Hummer H3. Manual — part 1131
Use the test adapters that are provided with the J 42000 or GM P/N 12303040 terminal
adapters. See Special Tools. If the adapters that are provided with the J 42000 require
replacement, use GM P/N 12303040. See Special Tools. Any other adapter may not
contact the correct areas of the battery terminal, causing a resistance that may result in an
invalid battery test result.
Battery Inspection/Test (Non-HP2)
Step
Action
Value(s)
Yes
No
CAUTION:
Refer to Battery Disconnect Caution .
1
Inspect the battery for a cracked,
broken or damaged case, which may
be indicated by battery acid leakage.
Is the battery OK?
-
Go to Step 2
Go to Step
19
2
Compare the cold cranking amperage
(CCA) and reserve capacity (RC) of
the battery to the original battery or
original equipment (OE)
specification. Refer to Battery
Usage.
Does the battery meet or exceed the
specifications?
-
Go to Step 3
Go to Step
19
3
Does the hydrometer display a
yellow dot?
-
Go to Step 4 Go to Step 5
4
Tap the hydrometer lightly on top
with the handle of a small
screwdriver in order to dislodge any
air bubbles inside the battery.
Does the hydrometer still display a
yellow dot?
-
Go to Step
19
Go to Step 5
5
1. Turn OFF the ignition.
2. Attempt to rotate the negative
battery cable connector
clockwise with light finger
pressure.
Does the negative connector rotate?
-
Go to Step 6 Go to Step 7
Use a torque wrench in order to
2007 Hummer H3
2007 ENGINE Engine Electrical - H3
6
verify the torque to loosen the
negative battery terminal bolt.
Is the torque above the specified
value?
10 N.m (88
lb in)
Go to Step 8 Go to Step 7
7
Disconnect the negative battery
cable.
Is the cable disconnected?
-
Go to Step 9
-
8
1. Disconnect the negative battery
cable.
2. Inspect for the following
conditions and repair as
needed:
The cable bolt is too long
or deformed at the end.
There is foreign material
present inside the nut in
the battery terminal.
Damage to the battery
terminal face or cable
connector ring.
Is the repair complete?
-
Go to Step 9
-
9
Rotate the positive battery cable
connector clockwise with light finger
pressure.
Does the positive connector rotate?
-
Go to Step
10
Go to Step
11
10
Use a torque wrench in order to
verify the torque to loosen the
positive battery terminal bolt.
Is the torque above the specified
value?
10 N.m (88
lb in)
Go to Step
12
Go to Step
11
11
Disconnect the positive battery cable.
Is the cable disconnected?
-
Go to Step
13
-
1. Disconnect the positive battery
cable.
2. Inspect for the following
conditions and repair as
2007 Hummer H3
2007 ENGINE Engine Electrical - H3
12
needed:
The cable bolt is too long
or deformed at the end.
There is foreign material
present inside the nut in
the battery terminal.
Damage to the battery
terminal face or cable
connector ring.
Is the repair complete?
-
Go to Step
13
-
13
1. Clean and wire brush the lead
face of both battery terminals
and the metal contact rings in
both cable connectors.
2. Remove the bolts from the
cable connectors in order to
provide access to the connector
rings as needed.
3. If either of the battery terminals
or the cable rings are
excessively damaged or
corroded, replace as needed.
Are the metal connecting parts clean
and in good condition?
-
Go to Step
14
-
14
1. Connect the positive battery
cable to the battery positive
terminal.
2. Tighten the cable bolt to the
specified value.
Is the cable bolt properly tightened?
15 N.m (11
lb ft)
Go to Step
15
-
15
1. Connect the negative battery
cable to the battery negative
terminal.
2. Tighten the cable bolt to the
15 N.m (11
lb ft)
2007 Hummer H3
2007 ENGINE Engine Electrical - H3
BATTERY CHARGING
Tools Required
specified value.
Is the cable bolt properly tightened?
Go to Step
16
-
16
1. Install the J 42000 Battery
Tester. See Special Tools.
2. Follow the directions supplied
with the tester.
3. Follow any direction displayed
on the tester.
Did the tester pass the battery?
IMPORTANT:
Ensure that all of the electrical loads are
turned OFF.
-
Go to Step
17
Go to Step
18
17
1. Press the CODE button on the J
42000 . See Special Tools.
2. For warranty purposes, write
the displayed code on the repair
order.
Did you complete this action?
-
Battery OK
-
18
1. Press the CODE button on the J
42000 . See Special Tools.
2. For warranty purposes, write
the displayed code on the repair
order.
3. Replace the battery. Refer to
Battery Replacement.
Did you complete the replacement?
-
Battery OK
-
19
Replace the battery. Refer to
Battery Replacement.
Did you complete the replacement?
-
Battery OK
-
2007 Hummer H3
2007 ENGINE Engine Electrical - H3
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст