Hummer H3. Manual — part 1708
Does the scan tool display On?
Go to Step 7
Go to Step 6
6
1. Turn OFF the ignition.
2. Disconnect the harness that contains
the rear defogger switch signal circuit
connector of the BCM.
3. Turn ON the ignition, with the engine
OFF.
4. Connect a test lamp between battery
voltage and the rear defogger switch
signal circuit at the BCM connector.
5. Depress the rear defogger switch.
Does the test lamp illuminate?
Go to Step 16
Go to Step 10
7
1. Connect a test lamp between the
defogger relay control circuit and
ground.
2. Depress the rear window defogger
switch.
Does the test lamp illuminate?
Go to Step 13
Go to Step 11
8
1. With a scan tool, select from the
Special Functions the Rear Defogger
Relay in the BCM output controls.
2. Command the Rear Defogger Relay
ON and OFF.
Do you hear a click when you command
the relay ON and OFF?
Go to Step 12
Go to Step 9
9
Connect a test lamp between the supply
voltage circuit of the rear defog relay
switched input and a good ground.
Does the test lamp illuminate?
Go to Step 11
Go to Step 12
10
Test the rear defogger switch signal circuit
and the rear defogger switch ground circuit
of the HVAC control module for an open
or short to voltage. Refer to Circuit
Testing and Wiring Repairs .
2007 Hummer H3
2007 ACCESSORIES & EQUIPMENT Fixed and Moveable Windows - H3
Did you find and correct the condition?
Go to Step 20
Go to Step 12
11
Test for an open or high resistance in the
rear defogger relay control circuit and
ground circuit. Refer to Circuit Testing
and Wiring Repairs .
Did you find and correct the condition?
Go to Step 21
Go to Step 16
12
Test the supply voltage circuit for the
following conditions:
An open
A high resistance
A short to ground
Refer to Circuit Testing and Wiring
Repairs .
Did you find and correct the condition?
Go to Step 21
Go to Step 13
13
Test for the following in the rear defogger
indicator supply voltage circuit:
An open
A high resistance
A short to ground
Refer to Circuit Testing and Wiring
Repairs .
Did you find and correct the condition?
Go to Step 21
Go to Step 15
14
Inspect for poor connections at the rear
defog relay. Refer to Testing for
Intermittent Conditions and Poor
Connections and Connector Repairs .
Did you find and correct the condition?
Go to Step 21
Go to Step 18
15
Inspect for poor connections at the harness
connector of the HVAC control module.
Refer to Testing for Intermittent
Conditions and Poor Connections and
Connector Repairs .
2007 Hummer H3
2007 ACCESSORIES & EQUIPMENT Fixed and Moveable Windows - H3
POWER WINDOW INOPERATIVE - DRIVER DOOR
Power Window Inoperative - Driver Door
Did you find and correct the condition?
Go to Step 21
Go to Step 19
16
Inspect for poor connections at the harness
connector of the BCM. Refer to Testing
for Intermittent Conditions and Poor
Connections and Connector Repairs .
Did you find and correct the condition?
Go to Step 21
Go to Step 20
17
Repair an open or high resistance in the
ground circuit of the rear defogger. Refer
to Wiring Repairs .
Did you complete the repair?
Go to Step 21
-
18
Replace the rear defog relay. Refer to
Relay Replacement (Attached to Wire
Harness) or Relay Replacement (Within
an Electrical Center) .
Did you complete the replacement?
Go to Step 21
-
19
Replace the HVAC control module. Refer
to Control Module References for
replacement, setup and programming.
Did you complete the replacement?
Go to Step 21
-
20
Replace the BCM. Refer to Control
Module References for replacement,
setup and programming.
Did you complete the replacement?
Go to Step 21
-
21
Operate the system in order to verify the
repair.
Did you correct the condition?
System OK
Go to Step 2
Step
Action
Yes
No
Schematic Reference: Moveable Window Schematics
Connector End View Reference: Window Systems Connector End Views
1
Did you perform the Diagnostic System
Check - Vehicle?
Go to Step 2
Go to
Diagnostic
System Check -
Vehicle
Verify that the driver door power window
Go to Testing
2007 Hummer H3
2007 ACCESSORIES & EQUIPMENT Fixed and Moveable Windows - H3
2
is inoperative.
Does the driver door power window
operate normally?
for Intermittent
Conditions and
Poor
Connections
Go to Step 3
3
Are the power door locks inoperative also?
Go to Step 6
Go to Step 4
4
1. Turn OFF the ignition.
2. Disconnect the driver window motor.
3. Turn ON the ignition, with the engine
OFF.
4. Probe the power window motor left
front up control circuit of the driver
window motor harness connector with
a test lamp that is connected to a good
ground.
5. Activate the driver window switch to
the UP position.
Does the test lamp illuminate?
Go to Step 5
Go to Step 7
5
1. Connect a test lamp between the
power window motor left front up
control circuit of the driver window
motor harness connector and the
power window motor left front down
control circuit of the driver window
motor harness connector.
2. Activate the driver window switch to
the DOWN position.
Does the test lamp illuminate?
Go to Step 10
Go to Step 8
6
Test the battery positive voltage circuit of
the drivers switch assembly for a short to
ground or an open. Refer to Circuit
Testing and Wiring Repairs .
Did you find and correct the condition?
Go to Step 14
Go to Step 9
7
Test the power window motor left front up
control circuit of the driver window motor
for an open. Refer to Circuit Testing and
2007 Hummer H3
2007 ACCESSORIES & EQUIPMENT Fixed and Moveable Windows - H3
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст