Hummer H3. Manual — part 1186
DTC B1025, B1035, B1045 OR B1055
Circuit Description
When the radio is powered up, the radio supplies low level audio signals to the speakers. If the
vehicle is equipped with an audio amplifier, the amplifier will boost the signal sent to the
speakers. The radio tests the speaker output circuits for a short to voltage or ground.
DTC Descriptors
This diagnostic procedure supports the following DTCs:
DTC B1025 Audio Output 1 (Left Front) Circuit
DTC B1035 Audio Output 2 (Right Front) Circuit
DTC B1045 Audio Output 3 (Left Rear) Circuit
DTC B1055 Audio Output 4 (Right Rear) Circuit
Conditions for Running the DTC
The test is performed when the radio switches from OFF to ON. The radio will continue to test
for the fault once every 0.5 seconds.
Conditions for Setting the DTC
1
Did you perform the Diagnostic System
Check - Vehicle?
Go to Step 2
Go to
Diagnostic
System Check -
Vehicle
2
1. Install a scan tool.
2. Turn ON the ignition, with the
engine OFF.
3. With a scan tool, configure the
module to the vehicle.
Does the DTC reset?
Go to Step 3
System OK
3
Replace the module. Refer to Control
Module References for replacement,
setup and programming.
Did you complete the replacement?
System OK
-
2007 Hummer H3
2007 ACCESSORIES AND EQUIPMENT Cellular, Entertainment and Navigation - H3
The radio sets a current status for this DTC when a short to ground or voltage is detected on any
of the speaker channels for 1.5 seconds.
Action Taken When the DTC Sets
No sound is present from one or more of the speakers.
Conditions for Clearing the DTC
The condition is no longer present for 5 seconds.
Test Description
The number below refers to the step number on the diagnostic table.
2: The DTC descriptor indicates which speaker output circuit set the DTC.
DTC B1025, B1035, B1045 or B1055
Step
Action
Yes
No
Schematic Reference: Radio/Navigation System Schematics
Connector End View Reference: Entertainment/Communication Connector End
Views
1
Did you perform the Diagnostic System
Check - Vehicle?
Go to Step 2
Go to
Diagnostic
System Check -
Vehicle
2
1. Disconnect the appropriate speaker.
2. Turn ON the radio.
3. Test the speaker output circuit for a
short to ground or short to voltage.
Refer to Circuit Testing and Wiring
Repairs .
Did you find and correct the condition?
Go to Step 6
Go to Step 3
3
Inspect for poor connections at the harness
connector of the speaker. Refer to Testing
for Intermittent Conditions and Poor
Connections and Connector Repairs .
Did you find and correct the condition?
Go to Step 6
Go to Step 4
Inspect for poor connections at the harness
2007 Hummer H3
2007 ACCESSORIES AND EQUIPMENT Cellular, Entertainment and Navigation - H3
DTC B1259
Diagnostic Instructions
Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
Review Strategy Based Diagnosis for an overview of the diagnostic approach.
Diagnostic Procedure Instructions provide an overview of each diagnostic category.
DTC Descriptor
DTC B1259
Antenna Ground Circuit
Diagnostic Fault Information
DTC B1259
Circuit/System Description
The antenna signal circuit is a coaxial cable that carries the radio signal information received by
the antenna. The antenna cable also provides a path for DC current for powering the antenna.
Conditions for Running the DTC
4
connector of the radio. Refer to Testing
for Intermittent Conditions and Poor
Connections and Connector Repairs .
Did you find and correct the condition?
Go to Step 6
Go to Step 5
5
Replace the radio. Refer to Control
Module References for replacement, setup
and programming.
Did you complete the replacement?
Go to Step 6
-
6
Operate the system in order to verify the
repair.
Did you correct the condition?
System OK
Go to Step 2
Circuit
Short to
Ground
Open/High
Resistance
Short to
Voltage
Signal
Performance
Antenna Signal
1
1
1
-
1. Sets code B1259
2007 Hummer H3
2007 ACCESSORIES AND EQUIPMENT Cellular, Entertainment and Navigation - H3
This test is run every 300 milliseconds.
Conditions for Setting the DTC
The digital radio receiver (DRR) detects an antenna fault.
Action Taken When the DTC Sets
The radio displays "No XM Signal" or "Check Antenna".
Conditions for Clearing the DTC
The condition must be corrected.
The DTC clears after 100 malfunction-free ignition cycles.
Reference Information
Schematic Reference
Radio/Navigation System Schematics
Connector End View Reference
Entertainment/Communication Connector End Views
Description and Operation
Radio/Audio System Description and Operation
Electrical Information Reference
Circuit Testing
Connector Repairs
Testing for Intermittent Conditions and Poor Connections
Wiring Repairs
Special Tools Required
EL-48028 Digital Radio Test Antenna
Circuit/System Testing
1. Ignition OFF, disconnect the antenna coax from the digital radio receiver (DRR). Connect
the test antenna to the DRR.
2007 Hummer H3
2007 ACCESSORIES AND EQUIPMENT Cellular, Entertainment and Navigation - H3
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст