Hummer H3. Manual — part 1660
(Canadian P/N 88861801), to the transfer case via the speed sensor hole.
13. Install the speed sensor to the top of the transfer case and connect the electrical connector.
Tighten: Tighten the speed sensor to 17 N.m (13 lb ft).
14. Lower the vehicle.
TRANSFER CASE MOTOR/ENCODER REPLACEMENT
Fig. 16: Transfer Case Motor/Encoder Replacement
Courtesy of GENERAL MOTORS CORP.
Transfer Case Motor/Encoder Replacement
NOTE:
Refer to Component Fastener Tightening Notice .
Callout
Component Name
Fastener Tightening Specifications: Refer to Fastener Tightening Specifications .
NOTE:
Refer to Fastener Notice .
2007 Hummer H3
2007 TRANSMISSION Transfer Case - BW 4493/4494 - H3
TRANSFER CASE SPEED SENSOR REPLACEMENT
Fig. 17: Transfer Case Speed Sensor Replacement
Courtesy of GENERAL MOTORS CORP.
Preliminary Procedures
1. Raise the vehicle. Refer to Lifting and Jacking the Vehicle .
2. Remove the transfer case shield. Refer to Transfer Case Shield Replacement.
1
Encoder Motor Electrical Connector
2
Mounting Encoder Motor Bolt (Qty: 3)
Tighten: 10 N.m (89 lb in)
3
Encoder Motor Mounting Bracket Bolt
Tighten: 10 N.m (89 lb in)
4
Encoder Assembly Motor
5
Encoder Motor Bracket Nut
Tighten: 5 N.m (44 lb in)
6
Encoder Motor Bracket
2007 Hummer H3
2007 TRANSMISSION Transfer Case - BW 4493/4494 - H3
Transfer Case Speed Sensor Replacement
TRANSFER CASE OUTPUT SHAFT SEAL REPLACEMENT - FRONT
Fig. 18: Transfer Case Output Shaft Seal Replacement - Front
Courtesy of GENERAL MOTORS CORP.
Transfer Case Output Shaft Seal Replacement - Front
Callout
Component Name
Fastener Tightening Specifications: Refer to Fastener Tightening
Specifications.Preliminary Procedure: Remove the transfer case shield. Refer to
Transfer Case Shield Replacement.
NOTE:
Refer to Fastener Notice .
1
Sensor, Speed
Tip: Disconnect the electrical connector.
Tighten: 17 N.m (13 lb ft)
Callout
Component Name
2007 Hummer H3
2007 TRANSMISSION Transfer Case - BW 4493/4494 - H3
TRANSFER CASE OUTPUT SHAFT SEAL REPLACEMENT - REAR
Fastener Tightening Specifications: Refer to Fastener Tightening Specifications.
Preliminary Procedure
1. Raise the vehicle. Refer to Lifting and Jacking the Vehicle .
2. Remove the front propeller shaft. Refer to Front Propeller Shaft Replacement .
Tools Required
J 8614-01 Flange and Pulley Holding Tool
J 42738 Front Output Shaft Seal Installer. See Special Tools.
NOTE:
Refer to Fastener Notice .
1
Nut, Drive Flange Retaining (Qty: 1)
Tip: Using the J 8614-01 , remove the retaining nut.
Tighten: 319 N.m (235 lb ft)
2
Washer, Drive Flange (Qty: 1)
3
Seal, Drive Flange Washer (Qty: 1)
4
Flange, Drive Flange
5
Seal, Front Output Shaft
Tip:
1. Using the appropriate tool, remove the seal.
2. Using the J 42738 , install the Front Output Shaft Seal Installer. See
Special Tools.
2007 Hummer H3
2007 TRANSMISSION Transfer Case - BW 4493/4494 - H3
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст