Hummer H3. Manual — part 1061
Connections
Go to Step 3
3
Is the door ajar indicator ON all the time?
Go to Step 4
Go to Step 8
4
1. Install a scan tool.
2. Close all of the doors.
3. Turn ON the ignition, with the engine
OFF.
4. With a scan tool, observe the Driver
Door Ajar Sw. and the Passenger
Door Ajar Sw. parameters in the
body control module (BCM) data
list.
Does the scan tool display Door Ajar for
either of the parameters?
Go to Step 5
Go to Step 19
5
Is the Driver Door Ajar sw. parameter
displaying Door Ajar?
Go to Step 6
Go to Step 7
6
1. With a scan tool, observe the Driver
Door Ajar Sw. parameter in the
BCM data list.
2. Disconnect the driver ajar switch
assembly harness connector.
Does the scan tool display Door Closed?
Go to Step 20
Go to Step 15
7
1. With a scan tool, observe the
Passenger Door Ajar Sw. parameter
in the BCM data list.
2. Disconnect each of the passenger ajar
switch assembly harness connectors,
one at a time.
Does the scan tool display Door Closed
when any of the harness connectors is
disconnected?
Go to Step 20
Go to Step 16
8
Is the door ajar indicator inoperative from
the driver door?
Go to Step 9
Go to Step 12
1. Install a scan tool.
2. Turn ON the ignition, with the engine
2007 Hummer H3
2007 ACCESSORIES & EQUIPMENT Vehicle Access - H3
9
OFF.
3. Disconnect the driver ajar switch
assembly harness connector.
4. Connect a 3-amp fused jumper wire
between the left front door ajar
switch signal circuit of the driver ajar
switch assembly harness connector
and a good ground.
5. With a scan tool, observe the Driver
Door Ajar Sw. parameter in the
BCM data list.
Does the scan tool display Door Ajar?
Go to Step 10
Go to Step 17
10
Is the door ajar indicator illuminated?
Go to Step 11
Go to Step 19
11
1. Connect a 3-amp fused jumper wire
between the left front door ajar
switch signal circuit of the driver ajar
switch assembly harness connector
and the ground circuit of the driver
ajar switch assembly harness
connector.
2. With a scan tool, observe the Driver
Door Ajar Sw. parameter in the
BCM data list.
Does the scan tool display Door Ajar?
Go to Step 20
Go to Step 22
12
1. Install a scan tool.
2. Turn ON the ignition, with the engine
OFF.
3. Disconnect the appropriate passenger
ajar switch assembly harness
connector.
4. Connect a 3-amp fused jumper wire
between the door ajar switch signal
circuit of the appropriate passenger
ajar switch assembly harness
connector and a good ground.
2007 Hummer H3
2007 ACCESSORIES & EQUIPMENT Vehicle Access - H3
5. With a scan tool, observe the
Passenger Door Ajar Sw. parameter
in the BCM data list.
Does the scan tool display Door Ajar?
Go to Step 13
Go to Step 18
13
Is the door ajar indicator illuminated?
Go to Step 14
Go to Step 19
14
1. Connect a 3-amp fused jumper wire
between the door ajar switch signal
circuit of the appropriate passenger
ajar switch assembly harness
connector and the ground circuit of
the appropriate passenger ajar switch
assembly harness connector.
2. With a scan tool, observe the
Passenger Door Ajar Sw. parameter
in the BCM data list.
Does the scan tool display Door Ajar?
Go to Step 20
Go to Step 22
15
Test the left front door ajar switch signal
circuit for a short to ground. Refer to
Circuit Testing and Wiring Repairs .
Did you find and correct the condition?
Go to Step 26
Go to Step 21
16
Test the appropriate door ajar switch
signal circuit for a short to ground. Refer
to Circuit Testing and Wiring Repairs .
Did you find and correct the condition?
Go to Step 26
Go to Step 21
17
Test the left front door ajar switch signal
circuit for an open. Refer to Circuit
Testing and Wiring Repairs .
Did you find and correct the condition?
Go to Step 26
Go to Step 21
18
Test the appropriate door ajar switch
signal circuit for an open. Refer to Circuit
Testing and Wiring Repairs .
Did you find and correct the condition?
Go to Step 26
Go to Step 21
19
Inspect for poor connections at the harness
connector of the instrument panel cluster
(IPC). Refer to Testing for Intermittent
Conditions and Poor Connections and
2007 Hummer H3
2007 ACCESSORIES & EQUIPMENT Vehicle Access - H3
POWER DOOR LOCKS INOPERATIVE
Power Door Locks Inoperative
Connector Repairs .
Did you find and correct the condition?
Go to Step 26
Go to Step 23
20
Inspect for poor connections at the harness
connector of the appropriate door ajar
switch. Refer to Testing for Intermittent
Conditions and Poor Connections and
Connector Repairs .
Did you find and correct the condition?
Go to Step 26
Go to Step 24
21
Inspect for poor connections at the harness
connector of the BCM. Refer to Testing
for Intermittent Conditions and Poor
Connections and Connector Repairs .
Did you find and correct the condition?
Go to Step 26
Go to Step 25
22
Repair the open in the appropriate ground
circuit. Refer to Wiring Repairs and
Connector Repairs .
Did you find and correct the condition?
Go to Step 26
-
23
Replace the IPC. Refer to Control
Module References for replacement,
setup and programming.
Did you complete the replacement?
Go to Step 26
-
24
Replace the appropriate ajar switch
assembly.
Did you complete the replacement?
Go to Step 26
-
25
Replace the BCM. Refer to Control
Module References for replacement,
setup and programming.
Did you complete the replacement?
Go to Step 26
-
26
Operate the system in order to verify the
repair.
Did you correct the condition?
System OK
Go to Step 2
Step
Action
Yes
No
Schematic Reference: Door Lock/Indicator Schematics
Connector End View Reference: Vehicle Access Connector End Views
2007 Hummer H3
2007 ACCESSORIES & EQUIPMENT Vehicle Access - H3
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст