Hummer H1 (2006+). Manual — part 242
7-50
Brake System
_____________________________________________________________
4-0
Short circuit to
ground between
ECU and right
front inlet solenoid
valve.
6 and 27
5.0-7.5
Ω
Check electrical resistance of affected valve wir-
ing to ground at ECU connector and at modulator
assembly as necessary.
4-1
Short circuit to
ground between
ECU and right
front outlet sole-
noid valve.
7 and 27
3.0-5.0
Ω
Check electrical resistance of affected valve wir-
ing to ground at ECU connector and at modulator
assembly as necessary.
4-2
Short circuit to
ground between
ECU and left front
inlet solenoid valve.
23 and 27
5.0-7.5
Ω
Check electrical resistance of affected valve wir-
ing to ground at ECU connector and at modulator
assembly as necessary.
4-3
Short circuit to
ground between
ECU and left front
outlet solenoid
valve.
24 and 27
3.0-5.0
Ω
Check electrical resistance of affected valve wir-
ing to ground at ECU connector and at modulator
assembly as necessary.
4-4
Short circuit to
ground between
ECU and right rear
inlet solenoid valve.
4 and 27
5.0-7.5
Ω
Check electrical resistance of affected valve wir-
ing to ground at ECU connector and at modulator
assembly as necessary.
4-5
Short circuit to
ground between
ECU and right rear
outlet solenoid
valve.
5 and 27
3.0-5.0
Ω
Check electrical resistance of affected valve wir-
ing to ground at ECU connector and at modulator
assembly as necessary.
4-6
Short circuit to
ground between
ECU and left rear
inlet solenoid valve.
21 and 27
5.0-7.5
Ω
Check electrical resistance of affected valve wir-
ing to ground at ECU connector and at modulator
assembly as necessary.
4-7
Short circuit to
ground between
ECU and left rear
outlet solenoid
valve.
22 and 27
3.0-5.0
Ω
Check electrical resistance of affected valve wir-
ing to ground at ECU connector and at modulator
assembly as necessary.
4-8
Short circuit to
ground between
ECU and RCP relay
1.
Remove Relay
1
11 or 30 and 27
Open circuit
Check wiring to pump relay and pump connector
through pump. Repair wiring or replace modula-
tor as necessary.
Fault Code List - Ignition key “OFF” to test system (except where noted)
Test pin locations refer to ABS Pinout Box J–35592
Fault Code
Problem Area
Test Pin
Locations
Values
Check/Repair
6-1-05
____________________________________________________________
Brake System 7-51
5745804
4-9
Short circuit to
ground between
ECU and RCP relay
2.
Remove Relay
2
12 and 27
Open circuit
Check wiring to pump relay and pump connector
through pump. Repair wiring or replace modula-
tor as necessary.
4-12
Right front wheel
speed sensor open
circuit.
17 and 34
500-2000
Ω
Check electrical resistance of affected sensor and
wiring at ECU connector and at harness plugs.
Repair wiring or replace sensor as necessary.
4-13
Left rear wheel
speed sensor open
circuit.
18 and 35
500-2000
Ω
Check electrical resistance of affected sensor and
wiring at ECU connector and at harness plugs.
Repair wiring or replace sensor as necessary.
4-14
Left front wheel
speed sensor open
circuit.
15 and 32
500-2000
Ω
Check electrical resistance of affected sensor and
wiring at ECU connector and at harness plugs.
Repair wiring or replace sensor as necessary.
4-15
Right rear wheel
speed sensor open
circuit.
16 and 33
500-2000
Ω
Check electrical resistance of affected sensor and
wiring at ECU connector and at harness plugs.
Repair wiring or replace sensor as necessary.
5-0
Short circuit to bat-
tery between ECU
and right front inlet
valve solenoid or
wiring.
6 and 27
0 volts
5.0-7.5
Ω
Check voltages at wiring harness including con-
nectors. Check electrical resistance of affected
valve wiring to ground at ECU connector and at
modulator assembly plug. Repair wiring or
replace as necessary.
5-1
Short circuit to bat-
tery between ECU
and right front out-
let valve solenoid or
wiring.
7 and 27
0 volts
3.0-5.0
Ω
Check voltages at wiring harness including con-
nectors. Check electrical resistance of affected
valve wiring to ground at ECU connector and at
modulator assembly plug. Repair wiring or
replace as necessary.
5-2
Short circuit to bat-
tery between ECU
and left front inlet
valve solenoid or
wiring.
23 and 27
0 volts
5.0-7.5
Ω
Check voltages at wiring harness including con-
nectors. Check electrical resistance of affected
valve wiring to ground at ECU connector and at
modulator assembly plug. Repair wiring or
replace as necessary.
5-3
Short circuit to bat-
tery between ECU
and left front outlet
valve solenoid or
wiring.
24 and 27
0 volts
3.0-5.0
Ω
Check voltages at wiring harness including con-
nectors. Check electrical resistance of affected
valve wiring to ground at ECU connector and at
modulator assembly plug. Repair wiring or
replace as necessary.
5-4
Short circuit to bat-
tery between ECU
and right rear inlet
valve solenoid or
wiring.
4 and 27
0 volts
5.0-7.5
Ω
Check voltages at wiring harness including con-
nectors. Check electrical resistance of affected
valve wiring to ground at ECU connector and at
modulator assembly plug. Repair wiring or
replace as necessary.
Fault Code List - Ignition key “OFF” to test system (except where noted)
Test pin locations refer to ABS Pinout Box J–35592
Fault Code
Problem Area
Test Pin
Locations
Values
Check/Repair
6-1-05
7-52
Brake System
_____________________________________________________________
5-5
Short circuit to bat-
tery between ECU
and right rear out-
let valve solenoid or
wiring.
5 and 27
0 volts
3.0-5.0
Ω
Check voltages at wiring harness including con-
nectors. Check electrical resistance of affected
valve wiring to ground at ECU connector and at
modulator assembly plug. Repair wiring or
replace as necessary.
5-6
Short circuit to bat-
tery between ECU
and left rear inlet
valve solenoid or
wiring.
21 and 27
0 volts
5.0-7.5
Ω
Check voltages at wiring harness including con-
nectors. Check electrical resistance of affected
valve wiring to ground at ECU connector and at
modulator assembly plug. Repair wiring or
replace as necessary.
5-7
Short circuit to bat-
tery between ECU
and left rear outlet
valve solenoid or
wiring.
22 and 27
0 volts
3.0-5.0
Ω
Check voltages at wiring harness including con-
nectors. Check electrical resistance of affected
valve wiring to ground at ECU connector and at
modulator assembly plug. Repair wiring or
replace as necessary.
5-8
Short circuit to bat-
tery + between ECU
and RCP relay 1.
11 and 27
0 volts
Check wiring harness between ECU and relay and
pump ground connections. Repair wiring as nec-
essary.
5-9
Short circuit to bat-
tery + between ECU
and RCP relay 2.
12 and 27
0 volts
Check wiring harness between ECU and relay and
pump ground connections. Repair wiring as nec-
essary.
5-12
Right front wheel
speed signal is
erratic.
17 and 34
Greater than
0.9 volts AC
at one tire rev-
olution per
second.
Check for damaged tone wheel, incorrect sensor
adjustment, excessive tone wheel runnout (> .041"),
excessive geared hub input bearing play and tire size
mismatch. Repair or replace as necessary.
5-13
Left rear wheel
speed signal is
erratic.
18 and 35
Greater than
0.9 volts AC
at one tire rev-
olution per
second.
Check for damaged tone wheel, incorrect sensor
adjustment, excessive tone wheel runnout (> .041"),
excessive geared hub input bearing play and tire size
mismatch. Repair or replace as necessary.
5-14
Left front wheel
speed signal is
erratic.
15 and 32
Greater than
0.9 volts AC
at one tire rev-
olution per
second.
Check for damaged tone wheel, incorrect sensor
adjustment, excessive tone wheel runnout (> .041"),
excessive geared hub input bearing play and tire size
mismatch. Repair or replace as necessary.
5-15
Right rear wheel
speed signal is
erratic.
16 and 33
Greater than
0.9 volts AC
at one tire rev-
olution per
second
Check for damaged tone wheel, incorrect sensor
adjustment, excessive tone wheel runnout (> .041"),
excessive geared hub input bearing play and tire size
mismatch. Repair or replace as necessary.
Fault Code List - Ignition key “OFF” to test system (except where noted)
Test pin locations refer to ABS Pinout Box J–35592
Fault Code
Problem Area
Test Pin
Locations
Values
Check/Repair
6-1-05
____________________________________________________________
Brake System 7-53
5745804
6-0
Short circuit
between two sole-
noid valve leads of
right front inlet
solenoid valve.
6 and 4, 5, 7,
21, 22, 23, 24
6.0-15.0
Ω
Check electrical resistance of affected valves and
wiring at ECU connector and at modulator assem-
bly plug. Repair or replace wiring as necessary
and replace modulator if short is internal.
Note: Fault code for both affected valves will be
stored in memory.
6-1
Short circuit
between two sole-
noid valve leads of
right front outlet
solenoid valve.
7 and 4, 5, 6,
21, 22, 23, 24
6.0-15.0
Ω
Check electrical resistance of affected valves and
wiring at ECU connector and at modulator assem-
bly plug. Repair or replace wiring as necessary
and replace modulator if short is internal.
Note: Fault code for both affected valves will be
stored in memory.
6-2
Short circuit
between two sole-
noid valve leads of
left front inlet sole-
noid valve.
23 and 4, 5, 6,
7, 21, 22, 24
6.0-15.0
Ω
Check electrical resistance of affected valves and
wiring at ECU connector and at modulator assem-
bly plug. Repair or replace wiring as necessary
and replace modulator if short is internal.
Note: Fault code for both affected valves will be
stored in memory.
6-3
Short circuit
between two sole-
noid valve leads of
right front outlet
solenoid valve.
24 and 4, 5, 6,
7, 21, 22, 23
6.0-15.0
Ω
Check electrical resistance of affected valves and
wiring at ECU connector and at modulator assem-
bly plug. Repair or replace wiring as necessary
and replace modulator if short is internal.
Note: Fault code for both affected valves will be
stored in memory.
6-4
Short circuit
between two sole-
noid valve leads of
right rear inlet
solenoid valve.
4 and 5, 6, 7,
21, 22, 23, 24
6.0-15.0
Ω
Check electrical resistance of affected valves and
wiring at ECU connector and at modulator assem-
bly plug. Repair or replace wiring as necessary
and replace modulator if short is internal.
Note: Fault code for both affected valves will be
stored in memory.
6-5
Short circuit
between two sole-
noid valve leads of
right rear outlet
solenoid valve.
5 and 4, 6, 7,
21, 22, 23, 24
6.0-15.0
Ω
Check electrical resistance of affected valves and
wiring at ECU connector and at modulator assem-
bly plug. Repair or replace wiring as necessary
and replace modulator if short is internal.
Note: Fault code for both affected valves will be
stored in memory.
6-6
Short circuit
between two sole-
noid valve leads of
left rear inlet sole-
noid valve.
21 and 4, 5, 6,
7, 22, 23, 24
6.0-15.0
Ω
Check electrical resistance of affected valves and
wiring at ECU connector and at modulator assem-
bly plug. Repair or replace wiring as necessary
and replace modulator if short is internal.
Note: Fault code for both affected valves will be
stored in memory.
Fault Code List - Ignition key “OFF” to test system (except where noted)
Test pin locations refer to ABS Pinout Box J–35592
Fault Code
Problem Area
Test Pin
Locations
Values
Check/Repair
6-1-05
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст