Hummer H1 (2006+). Manual — part 309
10-98 Body
______________________________________________________________________
Figure 10-117: Rear Wall Compartment Location
Installation
1.
Secure the center trim to the rear compartment wall with the screw and the washer assembly (Figure 10-117).
2.
Secure the lower trim and the trim to the rear compartment wall with the two panel fasteners and the four screw and the washer
assemblies.
3.
Secure the trim to the rear compartment wall with the four screw and the washer assemblies.
4.
Connect the courtesy light electrical connector, and secure the courtesy light to the trim with the two washers and the rivets
(Figure 10-117).
5.
Secure the courtesy light lens to the courtesy light bracket.
6.
Fasten the lower B-pillar trim with the three screws.
7.
Secure the windshield center trim to the windshield frame with the two screw.
8.
Install the speakers on the rear wall (Section 12).
9.
Install the center console.
10. Install the front and the rear seats.
Soft Top Mounting Components Replacement
NOTE: The following removal and installation instructions include replacement of all soft top mounting components and accesso-
ries. Use only the applicable steps for replacing specific components.
Removal
1.
Remove the four-passenger soft top, tonneau cover or station wagon soft top, if applicable. Refer to the owner’s manual for
proper procedure.
2.
Remove the tonneau cover wood bow from the two retainer brackets (Figure 10-118).
3.
Remove the four screws and the two bow retainer brackets from the wheelhouses.
CENTER TRIM
PANEL
TRIM
FASTENER
LOWER
LOWER
B-PILLAR
TRIM
_____________________________________________________________________
Body 10-99
Figure 10-118: Tonneau Cover Wood Bow Removal
4.
Remove the velcro strips and the patches from the tonneau area (Figure 10-119).
NOTE: Perform steps five and six for both sides of the vehicle. The left side is shown.
5.
Remove the 41 in. (104 cm) tonneau extrusion from the side of the wheelhouse.
6.
Remove the 9 in. (23 cm) tonneau extrusion from the rear of the wheelhouse.
7.
Remove the 43 in. (109 cm) tonneau extrusion from the tailgate.
Figure 10-119: Velcro Strip and Patch Removal
8.
Remove the five screws, lockwashers, four self-tapping screws and the tonneau/rear curtain extrusion from the body.
TONNEAU COVER
WHEELHOUSE
BOW RETAINER
WOOD BOW
BRACKET
TONNEAU/REAR CURTAIN EXTRUSION
VELCRO STRIP
TAILGATE CHAIN
VELCRO PATCH
43 IN. (109 cm)
TONNEAU EXTRUSION
43 IN. (109 CM)
9 IN. (23 CM)
9 IN. (23 CM)
41 IN. (104 CM)
41 IN. (104 CM)
VELCRO PATCH
ATTACHMENT CHANNEL
VELCRO STRIP
2 IN. (5 CM)
FROM EDGE
VELCRO STRIP
VELCRO STRIP
TONNEAU EXTRUSION
TONNEAU EXTRUSION
WHEEL HOUSE
10-100 Body
____________________________________________________________________
9.
Remove the front and the rear inner door seals (Figure 10-120).
Figure 10-120: Door Seal Removal
NOTE: This procedure is written for the left side of the vehicle only. Duplicate steps are necessary to service the right hand side.
10. Remove the soft top from the vehicle.
11. Remove the D-strip seal from the windshield frame. Do not remove the P-strip seal (Figure 10-121).
Figure 10-121: D-Strip Seal Removal
12. Remove the 12 screws securing the front attachment rail to the top of the windshield frame and remove the rail.
13. Slide the velcro strips in the two side rails, rearward to remove and set aside.
14. Remove the four screws securing the B-pillar cover to the bottom of the H-rail.
INNER DOOR SEAL
8-S10-002
P-STRIP SEAL
D-STRIP SEAL
___________________________________________________________________
Body 10-101
Figure 10-122: B-Pillar Cover Removal
15. Remove the two bolts securing the B-pillar cover to the B-pillar. Remove the B-pillar cover (Figure 10-122).
16. Remove the three screws securing the C-pillar cover to the H-rail (Figure 10-123).
17. Remove the four bolts securing the lower inner and outer bracket on the C-pillar cover. Remove the cover.
Figure 10-123: C-Pillar Cover Removal
18. Remove the three screws securing the H-Rail to the vehicle safety cage. Leave the L-brackets on the safety cage unless the
cage is going to be replaced, remove the H-rail (Figure 10-124).
UPPER
LOWER
H-RAIL
FILLER PIECE
B-PILLAR
COVER
RETAINING
SCREWS
RETAINING
SCREWS
8-S10-003
C-PILLAR
UPPER
LOWER
RETAINING
SCREWS
COVER
RETAINING
SCREWS
8-S10-004
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст