off, refer to page

Press the desired memory button

1 or 2

and maintain pressure until the adjustment
process has been completed.

ba5_E9293_EUR_US.book Seite 35 Donnerstag, 4. Mai 2006 1:08 13

Adjustments

If the

button was pressed accidentally:

press the button again; the LED goes out.

Safety belts

Observe the adjustment instructions on
page

to ensure the best possible per-

sonal protection.

Before every drive, make sure that all occupants
wear their safety belts. Airbags complement the
safety belt as an additional safety device, but
they do not represent a substitute.

Closing

Make sure you hear the latch plate engage in
the belt buckle.
The upper belt anchor is suitable for adults of
any stature as long as the seat is adjusted prop-
erly, refer to page

Opening

Grasp the belt firmly.

Press the red button in the buckle.

Guide the belt into its reel.

'Fasten safety belts' reminder for front

seats

The indicator lamp comes on and an
acoustic signal sounds. Check
whether the safety belt has been fas-
tened correctly.

The 'Fasten safety belts' reminder is issued as
long as the driver's safety belt has not been fas-
tened. The 'Fasten safety belts' reminder is also
activated at road speeds above approx. 5 mph
or 8 km/h if the front passenger's safety belt is

not fastened, if heavy objects are placed on the
front passenger seat, or if driver or front pas-
senger unfasten their safety belts.

Damage to safety belts

If the safety belts are damaged or
stressed in an accident: have the belt sys-

tem, including any belt tensioners or child-
restraint systems, replaced and the belt
anchors checked. Have this work done only by
your BMW center or at a workshop that works
according to BMW repair procedures with cor-
respondingly trained personnel. Otherwise, it is
not guaranteed that the safety devices will func-
tion properly.

Belt hand-over

The concept

The belt hand-over makes it easier for you to
fasten your safety belt. When you close the
door and switch on the ignition or turn the igni-
tion key to the radio-ready position, the belt
hand-over extends automatically and presents
the belt in a position that is convenient for fas-
tening it around you. After you have fastened
your safety belt, the belt hand-over retracts to
its original position.

Even if you have not yet fastened your safety
belt, the belt hand-over will retract if you:

wait for more than approx. one minute

open the corresponding door

start to drive.

Closing the respective door reactivates the belt
hand-over if the ignition or radio-readiness are
on.

ba5_E9293_EUR_US.book Seite 36 Donnerstag, 4. Mai 2006 1:08 13

Front passenger's seat

The belt hand-over will extend only if the seat is
occupied and after the front passenger's door is
closed.

Mirrors

Exterior mirrors

The front passenger's mirror is more convex
than the driver's mirror. The objects seen in the
mirror are closer than they appear. Do not
gauge your distance from traffic behind you on
the basis of what you see in the mirror; other-
wise there is an increased risk of an accident.

1 Adjustments
2 Switching to the other mirror or automatic

curb monitor

3 Folding mirrors in and out

The settings for the exterior mirrors are stored
for the remote control currently in use

, refer to

Personal Profile, page

. The stored positions

are called up automatically when the vehicle is
unlocked.

Manual adjustment

The mirrors can also be adjusted manually:
press the edge of the glass.

Folding mirrors in and out*

At driving speeds up to approx. 12 mph/
20 km/h, you can fold the mirrors in and out by
pressing button

3. This could be beneficial in

narrow streets, for example, or for moving mir-
rors that were folded in manually back out to
their correct positions. Mirrors that were folded

in are folded out automatically at a speed of
approx. 25 mph/40 km/h.

Before entering an automatic car wash,
fold in the exterior mirrors by hand or with

button

3, to prevent them from being damaged

due to the width of the vehicle.

Automatic heating

At outside temperatures below a certain limit,
both exterior mirrors are automatically heated
while the engine is running or the ignition
switched on.

Passenger-side mirror tilt function –

automatic curb monitor*

Activating

Push the switch to the position for the
driver's-side mirror, arrow

Engage reverse gear or move the selector
lever to position R.
The glass of the mirror on the passenger
side tilts slightly down. This allows the
driver to see the area immediately adjacent
to the vehicle, e.g. a curb when parking.

Deactivating

Push the switch to the position for the front pas-
senger's mirror, arrow

ba5_E9293_EUR_US.book Seite 37 Donnerstag, 4. Mai 2006 1:08 13

Adjustments

Interior rearview mirror

Turn the knob to reduce glare from the head-
lamps of cars behind you when driving at night.
Automatically dimming mirrors, refer to
page

Steering wheel

Adjustments

Do not adjust the steering wheel position
while the car is in motion, or an accident

may result from any unexpected movement.

Fold the lever down.

Move the steering wheel to the preferred
height and angle to suit your seated posi-
tion.

Swing the lever back up.

Do not use force to swing the lever
back up, otherwise the mechanism

will be damaged.

Electric steering wheel lock

The steering wheel locks or unlocks automati-
cally when the remote control is removed or
inserted, refer to page

ba5_E9293_EUR_US.book Seite 38 Donnerstag, 4. Mai 2006 1:08 13

Transporting children safely

The right place for children

Do not leave children unattended in the
vehicle, otherwise they could endanger

themselves and/or other persons by opening
the doors, for example.

Children always in the rear

Accident research has shown that the safest
place for children is on the rear seats.

Children under the age of 13 or smaller
than 5 ft/150 cm may be transported only

in the rear in suitable child-restraint systems
appropriate for their age, weight and size. Oth-
erwise there is an increased risk of injury in the
event of an accident.

Children 13 years of age or older must be buck-
led in with a safety belt as soon as there no
longer is any child-restraint system that is
appropriate for their age, size and weight.
Both rear seats in your vehicle meet the recom-
mendations of the SAE J1819 standard for
safely mounting child-restraint systems in
motor vehicles.

Exception for front passenger seat

Should it be necessary to use a child-
restraint system on the front passenger

seat, the front-passenger airbags must be
deactivated. Otherwise, a child traveling on that
seat will be at a significant risk of injury if the air-
bags are triggered off, even with a child-
restraint system. Your BMW center will be glad
to advise you.

For more information on automatic deactivation
of the front passenger airbags refer to page

Installing child-restraint

systems

Observe the child-restraint system man-
ufacturer's instructions when selecting,

installing and using child-restraint systems.

Otherwise the protective effect may be dimin-
ished.

On the front passenger's seat

Before installing a child-restraint system
on the front passenger's seat, make sure

that the front and side airbags for the front pas-
senger are deactivated, otherwise there is an
increased risk of injury if the airbags deploy.

Backrest width*

The backrest width of the front passenger
seat must be adjusted to its widest set-

ting. Otherwise the child seat cannot rest com-
pletely against the backrest. After installing the
child seat, do not call up any seat memory posi-
tions. Otherwise there is a risk of injury.

Adjust the backrest width to its widest set-
ting, refer to page

Install the child seat.

Child seat security

The rear safety belts and the front passenger's
safety belt can be prevented from being pulled
out in order to fasten child-restraint systems.

To lock the safety belt

Secure the child-restraint system with the
belt.

Pull the belt strap all the way out.

Allow the belt strap to retract and pull it taut
against the child-restraint system.

The safety belt is locked.

ba5_E9293_EUR_US.book Seite 39 Donnerstag, 4. Mai 2006 1:08 13

Transporting children safely

To unlock the safety belt

Open the belt buckle

Remove the child-restraint system.

Allow the safety belt strap to retract all the
way.

Child-restraint system with tether
strap

There are two additional anchors for child-
restraint systems with tether straps, see
arrows.

Placement of the tether strap

1 Forward driving direction
2 Head restraint
3 Attaching clip
4 Child restraint anchor fitting
5 Rear window shelf
6 Seat back
7 Tether strap
Fold the anchors upward before using them.

Push the head restraint upward.

Guide the tether strap between the head
restraint holders.

Use the hook to clip the tether strap to the
anchor.

Push the head restraint into its lowermost
position.

Pull the tether strap taut.

LATCH child-restraint fixing

system

LATCH: Lower Anchors and Tethers for CHil-
dren.

When installing and using LATCH child-
restraint systems, comply with the sys-

tem manufacturer's operating and safety
instructions.

Before installing the child seat, pull the belt out
of the area for the child-restraint fixing system.

Rear seats

The anchor points for the lower LATCH
anchors are located behind the labeled protec-
tive caps.

Make sure that the two lower LATCH
anchors are properly engaged and that

the child-restraint system rests firmly against
the seat backrest.

ba5_E9293_EUR_US.book Seite 40 Donnerstag, 4. Mai 2006 1:08 13

Driving

Ignition lock

Insert the remote control all the way into the
ignition lock.

Radio readiness switches on.
Individual electrical consumers can operate.

The electric steering wheel lock disen-
gages audibly.

Insert the remote control into the ignition
lock before you move the vehicle, other-

wise the electric steering wheel lock will not dis-
engage and you will not be able to steer the
car.

Removing the remote control from the

ignition lock

Press the remote control in briefly; it is ejected
part of the way.
At the same time:

The ignition switches off if it was on before-
hand.

The electric steering wheel lock engages
audibly.

Automatic transmission

You cannot take out the remote control unless
the selector lever is in the P position: interlock.

Start/stop button

Each time the start/stop button is pressed,
radio readiness or the ignition is switched on or
off.

Briefly pressing the start/stop button
while the brake or clutch is depressed

starts the engine.

Radio readiness

Individual electrical consumers can operate.
The time and the outside temperature are dis-
played in the instrument cluster, refer to
page

Radio readiness is switched off automatically:

When the remote control is removed from
the ignition lock

In cars with convenient access

, by touch-

ing the surface above the door lock, refer to
Locking on page

Ignition on

All electrical consumers can operate. The
odometer and trip odometer are displayed in
the instrument cluster, refer to page

When the engine is off, please turn off the
ignition and any unnecessary electrical

consumers in order to preserve the battery.

Radio readiness and ignition off

All indicator and warning lamps as well as dis-
plays in the instrument cluster go out.

ba5_E9293_EUR_US.book Seite 41 Donnerstag, 4. Mai 2006 1:08 13

Driving

Starting the engine

Do not run the engine in closed rooms,
otherwise the inhalation of toxic exhaust

gases can cause unconsciousness and death.
The exhaust gases contain carbon monoxide,
an odorless and colorless, but highly toxic gas.
Never leave an unattended vehicle with the
engine running, otherwise such a vehicle repre-
sents a potential safety hazard.
Before leaving the car with the engine running,
place the transmission in idle or move the
selector lever to position P and apply the hand-
brake to prevent the car from moving.

When starting the engine, do not press the
accelerator pedal.
Do not allow the engine to warm up by leaving it
running while the vehicle remains stationary.
Instead, begin to drive at a moderate engine
speed.

Do not depress either the brake or the
clutch until you are ready to start the

engine. The engine is started when you briefly
touch the start/stop button and depress the
brake if the car has automatic transmission, or
the clutch if the car has manual transmission.

Manual transmission

Apply the handbrake.

Depress the clutch and shift to idle position.

Briefly press the start/stop button.

The starter operates automatically for a certain
time, and stops automatically as soon as the
engine has started.

Automatic transmission

Depress the brake.

Move the selector lever to position P or N.

Briefly press the start/stop button.

The starter operates automatically for a certain
time, and stops automatically as soon as the
engine has started.

Special starting conditions

In the following situations, press the accelerator
pedal halfway down when starting the engine:

If the engine does not start on the first
attempt, for instance when it is extremely
hot or cold.

If the engine is started at very low tempera-
tures, below approx. + 5

7/–156, at high

altitudes above approx. 3,300 ft/1,000 m.

Avoid frequent starting in quick succes-
sion or repeated start attempts in which

the engine does not start. Otherwise, the fuel is
not burned or inadequately burned and there is
a danger of overheating and damaging the cat-
alytic converter.

Switching off the engine

Always take the remote control with you
when you leave the vehicle.

When parking on a downhill incline, apply the
handbrake, otherwise the vehicle could roll
away.

Manual transmission

With the car at a standstill, briefly press the
start/stop button.

Shift into first gear or reverse.

Apply the handbrake.

Automatic transmission

With the car at a standstill, move the selec-
tor lever to position P.

Briefly press the start/stop button.

Apply the handbrake.

ba5_E9293_EUR_US.book Seite 42 Donnerstag, 4. Mai 2006 1:08 13

Handbrake

The handbrake is primarily intended to prevent
the vehicle from rolling while parked; it brakes
the rear wheels.

Indicator lamp

The indicator lamp is lit, and when you
drive off an acoustic signal sounds in
addition. The handbrake is still applied.
Indicator lamp for Canadian models.

Applying

The lever locks in position automatically.

Releasing

Pull slightly upwards, press the button and
lower the lever.

In exceptional cases, if the handbrake has
to be used to slow or stop the car, do not

pull the lever up too hard. In doing so, continu-
ously press the button of the handbrake lever.
Otherwise, too violent an application of the
handbrake can lock up the rear wheels and
cause the rear of the car to swerve.

To prevent corrosion and one-sided brak-
ing action, occasionally apply the hand-

brake lightly when the vehicle is slowly coming
to a stop if the traffic conditions are suitable.
The brake lamps do not light up when the hand-
brake is applied.

Manual transmission

When shifting into 5th or 6th gear, press
the gearshift lever to the right. Otherwise

the engine could be damaged if you inadvert-
ently shift into 3rd or 4th gear.

Reverse gear

Select only when the vehicle is stationary.
When the gearshift lever is pressed to the left, a
slight resistance has to be overcome.

Automatic transmission with

Steptronic*

In addition to fully automatic operation, you can
also shift manually with the Steptronic, refer to
page

Vehicle parking

To prevent the vehicle from rolling,
always select position P and apply the

handbrake before leaving the vehicle with the
engine running.

Disengaging the remote control

In order to remove the remote control from the
ignition lock, you must first move the selector
lever to position P and switch off the engine:
interlock.

Selector lever positions

P R N D M/S + –

ba5_E9293_EUR_US.book Seite 43 Donnerstag, 4. Mai 2006 1:08 13

Была ли эта страница вам полезна?

Да!Нет

BMW 325Ci Coupe (2006 year). Instruction — part 2

Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.