Hummer H3. Manual — part 1058
Passenger Door Lock and Window Switch Connector Terminal Identification
DIAGNOSTIC INFORMATION AND PROCEDURES
DIAGNOSTIC CODE INDEX
DIAGNOSTIC CODE INDEX
DIAGNOSTIC STARTING POINT - VEHICLE ACCESS
Begin the system diagnosis with the Diagnostic System Check - Vehicle . The Diagnostic
System Check will provide the following information:
Core/Insulation Crimp: 4/A
Release Tool/Test Probe: 15315247/J-35616-18 (BK)
Pin
Wire Color
Circuit No.
Function
1-2
-
-
Not Used
3
D-BU
245
Passenger Door Lock Switch Unlock
Control
4
L-BU
244
Passenger Door Lock Switch Lock
Control
5
BK
1550
Ground
6
BN
9
Park Lamp Supply Voltage
7
D-BU
1307
Power Window Master Switch
Lockout Signal
8
TN
167
Power Window Master Switch Right
Front Down Signal
9
L-BU
166
Power Window Master Switch Right
Front Up Signal
10
BN
667
Power Window Motor Right Front
Down Control
11
YE
443
Accessory Voltage
12
D-BU
666
Power Window Motor Right Front Up
Control
DTC
Description
DTC B3142 or B3143
Unlock Switch Circuit
DTC B3152 or B3153
Lock Switch Circuit
2007 Hummer H3
2007 ACCESSORIES & EQUIPMENT Vehicle Access - H3
The identification of the control modules which command the system
The ability of the control modules to communicate through the serial data circuit
The identification of any stored diagnostic trouble codes (DTCs) and their status
The use of the Diagnostic System Check will identify the correct procedure for diagnosing the
system and where the procedure is located.
SCAN TOOL DATA DEFINITIONS
All Door Unlock Relay
The scan tool displays On/Off. The door unlock relay output from the body control module
(BCM), where the relay actuating to the unlock position is displayed as On.
Battery Voltage Signal
The scan tool displays 9.0-15.0 volts. The state of the battery voltage supplied to the BCM.
Calibration ID
The scan tool displays the calibration ID number of the BCM.
Door Lock Relay
The scan tool displays On/Off. The door lock relay output from the BCM, where the relay
actuating to the lock position is displayed as On.
Door Lock Relay Fdbk.
The scan tool displays Active/Inactive. The door lock relay feedback input to the BCM,
where the relay being actuated is displayed as Active.
Driver Door Ajar Sw.
The scan tool displays Door Closed/Door Ajar. The driver door ajar switch input to the
BCM, where a closed switch is displayed as Door Ajar.
End Model Part Number
The scan tool displays the end model part number of the BCM.
2007 Hummer H3
2007 ACCESSORIES & EQUIPMENT Vehicle Access - H3
Julian Date of Build
The scan tool displays the date the BCM was built.
Passenger Door Ajar Sw.
The scan tool displays Door Closed/Door Ajar. The passenger door ajar switch input to the
BCM, where a closed switch is displayed as Door Ajar.
Software Part Number
The scan tool displays the BCMs software revision part number.
Year Module Build
The scan tool displays the year the BCM was built.
SCAN TOOL DATA LIST
Body Control Module Scan Tool Data List
SCAN TOOL OUTPUT CONTROLS
Scan Tool Parameter
Data List
Units Displayed
Typical Data
Value
Operating Conditions: Key ON, Engine OFF.
All Door Unlock Relay
Outputs
On/Off
Off
Battery Voltage Signal
Data
Volts
12.8 Volts
Calibration ID
ID Information
Numerical
XXXX
Door Lock Relay
Outputs
On/Off
Off
Door Lock Relay Fdbk.
Inputs
Active/Inactive
Inactive
Driver Door Ajar Sw.
Inputs
Door Closed/Door
Ajar
Door Closed
End Model Part Number
ID Information
Numerical
XXXX
Julian Date of Build
ID Information
Numerical
XXX
Passenger Door Ajar Sw.
Inputs
Door Closed/Door
Ajar
Door Closed
Software Part Number
ID Information
Numerical
XXXX
Year Module Built
ID Information
Numerical
XXXX
2007 Hummer H3
2007 ACCESSORIES & EQUIPMENT Vehicle Access - H3
Body Control Module
DTC B3142 OR B3143
Circuit Description
The body control module (BCM) provides an output to the driver switch assembly through the
door unlock control circuit for controlling automatic door unlock, anti-lockout and keyless entry
unlock functions.
DTC Descriptors
This diagnostic procedure supports the following DTCs:
DTC B3142 Unlock Switch Circuit Low
DTC B3143 Unlock Switch Circuit High
Conditions for Setting the DTC
The BCM detects a short to ground on the door unlock control circuit for greater than 60
seconds.
The BCM detects a short to battery on the door unlock control circuit for greater than 1
second.
Action Taken When the DTC Sets
The BCM stores DTC B3142 or B3143 in memory.
The BCM will disable the output and all operations of the output until the fault no longer
exists.
Conditions for Clearing the DTC
The BCM no longer detects the short to ground on the door unlock control circuit for
Scan Tool
Output Control
Additional Menu
Selection(s)
Description
Door Lock
Door Lock Test
The body control module (BCM) actuates all of the
door lock actuators for approximately 5 seconds
when you select On. All of the doors should lock.
Unlock Doors
Door Lock Test
The BCM actuates all of the door lock actuators for
approximately 5 seconds when you select On. All of
the doors should unlock.
2007 Hummer H3
2007 ACCESSORIES & EQUIPMENT Vehicle Access - H3
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст