Hummer H1 (2006+). Manual — part 294
10-38 Body
______________________________________________________________________
5.
Remove the screws and the lower C-pillar trim from the C-pillar.
6.
Remove the dome light.
7.
Remove the panel fasteners and the rear headliner from the J-channel.
Installation
1.
Secure the rear headliner to the J-channel and the roof with the panel fasteners.
2.
Install the dome light.
3.
Secure the trim panel to the compartment wall with the screw.
4.
Secure the lower C-pillar trim to the lower side of the C-pillar with the screws.
5.
Secure the seat belt assembly and bracket to the C-pillar with the washers and bolts. Tighten the bolts to 35-40 lb-ft (47-55
N•m).
6.
Secure the upper C-pillar trim to the C-pillar with the screws.
7.
Install the rear seats.
Inner Kick Panels Replacement
Removal
1.
Remove the seats.
2.
Remove bolts, washers and seat buckles from front and rear of tunnel (Figure 10-40).
Figure 10-40: Seat Belt Buckle Electrical Connector Location
NOTE: Ensure the seat belt buckle electrical connector or wiring harness is pulled out and away from the kick panel for ease of in-
stallation.
3.
Disconnect the seat belt buckle electrical connector from the wiring harness connector on the driver side.
4.
Remove the panel fasteners, screw/washer assemblies and the rear wall trim from the rear compartment wall (Figure 10-41).
5.
Remove the panel fasteners and the rear inner kick panel from the tunnel (Figure 10-42).
WIRING
HARNESS
CONNECTOR
SEAT BELT BUCKLE
ELECTRICAL
CONNECTOR
SEAT
BELT
BUCKLE
_____________________________________________________________________
Body 10-39
Figure 10-41: Rear Compartment Trim Removal
Figure 10-42: Inner Kick Panel Mounting
6.
Remove the center consoles.
7.
Remove the screws, panel fastener and the shift control panel from the tunnel (Figure 10-42).
8.
Remove the panel fasteners and the left front inner kick panel from the tunnel.
9.
Remove the panel fasteners and the right front inner kick panel.
10. Remove the panel fastener and the inner kick panel from the rear of tunnel.
Installation
1.
Secure the rear inner kick panel to the right rear of the tunnel with the panel fastener (Figure 10-42).
2.
Secure the right front inner kick panel to the tunnel with the panel fasteners.
3.
Secure the left front inner kick panel to the tunnel with the panel fasteners.
4.
Secure the shift control trim panel to the tunnel with the screw/washer assemblies and the panel fastener.
5.
Install the center consoles.
REAR
REAR
PANEL
FASTENER
WALL TRIM
COMPARTMENT
COMPARTMENT
WALL
PANEL
RIGHT FRONT
TUNNEL
LEFT FRONT
REAR INNER
KICK PANELS
INNER KICK
PANEL
INNER KICK PANEL
SHIFT
CONTROL
TRIM PANEL
KICK
PANEL
10-40 Body
______________________________________________________________________
6.
Secure the rear inner kick panels with the panel fasteners (Figure 10-41).
7.
Secure the rear wall trim to the rear compartment wall with the panel fasteners and the screw/washer assemblies.
8.
Connect the driver side seat belt buckle electrical connector (Figure 10-40).
9.
Secure the seat buckles to the tunnel with the washers and the bolts. Tighten the bolts to 35-40 lb-ft (47-55 N•m).
10. Install the seats.
Outer Kick Panel Replacement
Removal
1.
Remove the door stop straps.
2.
Remove the panel fasteners and the right front outer kick panel from the body (Figure 10-43).
3.
Remove the panel fasteners and the left front outer kick panel from the body.
4.
Remove the panel fasteners and the left center outer kick panel from the body.
5.
Remove the panel fastener and the right center outer kick panel from the body.
6.
Remove the screws, washers and the rear lower seat belt brackets from the body.
7.
Remove the panel fasteners and the left and right rear outer kick panels from the body.
Figure 10-43: Outer Kick Panel Identification
Installation
1.
Secure the left and the right rear outer kick panels to the body with the panel fasteners (Figure 10-43).
2.
Secure the rear lower seat belt brackets to the body with the washers and the screws.
3.
Secure the right center outer kick panel to the body with the panel fastener.
4.
Secure the left center outer kick panel to the body with the panel fasteners.
5.
Secure the left front outer kick panel to the body with the panel fasteners.
6.
Secure the right front outer kick panel to the body with the panel fasteners.
7.
Install the door stop straps.
Tunnel Carpet, Padding and Hardboard Replacement
Removal
1.
Remove the inner kick panels.
2.
Remove the carpet from the tunnel (Figure 10-44).
3.
Remove the padding from the tunnel.
PANEL FASTENER
SEAT BELT
BODY
REAR KICK
CENTER KICK
FRONT KICK
BRACKET
PANELS
PANEL
PANELS
CENTER KICK
PANEL
LOWER
_____________________________________________________________________
Body 10-41
4.
Remove the panel fasteners and the hardboard from the tunnel.
Installation
1.
Secure the hardboard to the tunnel with the panel fasteners (Figure 10-44).
2.
Install the padding on the tunnel.
3.
Install the carpet on the tunnel.
4.
Install the inner kick panels.
Figure 10-44: Carpet and Padding Installation
VISOR REPLACEMENT
Removal
NOTE: The visor replacement is the same for each side of the vehicle. This procedure covers the driver’s side.
1.
Remove the six screws, lock washers and the visor from the body (Figure 10-45).
Installation
1.
Secure the visor mounting brackets to the body with the six screws, lock washers and washers.
CARPET
PADDING
HARDBOARD
PANEL FASTENER
TUNNEL
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст