Hummer H3. Manual — part 1127
Diagnostic Aids
Recommended Action:
Correct F-Term short low condition.
Clear the codes.
Cycle the ignition.
If a fault condition persists, replace the module.
DTC B1492
IMPORTANT: You must cycle the ignition after clearing the DTC to turn OFF the
DIC message of Service Charging System.
IMPORTANT: You must cycle the ignition after clearing the DTC to turn OFF the
DIC message of Service Charging System and turn OFF the
battery indicator.
Step
Action
Values
Yes
No
Schematic Reference: Starting and Charging Schematics
Connector End View Reference: Engine Electrical Connector End Views
1
Did you perform the Diagnostic
System Check - Vehicle?
-
Go to Step 2
Go to
Diagnostic
System Check
- Vehicle
2
1. Start engine and idle.
2. With a scan tool, observe the
Generator F-Terminal Signal
parameter in the powertrain
control module (PCM) data
display.
Is the Generator F-Terminal Signal
data less than the specified value?
5%
Go to Step 3
Testing for
Intermittent
Conditions
and Poor
Connections
3
Disconnect the generator battery
control module harness connector
Is the Generator F-Terminal Signal
parameter still less than the
5%
2007 Hummer H3
2007 ENGINE Engine Electrical - H3
DTC B1516
Circuit Description
The generator battery control module monitors its internal battery current sensor for many
charging system operations. When the values of the battery current sensor go out of range, DTC
B1516 will set.
DTC Descriptor
This diagnostic procedure supports the following DTC:
specified value?
Go to Step 5 Go to Step 4
4
Inspect for poor connections at the
harness connector of the generator
battery control module. Refer to
Testing for Intermittent
Conditions and Poor Connections
and Connector Repairs .
Did you find and correct the
condition?
-
Go to Step 7 Go to Step 6
5
Repair the short to ground of the
generator field duty cycle control
circuit.
Did you find and correct the
condition?
-
Go to Step 7 Go to Step 6
6
Replace the generator battery
control module. Refer to Control
Module References for
replacement, setup and
programming.
Did you complete the replacement?
-
Go to Step 7
-
7
1. Use the scan tool in order to
clear the DTC.
2. Operate the vehicle within the
Conditions for Running the
DTC, as specified in the
supporting text.
Does the DTC reset?
-
Go to Step 2
System OK
2007 Hummer H3
2007 ENGINE Engine Electrical - H3
DTC B1516 Battery Current Sensor Performance
Conditions for Running the DTC
Vehicle in RUN mode and Engine Run Flag is True.
This diagnostic shall be run every 50 ms.
Conditions for Setting the DTC
The duty cycle of the internal battery current sensor is less than 2 percent duty cycle or greater
than 98 percent duty cycle for greater than 240 seconds.
Action Taken When the DTC Sets
The filtered battery current is set to 0.1 amp.
The generator field control circuit duty cycle is set to 100 percent, battery voltage defaults
to 13.8 volts.
The generator battery control module will request the driver information center (DIC)
message of Service Charging System. The battery indicator remains OFF.
Conditions for Clearing the DTC
The duty cycle of the internal battery current sensor is greater than 2 percent duty cycle or less
than 98 percent duty cycle.
Diagnostic Aids
Recommended Action:
Clear the codes.
Cycle the ignition.
DTC B1516
IMPORTANT: You must cycle the ignition after clearing the DTC to turn OFF the
DIC message of Service Charging System.
Step
Action
Yes
No
Schematic Reference: Starting and Charging Schematics
Connector End View Reference: Engine Electrical Connector End Views
Did you perform the Diagnostic System
Check - Vehicle?
Go to
Diagnostic
2007 Hummer H3
2007 ENGINE Engine Electrical - H3
DTC B1566
Circuit Description
The generator battery control module monitors its internal battery current sensor for many
charging system operations. When the polarity of the battery current is sensed, DTC B1566 will
set.
DTC Descriptor
This diagnostic procedure supports the following DTC:
DTC B1566 Current Sensor Polarity Check
Conditions for Running the DTC
Vehicle in RUN mode and Engine Run Flag is True.
This diagnostic shall be run every 50 ms.
Conditions for Setting the DTC
1
Go to Step 2
System Check -
Vehicle
2
1. Install a scan tool.
2. Clear DTC.
3. Cycle ignition.
Does DTC B1516 reset?
Go to Step 3
Go to Testing
for Intermittent
Conditions and
Poor
Connections
3
Replace the generator battery control
module. Refer to Control Module
References for replacement, setup and
programming.
Did you complete the replacement?
Go to Step 4
-
4
1. Use the scan tool in order to clear the
DTC.
2. Operate the vehicle within the
Conditions for Running the DTC, as
specified in the supporting text.
Does the DTC reset?
Go to Step 2
System OK
2007 Hummer H3
2007 ENGINE Engine Electrical - H3
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст