Hummer H1 (2006+). Manual — part 298
10-54 Body
______________________________________________________________________
16. Remove the retainer and the harness from the door assembly.
Figure 10-58: Heated Power Mirrors Door Harness
Figure 10-59: Power Windows and Door Locks Connections
Installation
NOTE: Lubricate the bushing, grommet and harness teflon cover with silicone spray.
1.
Route the harness through the harness mounting bracket, mounting bracket bushing and the door bushing (Figure 10-60).
2.
Install the harness mounting bracket on the door assembly with the two self-tapping screws (Figure 10-61).
3.
Route the harness through the A-pillar rubber grommet (Figure 10-59).
POWER MIRRORS
DOOR JUMPER
CONNECTORS
HARNESS
CONNECTORS
HARNESS
HEATED
POWER
MIRROR
CONNECTOR
FRONT DOOR
POWER WINDOWS
AND DOOR LOCKS
BODY HARNESS
6-WAY
4-WAY
A-PILLAR
TEFLON
CONNECTOR
CONNECTOR
HARNESS
HEATED POWER
GROMMET
MIRRORS HARNESS
TUBE
_____________________________________________________________________
Body 10-55
Figure 10-60: Heated Power Mirrors Door Harness
NOTE: When connecting the harness wires to the 4-way and 6-way connectors, ensure the wire colors align with the mating con-
nector wires.
4.
Connect the harness wires to the 4-way and the 6-way connectors.
5.
Connect the 4-way and the 6-way harness connectors to the power windows and the door locks body harness connectors.
6.
Connect the two harness connectors to the power mirrors body harness connectors.
7.
Secure the harness to the A-pillar with the clamp, self-tapping screw, nut and the lock washer assembly.
NOTE: Be careful to match the wire colors, since the harness connectors can be interchanged.
8.
Connect the two harness connectors to the power mirrors door jumper harness connectors (Figure 10-59).
9.
Connect the harness connector to the power window regulator (Figure 10-61).
10. Connect the harness connector to the power door lock actuator.
11. Secure the harness to the door reinforcement with the clamp and the self-tapping screw.
12. Secure the harness to the door assembly with the retainer.
13. Install the moisture barrier flap, vapor barrier and the door trim panel on the door (Refer to section 10).
14. Install the front outer kick panels (Refer to section 10).
15. Connect the battery ground cable (Refer to section 12).
16. Check the power windows and the door locks for proper operation.
POWER MIRRORS
DOOR JUMPER
CONNECTORS
HARNESS
CONNECTORS
HARNESS
HEATED
POWER
MIRROR
CONNECTOR
10-56 Body
______________________________________________________________________
Figure 10-61: Power Windows and Door Locks Door Harness
POWER WINDOWS AND DOOR LOCKS REAR DOOR HARNESS REPLACEMENT
Removal
1.
Remove the center outer kick panel and the lower B-pillar trim (Refer to section 10).
2.
Remove the rear door trim, vapor barrier and the moisture barrier flap from the door (Refer to section 10).
NOTE: Tag the leads for installation.
3.
Disconnect the 6-way harness connector from the power windows and the door locks rear door jumper harness connector
(Figure 10-62).
POWER DOOR LOCKS
POWER WINDOW
REGULATOR BRACKET
FRONT
MOUNTING
BRACKET
BUSHING
DOOR
HARNESS
ACTUATOR
REGULATOR
MOUNTING
BRACKET
_____________________________________________________________________
Body 10-57
Figure 10-62: Rear Door Harness and Rear Door Jumper Harness
4.
Remove the harness wires from the 6-way connector.
5.
Remove the screw, nut, lock washer and the clamp securing the harness to the B-pillar. Discard the nut and the lock washer
assembly.
NOTE: Lubricate the bushings, grommet and the harness teflon cover with silicone spray.
6.
Pull the harness through the B-pillar rubber grommet.
7.
Remove and inspect the B-pillar rubber grommet. Replace it if damaged.
8.
Remove the two self-tapping screws and the harness mounting bracket from the door assembly (Figure 10-63).
9.
Pull the harness through the door bushing.
10. Inspect the door bushing and replace it if damaged.
11. Remove the harness mounting bracket and the mounting bracket bushing from the harness. Inspect the bushing and replace it
if damaged.
12. Remove the self-tapping screw and the clamp securing the harness to the door reinforcement.
13. Disconnect the harness connector from the power window regulator (push the locking tab up on the bottom of the connector).
14. Disconnect the harness connector from the power door lock actuator.
15. Remove the retainer securing the harness to the door assembly.
16. Remove the tie strap and the harness from the door assembly. Discard the tie strap.
TEFLON TUBE
GROMMET
REAR DOOR
6-WAY CONNECTOR
REAR DOOR JUMPER HARNESS
B-PILLAR
HARNESS
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст