Hummer H3. Manual — part 735
SECOND/THIRD GEAR ONLY OR FIRST/FOURTH GEARS ONLY
Second/Third Gears Only or First/Fourth Gears Only
NO FIRST OR SECOND GEAR/NO THIRD OR FOURTH GEAR
No 1st or 2nd/No 3rd or 4th
NO SECOND GEAR, NO FOURTH GEAR AND NO REVERSE GEAR
No Second Gear, No Fourth Gear and No Reverse Gear
checkballs
Input Housing Assembly
(620-621, 646-655)
3-4 clutch or forward clutch plates worn
Excessive clutch plate travel
Cut or damaged 3-4 clutch or forward clutch piston seals
Porosity in input clutch housing or piston
3-4 clutch piston checkball stuck, damaged or not sealing
Restricted apply passages
Forward clutch piston retainer and ball assembly not
seating
Sealing balls loose or missing
Input housing (621) cracked or broken
Case (103)
3rd accumulator retainer and ball assembly not seating
2-4 Servo Assembly (13-28) 2nd apply piston seals missing, cut or damaged
Checks
Causes
1-2 Shift Solenoid Valve
(367A)
Sediment is in the valves
The electrical connection is faulty
Damaged seal
Checks
Causes
2-3 Shift Solenoid Valve
(367B)
Sediment is in the valves
The electrical connection is faulty
Damaged seal
Checks
Causes
Reaction Sun Shell (670)
Broken spline on reaction sun shell/replace shell.
2007 Hummer H3
2007 TRANSMISSION Automatic Transmission - 4L60-E/4L65-E/4L70-E - H3
THIRD GEAR ONLY
Third Gear Only
3-2 FLARE OR TIE-UP
3-2 Flare or Tie-Up
NO 3-4 SHIFT, SLIPS OR ROUGH 3-4 SHIFT
No 3-4 Shift/Slipping or Rough 3-4 Shift
Checks
Causes
System Voltage
12 volts not supplied to transmission
Electrical short (pinched solenoid wire)
Solenoid not grounded
Checks
Causes
3-2 Shift Solenoid Valve
Assembly (394)
Shorted or damaged
Contamination
Damaged Seal
Check ball not seating
Checks
Causes
Oil Pump Assembly (4)
Pump cover retainer and ball assembly omitted or
damaged
Faces not flat
Valve Body Assembly (60)
Valves stuck
2-3 Shift valve train
Accumulator valve
1-2 Shift valve train
3-2 Shift solenoid valve assembly
Spacer plate or gaskets incorrect, mispositioned or
damaged
2-4 Servo Assembly (13-28)
Incorrect band apply pin
Missing or damaged servo seals
Porosity in piston, cover or case
Damaged piston seal grooves
2007 Hummer H3
2007 TRANSMISSION Automatic Transmission - 4L60-E/4L65-E/4L70-E - H3
NO REVERSE OR SLIPS IN REVERSE
No Reverse or Slips in Reverse
Plugged or missing orifice cup plug
Case (103)
3rd Accumulator retainer and ball assembly leaking
Porosity in 3-4 accumulator piston or bore
3-4 Accumulator piston seal or seal grooves damaged
Plugged or missing orifice cup plug
Restricted oil passage
Input Housing Assembly
(621)
Refer to No 2-3 Shift or 2-3 Shift Slips, Rough or
Hunting.
2-4 Band Assembly (602)
Worn or misassembled
Checks
Causes
Input Housing Assembly
(602)
3-4 Apply ring stuck in applied position
Forward clutch not releasing
Turbine shaft seals missing, cut or damaged
Manual Valve Link (89)
Disconnected
Valve Body Assembly (60)
2-3 Shift valve stuck
Manual linkage not adjusted
Spacer plate and gaskets incorrect, mispositioned or
damaged
Lo overrun valve stuck
Orificed cup plug restricted, missing or damaged
Reverse Input Clutch
Assembly (605-614)
Clutch plate worn
Reverse input housing and drum assembly cracked at
weld
Clutch plate retaining ring out of groove
Return spring assembly retaining ring out of groove
Seals cut or damaged
Restricted apply passage
Porosity in piston
Belleville plate installed incorrectly
2007 Hummer H3
2007 TRANSMISSION Automatic Transmission - 4L60-E/4L65-E/4L70-E - H3
NO PART THROTTLE OR DELAYED DOWNSHIFTS
No Part Throttle or Delayed Downshifts
Excessive clutch plate travel
Oversized housing
Lo and Reverse Clutch
(694-696)
Clutch plates worn
Porosity in piston
Seals damaged
Return spring assembly retaining ring mispositioned
Restricted apply passage
Reaction Sun Shell (670)
Broken spline on reaction sun shell/replace shell
Checks
Causes
Input Housing Assembly
(621)
3-4 Apply ring stuck in applied position
Forward clutch not releasing
Turbine shaft seals missing, cut or damaged
Manual Valve Link (89)
Disconnected
Valve Body Assembly (60)
2-3 Shift valve stuck
Manual linkage not adjusted
Spacer plate and gaskets incorrect, mispositioned or
damaged
Lo overrun valve stuck
Orificed cup plug restricted, missing or damaged
Reverse Input Clutch
Assembly (606-614)
Clutch plate worn
Reverse input housing and drum assembly cracked at
weld
Clutch plate retaining ring out of groove
Return spring assembly retaining ring out of groove
Seals cut or damaged
Restricted apply passage
Porosity in piston
Belleville plate installed incorrectly
Excessive clutch plate travel
2007 Hummer H3
2007 TRANSMISSION Automatic Transmission - 4L60-E/4L65-E/4L70-E - H3
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст