Hummer H3. Manual — part 934
Cruise Set/Coast Switch
Do all of the parameters listed above
display Off?
Go to Step 3 Go to Step 13
3
1. With the scan tool, observe the
Cruise On/Off Switch
parameter.
2. Turn the cruise On/Off switch
ON.
Does the Cruise On/Off Switch
parameter display On?
-
Go to Step 4 Go to Step 11
4
1. With the scan tool, observe the
Cruise Set/Coast Switch
parameter.
2. Press and hold the set/coast
switch.
Does the Cruise Set/Coast Switch
parameter display On?
-
Go to Step 5 Go to Step 12
5
1. With the scan tool, observe the
Cruise Resume/Accel Switch
parameter.
2. Press and hold the resume/accel
switch.
Does the Cruise Resume/Accel
Switch parameter display On?
-
Go to Step 6 Go to Step 12
6
Do the stop lamps operate properly?
-
Go to Step 7
Go to Stop
Lamps
Inoperative
or
Go to Stop
Lamps
Always On
Test the stop lamp supply voltage
circuit for an open or for a high
resistance. Refer to Circuit Testing
2007 Hummer H3
2007 ACCESSORIES & EQUIPMENT Cruise Control - H3
7
and to Wiring Repairs .
Did you find and correct the
condition?
-
Go to Step
25
Go to Step 8
8
Is the vehicle equipped with a
manual transmission?
-
Go to Step 9
Go to Step 20
9
1. Turn OFF the ignition.
2. Disconnect the clutch release
switch.
3. With a DMM, measure the
resistance of the clutch pedal
position (CPP) switch between
the ignition 1 voltage circuit
and the CPP switch signal
circuit.
Does the resistance measure between
the specified values?
10-15 ohms
Go to Step
10
Go to Step 18
10
1. Depress and hold down the
clutch pedal.
2. With a DMM, measure the
resistance of the CPP switch
between the ignition 1 voltage
circuit and the CPP switch
signal circuit.
Does the resistance measure at the
specified value?
O.L.
Go to Step
14
Go to Step 18
11
Connect a DMM between the
ignition 1 voltage circuit at the back
of C204 and a good ground.
Does the voltage measure at the
specified value?
B+
Go to Step
12
Go to Step 21
1. Turn OFF the ignition.
IMPORTANT:
The cruise control On/Off switch must
be turned ON in order to correctly view
the set/coast resistance value with the
DMM.
2007 Hummer H3
2007 ACCESSORIES & EQUIPMENT Cruise Control - H3
12
2. Disconnect C204.
3. With a DMM, measure the
resistance of the cruise control
switch between the ignition 1
voltage circuit and the cruise
control set/coast and
resume/accelerate switch signal
circuit.
4. Individually activate and hold
the cruise control function
switches while measuring the
resistance of the cruise control
function switches.
Do the cruise control function switch
resistance values measure between
the specified values?
Off = O.L.
On = 7.8 K
ohms - 8.6
K ohms
Resume =
2.7 K ohms
- 3.0 K
ohms
Set = 1.2 K
ohms - 1.3
K ohms
Go to Step
17
Go to Step 19
13
1. Turn OFF the ignition.
2. Disconnect C204.
3. With a DMM, measure the
resistance of the cruise control
switch between the ignition 1
voltage circuit and the cruise
control set/coast and
resume/accelerate switch signal
circuit.
4. Individually activate and hold
the cruise control function
switches while measuring the
resistance of the cruise control
function switches.
Do the resistance values measure at
IMPORTANT:
The cruise control On/Off switch must
be turned ON in order to correctly view
the set coast resistance value with the
DMM.
Off = O.L.
On = 7.8 K
ohms - 8.6
K ohms
Resume =
2.7 K ohms
- 3.0 K
ohms
Set = 1.2 K
ohms - 1.3
K ohms
Go to Step
2007 Hummer H3
2007 ACCESSORIES & EQUIPMENT Cruise Control - H3
the specified values?
16
Go to Step 19
14
1. Turn ON the ignition, with the
engine OFF.
2. Connect a test lamp between
the ignition 1 voltage circuit
and a good ground.
Does the test lamp illuminate?
-
Go to Step
15
Go to Step 21
15
Test the clutch switch signal circuit
for the following:
An open
A short to voltage
A short to ground
A high resistance
Refer to Circuit Testing and
Wiring Repairs .
Did you find and correct the
condition?
-
Go to Step
25
Go to Step 20
16
Test the cruise control set/coast and
resume/accelerate switch signal
circuit for a short to voltage. Refer to
Circuit Testing and Wiring
Repairs .
Did you find and correct the
condition?
-
Go to Step
25
Go to Step 20
17
Test the cruise control set/coast and
resume/accelerate switch signal
circuit for the following:
An open
A high resistance
A short to ground
Refer to Circuit Testing and
-
2007 Hummer H3
2007 ACCESSORIES & EQUIPMENT Cruise Control - H3
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст