Hummer H3. Manual — part 629
SCAN TOOL DATA LIST
Scan Tool Data List
Solenoid Tests
Left Front
Isolation
Valve
Left Front
Dump Valve
Right Front
Isolation
Valve
Right Front
Dump Valve
Rear Isolation
Valve
Rear Dump
Valve
EBCM and BPMV.
Dump Valve Solenoid Test Procedure
1. Apply the parking brake fully.
2. Start the engine and allow the engine to idle.
3. Select the desired Dump Valve Solenoid Test
on the scan tool.
4. Apply the brake and maintain steady pressure
on the brake pedal.
5. Command the solenoid On and verify that the
brake pedal drops to the floor.
Isolation Valve Solenoid Test Procedure
1. Apply the parking brake fully.
2. Start the engine and allow the engine to idle.
3. Select the desired Isolation Valve Solenoid
Test on the scan tool.
4. Apply the brake with very light pressure only
enough to close the brake switch.
5. Command the solenoid On and then
immediately apply firm and steady pressure to
the brake pedal.
6. The EBCM automatically de-energizes the
solenoid after about 3 seconds. When this
occurs, verify that the brake pedal drops about
2.2 cm (1 inch).
Scan Tool Parameter
Data List
Units Displayed
Typical Data
Value
Ignition ON, Engine OFF and Brake Released
4WD Status
ABS
Two wheel drive/Four wheel
drive
4WD
ABS Active
ABS/VSES
Yes/No
No
2007 Hummer H3
2007 BRAKES Antilock Brake System - H3
ABS Lamp Command
ABS/VSES
On/Off
Off
ABS Pump Motor
ABS/VSES
On/Off
Off
ABS Relay Command
ABS/VSES
On/Off
ON
ABS Stop State
VSES
On/Off
Off
Accum. Pressure Sensor
ABS/VSES
MPa/psi
Varies
Analog Steering Position
Sensor
VSES
°
Varies
Battery Voltage
ABS
Volts
12.0 Volts
Brake Fluid Level
ABS/VSES
OK/Low
OK
Brake Switch Status
ABS/VSES
On/Off
Off
Brake Warning Lamp
Command
VSES
On/Off
Off
Delivered Torque
ABS
%
Varies
Digital Steering Position
Sensor
VSES
°
Varies
Lateral Accelerometer Input
VSES
m/s -ft/s
0
Left Front Wheel Speed
ABS
km/h or mph
0 km/h/0 mph
Left Rear Wheel Speed
ABS
km/h or mph
0 km/h/0 mph
LF Dump Valve Command
ABS/VSES
On/Off
Off
LF Iso. Valve Command
ABS/VSES
On/Off
Off
LR Dump Valve Command
ABS/VSES
On/Off
Off
LR Iso. Valve Command
ABS/VSES
On/Off
Off
Longitudinal Accelerometer
Sensor Signal
ABS
m/s
2
or ft/s
2
Varies
Master Cylinder Pressure
Sensor Input
ABS/VSES
kPa or Psi
0
Requested Torque
ABS
%
90%
Reverse Switch
ABS/VSES
On/Off
Off
RF Dump Valve Command
ABS/VSES
On/Off
Off
RF Iso. Valve Command
ABS/VSES
On/Off
Off
RR Dump Valve Command
ABS/VSES
On/Off
Off
RR Iso. Valve Command
ABS/VSES
On/Off
Off
RF Dump Valve Command
ABS/VSES
On/Off
Off
RF ISO Valve Command
ABS/VSES
On/Off
Off
Right Front Wheel Speed
ABS
km/h or mph
0 km/h/0 mph
2007 Hummer H3
2007 BRAKES Antilock Brake System - H3
SCAN TOOL DATA DEFINITIONS
The ABS scan tool data definitions contain a brief description of all ABS related parameters
available on the scan tool. The parameters available on the scan tool are listed below in
alphanumeric order.
4WD Status
The scan tool displays if the vehicle is in 2 wheel drive or 4 wheel drive.
ABS Active
The scan tool displays if the ABS system is performing antilock braking.
ABS Lamp Command
The scan tool displays the commanded state of the ABS warning indicator.
Right Rear Wheel Speed
ABS
km/h or mph
0 km/h/0 mph
Stability System Active
VSES
Yes/No
No
Stability System Enabled
VSES
Yes/No
Yes
System Configuration
ABS/VSES
Invalid/Not Deturmined/Non-
VSES Auto/Non-VSES
Manual/VSES
Varies
System Voltage
VSES
Volts
12 V
TCS Status/EBCM - TCS
Active
ABS/VSES
Yes/No
No
TCS Status/PCM - TCS
Active
ABS/VSES
Yes/No
No
Traction Control Equipped
ABS
Invalid/Disabled/Enabled or
N/A
Enabled
Traction Control Switch
ABS
Yes/No
Yes
Transmission Type
ABS/VSES
Invalid/Not
Determined/Automatic/Manual
Varies
VSES Control Switch
VSES
Invalid/Disabled/Enabled or
N/A
Enabled
VSES Equipped
VSES
Yes/No
Varies
Yaw Rate Sensor Input
VSES
°/sec
0
2007 Hummer H3
2007 BRAKES Antilock Brake System - H3
ABS Pump Motor
The scan tool displays On/Off. The scan tool displays On when the ABS pump motor is
commanded on.
ABS Relay Command
The scan tool displays the commanded state of the ABS system relay.
ABS Stop State
The scan tool displays if the ABS system is performing antilock braking.
Accum. Pressure Sensor
The scan tool displays brake fluid pressure stored in the accumulator.
Analog Steering Position Sensor
The scan tool displays the analog steering position angle in degrees.
Battery Voltage
The scan tool displays the approximate voltage supplied by the battery and charging system.
Brake Fluid Level
The scan tool displays if the brake fluid is Low or OK.
Brake Switch Status
The scan tool displays the state of the brake switch.
Brake Warning Lamp Command
The scan tool displays ON when the EBCM requests illumination of the brake warning
indicator.
Delivered Torque
The scan tool displays between 11% and 90%. The PCM provides the percentage of engine
torque that is currently applied to the wheels. The lower the percentage the less torque
2007 Hummer H3
2007 BRAKES Antilock Brake System - H3
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст