Hummer H3. Manual — part 1354
Electrical Information Reference
Circuit Testing
Connector Repairs
Testing for Intermittent Conditions and Poor Connections
Wiring Repairs
Scan Tool Reference
Scan Tool Data List
Circuit/System Testing
1. Ignition OFF, disconnect the EOP switch.
2. Ignition OFF, test for less than 1 ohm of resistance between the low reference circuit and
ground.
If greater than 1 ohm, test the low reference circuit for an open/high resistance. If the
circuit tests normal, replace the PCM.
3. Ignition ON, install a 3-amp fused jumper wire between the signal circuit and the low
reference circuit. Verify the scan tool Engine Oil Pressure Switch parameter is Low.
If not Low, test the signal circuit of the EOP switch for an open/high resistance. If the
circuit tests normal replace the PCM.
4. If all circuits test normal, test or replace the EOP switch.
Repair Procedures
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
Engine Oil Pressure Sensor and/or Switch Replacement
Control Module References for the PCM replacement, setup and programming
SYMPTOMS - DISPLAYS AND GAGES
1. Perform the Diagnostic System Check - Vehicle before using the Symptom Tables in
order to verify that all of the following are true:
There are no DTCs set.
IMPORTANT: The following steps must be completed before using the symptom
tables.
2007 Hummer H3
2007 ACCESSORIES & EQUIPMENT Displays and Gages - H3
The control modules can communicate via the serial data link.
2. Review the system operation in order to familiarize yourself with the system functions.
Refer to the following:
Instrument Cluster Description and Operation
Indicator/Warning Message Description and Operation
Driver Information Center (DIC) Description and Operation
Audible Warnings Description and Operation
Door Ajar Indicator Description and Operation
Compass Calibration and Magnetic Variance
Visual/Physical Inspection
Inspect for aftermarket devices which could affect the operation of the Instrument Cluster or
Audible Warning Systems. Refer to Checking Aftermarket Accessories .
Inspect the easily accessible or visible system components for obvious damage or conditions
which could cause the symptom.
Inspect the applicable reservoir for the proper fluid level related to the indicator or
message.
Verify that the indicators work properly during the displays test.
Intermittent
Faulty electrical connections or wiring may be the cause of intermittent conditions. Refer to
Testing for Intermittent Conditions and Poor Connections .
Symptom List
Refer to a symptom diagnostic procedure from the following list in order to diagnose the
symptom:
Gages
Engine Coolant Temperature Gage Inaccurate or Inoperative
Fuel Gage Inaccurate or Inoperative
Speedometer and/or Odometer Inaccurate or Inoperative
Tachometer Inaccurate or Inoperative
Indicators
2007 Hummer H3
2007 ACCESSORIES & EQUIPMENT Displays and Gages - H3
ABS Indicator Always On
ABS Indicator Inoperative
Air Bag Indicator Circuit Malfunction
Brake Warning Indicator Malfunction
Charge Indicator Always On
Charge Indicator Inoperative
Door Ajar Indicator Malfunction
Engine Oil Pressure Indicator Always On
Engine Overheated Indicator Always On
Fog Lamp Indicator Inoperative
High Beam Indicator Always On
High Beam Indicator Inoperative
Malfunction Indicator Lamp (MIL) Always On for the 3.7L engine
Malfunction Indicator Lamp (MIL) Inoperative for the 3.7L engine
Mirror Compass Display Inoperative or Inaccurate
Mirrors - Temperature Display Inaccurate
Mirrors - Temperature Displays SC or OC
Passenger Presence System Indicator Circuit Malfunction
Security Indicator Malfunction
Seat Belt Indicator Circuit Malfunction - Driver
Seat Belt Indicator Circuit Malfunction - Passenger
Service Indicator Always On
Service Indicator Inoperative
Traction Off Indicator Inoperative
Transfer Case Shift Control Switch Indicator Always On - Two or More
Transfer Case Shift Control Switch Indicator Flashes, then Returns to Previous
Mode
Transfer Case Shift Control Switch Indicator Inoperative - One or More
Turn Signal Lamps and/or Indicators Always On or Flashing
Turn Signal Lamps and/or Indicators Inoperative
Instrument Cluster Dimming
2007 Hummer H3
2007 ACCESSORIES & EQUIPMENT Displays and Gages - H3
Interior Backlighting Does Not Dim
Interior Backlighting Inoperative
Odometer
Odometer Trip/Reset Switch Inoperative
Audible Warning
Chime Always On
Chime Inoperative
CHIME ALWAYS ON
Diagnostic Instructions
Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
Review Strategy Based Diagnosis for an overview of the diagnostic approach.
Diagnostic Procedure Instructions provides an overview of each diagnostic category.
Circuit/System Description
The radio generates the audible warning through the left front speaker. The radio receives audible
warning requests via GMLAN serial data from the body control module (BCM).
Reference Information
Schematic Reference
Instrument Cluster Schematics
Body Control System Schematics
Connector End View Reference
Displays and Gages Connector End Views
Data Communication Connector End Views
Electrical Information Reference
Circuit Testing
Connector Repairs
2007 Hummer H3
2007 ACCESSORIES & EQUIPMENT Displays and Gages - H3
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст