Hummer H3. Manual — part 1427
TAIL LAMPS INOPERATIVE
Tail Lamps Inoperative
11
Refer to Wiring Repairs , Tail Lamp
Bulb Replacement or High Mount Stop
Lamp Replacement.
Is the repair complete?
Go to Step 14
-
12
Replace the stop lamp switch. Refer to
Stop Lamp Switch Replacement.
Did you complete the replacement?
Go to Step 14
-
13
Replace the BCM. Refer to Control
Module References for replacement,
setup and programming.
Did you complete the replacement?
Go to Step 14
-
14
Operate the system in order to verify the
repair.
Did you correct the condition?
System OK
Go to Step 3
Step
Action
Yes
No
Schematic Reference: Exterior Lights Schematics
Connector End View Reference: Lighting Systems Connector End Views
1
Did you perform the Diagnostic System
Check - Vehicle?
Go to Step 2
Go to
Diagnostic
System Check -
Vehicle
2
Verify that the tail lamps are inoperative.
Do the tail lamps operate normally?
Go to Testing
for Intermittent
Conditions and
Poor
Connections
Go to Step 3
3
Inspect the appropriate fuse for the
inoperative lamps in the underhood fuse
block.
Is the fuse open?
Go to Step 5
Go to Step 4
4
Inspect the inoperative bulbs/sockets for
open or shorted filaments/terminals.
Does any lamp have an open or shorted
filament/terminals?
Go to Step 7
Go to Step 6
2007 Hummer H3
2007 ACCESSORIES & EQUIPMENT Lighting - H3
TURN SIGNAL LAMPS AND/OR INDICATORS ALWAYS ON OR FLASHING
Turn Signal Lamps and/or Indicators Always On or Flashing
5
Repair the short to ground in the inoperative
tail lamps supply voltage circuit or license
lamp supply voltage circuit. Refer to
Wiring Repairs .
Did you complete the repair?
Go to Step 8
-
6
Repair the open or high resistance in the
inoperative tail lamps supply voltage circuit
or ground circuit. Refer to Wiring
Repairs .
Did you complete the repair?
Go to Step 8
-
7
Replace the defective bulb/socket. Refer to
Tail Lamp Bulb Replacement.
Did you complete the repair?
Go to Step 8
-
8
Operate the system in order to verify the
repair.
Did you correct the condition?
System OK
Go to Step 3
Step
Action
Yes
No
Schematic Reference: Exterior Lights Schematics
Connector End View Reference: Lighting Systems Connector End Views or Data
Communication Connector End Views
1
Did you perform the Diagnostic System
Check - Vehicle?
Go to Step
Go to
Diagnostic
System Check -
Vehicle
2
Verify that the turn signal lamps and/or
indicators are always ON or flashing.
Do the turn signal lamps operate normally?
Go to Testing
for Intermittent
Conditions and
Poor
Connections
Go to Step 3
3
Inspect the affected bulb/socket for an
internal short, poor terminal contact or a
shorted filament.
Was a problem found?
Go to Step 8
Go to Step 4
Disconnect the multifunction turn signal
2007 Hummer H3
2007 ACCESSORIES & EQUIPMENT Lighting - H3
TURN SIGNAL LAMPS AND/OR INDICATORS INOPERATIVE
Turn Signal Lamps and/or Indicators Inoperative
4
switch.
Do the affected turn signals and indicators
still illuminate?
Go to Step 5
Go to Step 6
5
Test for a high resistance or short to ground
in the turn signal switch signal circuit.
Did you find and correct the condition?
Go to Step 11
Go to Step 7
6
Inspect for poor connections at the
multifunction turn signal switch. Refer to
Circuit Testing and Wiring Repairs .
Did you find and correct the condition?
Go to Step 11
Go to Step 9
7
Inspect for poor connections at the body
control module (BCM). Refer to Circuit
Testing and Wiring Repairs .
Did you find and correct the condition?
Go to Step 11
Go to Step 10
8
Replace or repair the affected bulb/socket.
Refer to Daytime Running Lamp Bulb
Replacement or Tail Lamp Bulb
Replacement.
Did you complete the repair?
Go to Step 11
-
9
Replace the turn signal/multifunction
switch. Refer to Turn Signal
Multifunction Switch Replacement .
Did you complete the repair?
Go to Step 11
-
10
Replace the BCM. Refer to Control
Module References for replacement,
setup and programming.
Did you complete the repair?
Go to Step 11
-
11
1. Use the scan tool in order to clear any
induced DTCs.
2. Operate the system in order to verify
the repair.
Did you correct the condition?
System OK
Go to Step 3
Step
Action
Yes
No
2007 Hummer H3
2007 ACCESSORIES & EQUIPMENT Lighting - H3
Schematic Reference: Exterior Lights Schematics
Connector End View Reference: Lighting Systems Connector End Views or Data
Communication Connector End Views
1
Did you perform the Diagnostic System
Check - Vehicle?
Go to Step 2
Go to
Diagnostic
System Check -
Vehicle
2
Verify that the turn signal lamps and/or
indicators are inoperative.
Do the turn signal lamps and/or indicators
operate normally?
Go to Testing
for Intermittent
Conditions and
Poor
Connections
Go to Step 3
3
Are only the turn signal indicators in the
instrument panel cluster (IPC) inoperative?
Go to Step 4
Go to Step 5
4
Test the inoperative turn signal supply
voltage circuit to the IPC for an open or
high resistance. Refer to Circuit Testing
and Wiring Repairs .
Did you find and correct the condition?
Go to Step 13
Go to Step 7
5
1. Place the ignition switch to the ON
position with the engine OFF.
2. Using a scan tool, command the left
and right turn signals ON and OFF
with the BCM special functions scan
tool output controls.
Can you activate the turn signals with the
scan tool?
Go to Step 6
Go to Step 9
6
Test for one of the following conditions.
Refer to Circuit Testing and Wiring
Repairs .
An open, high resistance, short to
ground or short to voltage in the turn
signal switch signal circuit
An open or high resistance in the turn
signal/multifunction switch ground
circuit
2007 Hummer H3
2007 ACCESSORIES & EQUIPMENT Lighting - H3
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст