Hummer H3. Manual — part 1644
207
Shift Fork Shaft
208
Input Gear Thrust Bearing
209
Mainshaft
210
Oil Pump
211
Oil Pump Hose Clamp
212
Oil Pump Hose
213
Oil Pump Screen
214
Upper Center Bearing Support Thrust Washer
215
Bearing
216
Snap Ring
217
Center Bearing Support
218
Lower Center Support Bearing Thrust Washer
219
Shift Cam
220
Shift Shaft Torsional Spring
221
Shift Shaft Spacer
222
Shift Shaft
223
Inner Lockup Hub
224
Lockup Mode Shift Collar Assembly
225
Lockup Mode Shift Fork
226
Shift Fork Shaft Spring
227
Drive Sprocket Bushing
228
Drive Sprocket
229
Drive Chain
230
Front Output Sun Gear
231
Planetary Differential Assembly
232
Rear Output Shaft Thrust Washer
233
Rear Output Sun Gear
234
Mainshaft Rear Support Bushing
235
Rear Output Shaft
236
Rear Output Shaft Bearing Outer Retaining Ring
237
Rear Output Shaft Bearing
238
Rear Output Shaft Bearing Retaining Ring
239
Speed Sensor Tone Wheel
240
Front Output Shaft Rear Bearing
241
Driven Gear
242
2007 Hummer H3
2007 TRANSMISSION Transfer Case - BW 4493/4494 - H3
DIAGNOSTIC INFORMATION AND PROCEDURES
DIAGNOSTIC CODE INDEX
DIAGNOSTIC CODE INDEX
DIAGNOSTIC STARTING POINT - TRANSFER CASE
Begin the system diagnosis with the Diagnostic System Check - Vehicle . The Diagnostic
System Check will provide the following information:
The identification of the control module or modules that command the system.
The ability of the control module or modules to communicate through the serial data circuit.
The identification of any stored diagnostic trouble codes (DTCs) and the status of the codes.
The use of the Diagnostic System Check - Vehicle will identify the correct procedure for
diagnosing the system and where the procedure is located.
SCAN TOOL OUTPUT CONTROLS
Scan Tool Output Controls
Front Output Shaft
243
Front Output Shaft Front Bearing
DTC
Description
DTC B0790
Transfer Case Neutral Indicator Circuit Malfunction
DTC B2725
ATC Mode Switch Circuit Malfunction
DTC C0306
Motor A or B Circuit Malfunction
DTC C0327
Encoder Circuit Malfunction
DTC C0329
Encoder Signal Circuit Low
DTC C0359
Four Wheel Drive Low Range (4WD low) Discrete Output
Circuit Malfunction
DTC C0550
ECU Malfunction
Scan Tool Output
Control
Additional Menu
Selections
Description
Refer to the scan tool manual for complete scan tool operating instructions.
4WD High
Indicator Light
-
This function allows the technician to command the
4WD high indicator light, within the transfer case
2007 Hummer H3
2007 TRANSMISSION Transfer Case - BW 4493/4494 - H3
SCAN TOOL DATA LIST
Scan Tool Data List
shift control switch, on or off.
4WD High Lock
Indicator Light
-
This function allows the technician to command the
4WD high lock indicator light, within the transfer
case shift control switch, on or off.
4WD Low Lock
Indicator Light
-
This function allows the technician to command the
4WD low lock indicator light, within the transfer
case shift control switch, on or off.
Differential Lock
Indicator Light
-
This function allows the technician to command the
differential indicator light, within the transfer case
shift control switch, on or off.
Motor A Driver -
High
-
This function allows the technician to request the
high side driver for the motor control A circuit, thus
allowing the technician to test the circuit and the
transfer case shift control module for their ability to
provide battery voltage to the motor.
Motor A Driver -
Low
-
This function allows the technician to request the
low side driver for the motor control A circuit, thus
allowing the technician to test the circuit and the
transfer case shift control module for their ability to
provide a ground path for the motor.
Motor B Driver -
High
-
This function allows the technician to request the
high side driver for the motor control B circuit, thus
allowing the technician to test the circuit and the
transfer case shift control module for their ability to
provide battery voltage to the motor.
Motor B Driver -
Low
-
This function allows the technician to request the
low side driver for the motor control B circuit, thus
allowing the technician to test the circuit and the
transfer case shift control module for their ability to
provide a ground path for the motor.
Neutral Indicator
Light
-
This function allows the technician to command the
neutral indicator light, within the transfer case shift
control switch, on or off.
Scan Tool Parameter
Data List
Units Displayed
Typical Data
Value
2007 Hummer H3
2007 TRANSMISSION Transfer Case - BW 4493/4494 - H3
Engine is at Idle, Upper Radiator Hose is Hot, Closed Throttle, Gear is in Park or
Neutral and Accessories are OFF.
4WD High Indicator Light
Transfer Case
Data
On/Off
Off
4WD High Lock Indicator Light
Transfer Case
Data
On/Off
Off
4WD Low Active
Transfer Case
Data
Yes/No
No
4WD Low Lock Indicator Light
Transfer Case
Data
On/Off
Off
ATC Application
Transfer Case
Data
Number
Number
Encoder Circuit A
Transfer Case
Data
On/Off
On
Encoder Circuit B
Transfer Case
Data
On/Off
On
Encoder Circuit C
Transfer Case
Data
On/Off
On
Encoder Circuit P
Transfer Case
Data
On/Off
On
Encoder Gear Position
Transfer Case
Data
4WD High/4WD
Low/AWD
4WD High
Encoder Supply Voltage
Transfer Case
Data
Volts
2.55
Ign. Cycles Since Last Current
DTC
Transfer Case
Data
Count
Varies
Mode Switch Return Voltage
Transfer Case
Data
Volts
0-5 V
Mode Switch Selected
Transfer Case
Data
Transfer Case
Mode
Inactive
Motor A High Side Driver Status
Transfer Case
Data
On/Off
NO
Motor A Low Side Driver Status
Transfer Case
Data
On/Off
NO
Motor B High Side Driver Status
Transfer Case
Data
On/Off
NO
Motor B Low Side Driver Status
Transfer Case
On/Off
NO
2007 Hummer H3
2007 TRANSMISSION Transfer Case - BW 4493/4494 - H3
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст