Hummer H1 (2006+). Manual — part 22
1-40
General Information, Lubrication and Maintenance
________________
Master Cylinder Fluid Level Check
CAUTION: Use DOT 3 brake fluid only. Failure to use the proper fluid may affect brake performance or damage brake compo-
nents.
Check master cylinder fluid level monthly. Correct fluid level is to within 1/2 in. (13 mm) from the “MAX” indicator.
Clean the master cylinder cap and exterior before checking fluid level. Dirt on the cap must not be allowed to enter the reservoirs.
Add DOT 3 fluid if necessary and reinstall the cap (Figure-1-37).
Figure 1-37: Master Cylinder Cap Location
Wheels/Tires/CTIS
Inspect tire and wheel condition. Look for loose wheel nuts and rim stud nuts, or dented, deformed wheel rims. Note tire tread wear
and sidewall condition. If the vehicle is used for extensive off road operation, check the sidewalls for bulges, bead damage, cuts,
fabric breaks.
If the tire treads are worn, note type of wear. If wear is only on one shoulder, toe setting or camber may be incorrect. If tires are
scalloped or worn at crown only, or both shoulders, inflation pressures are probably incorrect.
If the vehicle is equipped with CTIS, cycle the system and check operation. Verify tire inflation pressures with an accurate gauge.
Serpentine Belt
Replace the belt if frayed, cut, or torn. Minor, small surface cracks within the belt grooves are normal. Do not replace the belt un-
less cracks extend all the way through or across the belt face.
Body Lubrication Points
Every 6 months or 6,000 mi (9,700 km), whichever occurs first, lubricate the: hood hinge, hood stops, tailgate hinges, door hinges,
door handles, parking brake lever and service brake pedal push rod stud (Figure-1-38). Suggested lubricants include engine oil or
ATF for hinges; LPS silicone lube for linkages, handles, and brake push rod; white grease for seat tracks, window regulators and
park brake lever. Door locks should use a graphite based lubricant such as Lock-Eze. Refer to the Recommended Fuel/Fluids/Lu-
bricants/Capacities section for more detailed lube information.
MASTER CYLINDER
CAP
MAX FLUID
LEVEL
INDICATOR
12-1-05
_______________
General Information, Lubrication and Maintenance 1-41
5745804
Figure 1-38: Body Lubrication Points
ESSENTIAL TOOLS
NOTE: See page 1-1 of the 2006 Service Parts Catalog for information on ordering Kent-Moore tools.
Engine
Tool No.
Description
EN-47913
Wrench, Belt Tensioner
J–23523-F
Harmonic Balancer Remover/Installer Set
J–23951
Water Manometer
J–26999-10
Compression Gauge Adapter
J–26999-20
Adapter, Compression Gauge
J–26999-30
Compression Gauge Adapter
J–34826
Socket, 36mm 12 Point
J–42000-EU
Digital Battery Tester
J–44640
Installer, Valve Stem Seal
J–44641
Remover, Rear Crankshaft Seal
J–44642
Installer, Rear Crankshaft Seal
J–44643
Flywheel Holder
J–44644
Remover, Front Crankshaft Seal
J–44645
Installer, Front Crankshaft Seal
J–44646
Compressor, Valve Spring (On-Vehicle)
J–44648-A
Storage Case - Duramax 6.6L Tools
J-45059
Angle Meter
J–46594
Tool, Injector Removal
DOOR
TRANSFER CASE
DOOR
DOOR
TAILGATE
DOOR
TRANSMISSION
SEAT
PARKING BRAKE
SERVICE BRAKE PEDAL
HOOD
SHIFT LINKAGE
SHIFT LINKAGE
PUSH ROD STUD
LEVER
HINGE
HINGE
HANDLE
TRACKS
HINGE
LOCKS
HINGE
CENTER
HOOD
STOP
HOOD
STOP
(GREASE)
HOOD
STOP
(GREASE)
(GREASE)
11-1-05
1-42
General Information, Lubrication and Maintenance
________________
Fuel, Emissions and Exhaust
Transmission/Transfer Case
Tool No.
Description
EN–47589
Test Adapter, Fuel Pressure
J–28552-A
Gauge, Fuel Pressure
J–28552-100
Fuel Pressure/Return Adapter Set
J–29658-D
Fuel Pressure Gauge & Adapter Set
J–29698-A
Injection Line (flare nut) Wrench, 3/4
J–38641-B
Hydrometer, Diesel Fuel
J–44638
Gauge, Vacuum/Pressure
J–45773
Adapters, Fuel Pressure Gauge
J–45873
Test Kit, Fuel Return Volume
J–45873-30
Test Adapters, Fuel Return Volumn
Tool No.
Description
DT–47502
Front Output Seal Installer
J–21366
Torque Converter Retaining Strap
J–25025-B
Oil Pump and Valve Body Pin Set
J–33831-A
Input Gear Seal Installer
J–33835
Pump Housing Seal Installer
J–39700
Break-Out Box
J–41364-A
NSBU Switch Aligner
J–41623-B
Trans Oil Cooler Line Disconnect Tool
J–42497
Extension Housing Seal Installer
J–42543
Selector Shaft Seal Remover/Installer
J–43773
Valve Spring Compressor
J–43799
Break-Out Box Adapter
J–43909
Selector Shaft Seal Installer
J–43911
Selector Shaft Seal Remover
J–44152
Jumper Harness (20 pins)
J–44247
Internal Wiring Harness Installer
J–44257
Wiring Harness Connector Remover
J–44835
Allison Transmission Oil Cooler Flush Adapters
J–44924-A
Storage Case - Allison LCT Tools
J–45053
Pump Remover
J–45056
Oil Pressure Adapter
J–45096
TransFlow Transmission Cooling System Service Tool
J–45096-500
Oil Flush Kit Adapters
J–46409
Torque Converter Alignment Handles
11-1-05
_______________
General Information, Lubrication and Maintenance 1-43
5745804
Wheels, Tires and CTIS
Brakes
Steering
Axles/Suspension and Frame
Tool No.
Description
CH–47503
Runflat Tire Pry Bar
J–39522
ENG Kit, Socket (5-Point)
J–42452
Runflat Compressor
J–42557
Socket, Cam
J–45760
Rim Separating Jack-Screws
J–45769
Runflat Ratchet Wrench
J–45770
Hutchinson Rim Separator
Tool No.
Description
J–35592
ABS Pinout Box
J–42553
Disc Brake Piston Retraction Tool
J–42883
Wheel Speed Sensor Test Cable
J–44237
ABS Blink Code Jumper
J–44238
Master Cylinder Bleed Adapter
J–45405
Brake Line Flaring Kit
J–45761
T-Handle Rachet Wrench (9/16")
Tool No.
Description
J–33141
Adapter Fittings (used with J–25323)
J–42548
Puller, Pitman Arm
J–44721
Power Steering System Analyzer
J–8092
Universal Driver Handle
Tool No.
Description
CH–47505
Shock Mounting Pin Socket
DT–47845
Installer, Input Seal
DT–47846
Installer, Spindle Seal
J–08614-A
Pinion Flange Holder
J–08614-5
Bolt Kit Yoke Holding Tool
J–22610
Axle Boot Pliers, Eared Clamp
J–24398-A
Driveshaft Inclinometer
J–35566
Clamp Tool, Axle Boot
J–35910
Axle Boot Crimping Tool
J–38792-A
Electronic Vibration Analyzer (EVA) 2
J–38869
Installer, Pinion Seal
J–42183
Handle, Seal Driver
J–42546
1/4 in. Drive Torque Wrench (Preset)
J–42547
1/2 in. Drive Torque Wrench (Preset)
J–43218
Clamp Plier
J–45762
T-Handle Rachet Wrench (15mm)
J–8092
Universal Driver Handle
11-1-05
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст