Hummer H3. Manual — part 723
Fig. 3: View Of Torque Converter Hub In Engine Crankshaft
Courtesy of GENERAL MOTORS CORP.
3. Align the torque converter hub (2) in the engine crankshaft (3) and install the torque
converter to flywheel bolts.
4. Lower the vehicle.
2007 Hummer H3
2007 TRANSMISSION Automatic Transmission - 4L60-E/4L65-E/4L70-E - H3
5. With the engine at idle speed and the transmission in PARK or NEUTRAL, observe the
vibration. Refer to Noise and Vibration Analysis.
Repeat this procedure until you obtain the best possible balance.
6. Install the transmission converter cover bolts and the cover.
NOISE AND VIBRATION ANALYSIS
A noise or vibration that is noticeable when the vehicle is in motion MAY NOT be the result of
the transmission.
If noise or vibration is noticeable in PARK and NEUTRAL with the engine at idle, but is less
noticeable as RPM increases, the cause may be from poor engine performance.
Vibration may also be caused by a small amount of water inside the converter.
Inspect the tires for the following conditions:
Uneven wear
Imbalance
Mixed sizes
Mixed radial and bias ply
Inspect the suspension components for the following conditions:
Alignment wear or damage
Loose fasteners
Driveline damage or wear
Inspect the engine and transmission mounts for damage and loose bolts.
Inspect the transmission case mounting holes for the following conditions:
Missing bolts, nuts and studs
Stripped threads
Cracks
Inspect the flywheel for the following conditions:
Missing or loose bolts
Cracks
Imbalance
Inspect the torque converter for the following conditions:
Missing or loose bolts or lugs
2007 Hummer H3
2007 TRANSMISSION Automatic Transmission - 4L60-E/4L65-E/4L70-E - H3
Missing or loose balance weights
Imbalance caused by heat distortion or fluid contamination
CLUTCH PLATE DIAGNOSIS
Composition Plates
Dry the plates and inspect the plates for the following conditions:
Pitting
Flaking
Delamination-splitting or separation of bonded clutch material
Wear
Glazing
Cracking
Charring
Chips or metal particles embedded in the lining
Replace a composition plate which shows any of these conditions.
Steel Plates
Wipe the plates dry and check the plates for heat discoloration. If the surfaces are smooth, even if
color smear is indicated, you can reuse the plate. If the plate is discolored with heat spots or if the
surface is scuffed, replace the plate.
Causes of Burned Clutch Plates
The following conditions can result in a burned clutch plate:
Incorrect usage of clutch or apply plates
Engine coolant or water in the transmission fluid
A cracked clutch piston
Damaged or missing seals
Low line pressure
Valve body conditions
The valve body face is not flat.
Porosity is between channels.
2007 Hummer H3
2007 TRANSMISSION Automatic Transmission - 4L60-E/4L65-E/4L70-E - H3
The valve bushing clips are improperly installed.
The checkballs are misplaced.
The Teflon® seal rings are worn or damaged.
ENGINE COOLANT/WATER IN TRANSMISSION
If antifreeze or water has entered the transmission, perform the following:
1. Disassemble the transmission.
2. Replace all of the rubber type seals (the coolant will attack the seal material which will
cause leakage).
3. Replace the composition-faced clutch plate assemblies and the 2-4 band assembly (the
facing material may separate from the steel center portion).
4. Replace all of the nylon parts (washers).
5. Replace the torque converter.
6. Thoroughly clean and rebuild the transmission, using new gaskets (bonded and non bonded)
and oil filter.
7. Flush the cooler lines after the transmission cooler has been properly repaired or replaced.
FLUID LEAK DIAGNOSIS
General Method
1. Verify that the leak is transmission fluid.
2. Thoroughly clean the suspected leak area.
3. Operate the vehicle for 24 km (15 mi) or until normal operating temperatures are reached.
4. Park the vehicle over clean paper or cardboard.
5. Shut OFF the engine.
6. Look for fluid spots on the paper.
7. Make the necessary repairs.
Powder Method
1. Thoroughly clean the suspected leak area with solvent.
NOTE:
The antifreeze or water will deteriorate the seals, gaskets and the
glue that bonds the clutch material to the pressure plate. Both
conditions may cause damage to the transmission.
2007 Hummer H3
2007 TRANSMISSION Automatic Transmission - 4L60-E/4L65-E/4L70-E - H3
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст