Hummer H1 (2006+). Manual — part 5
1-18
General Information, Lubrication and Maintenance
________________
Bolt Head ID Marks and SAE Grade
BOLT
SIZE
SAE GRADE
NO. 1 OR 2
SAE GRADE
NO. 5
SAE GRADE
NO. 6 OR 7
SAE GRADE
NO. 8
DIA.
INCHES
MILLI-
METERS
THREADS
PER INCH
POUND FEET
(NEWTON-
METERS)
POUND FEET
(NEWTON-
METERS)
POUND FEET
(NEWTON-
METERS)
POUND FEET
(NEWTON-
METERS)
1/4
6
20
4(5)
7(10)
9(12)
11(15)
1/4
6
28
5(7) 9(12)
—— 13(17)
5/16
8
18
10(14)
15(20)
17(23)
22(30)
5/16
8
24
12(16)
17(23)
—— 24(33)
3/8
10
16
16(22)
28(38)
31(42)
40(54)
3/8
10
24
18(24)
32(43)
—— 44(60)
7/16
11
14
25(34)
44(60)
50(68)
63(85)
7/16
11
20
27(37)
50(68)
—— 70(95)
1/2
13
13
35(48)
68(92)
77(104)
95(129)
1/2
13
20
37(50)
77(104)
—— 108(146)
9/16
14
12
46(62)
99(134)
108(146)
140(190)
9/16
14
18
50(67)
108(146)
—— 153(207)
5/8
16
11
57(77)
135(183)
150(203)
189(256)
5/8
16
18
85(115)
153(207)
—— 216(293)
3/4
19
10
95(129)
243(330)
252(342)
338(458)
3/4
19
16
104(141)
266(361)
—— 378(513)
7/8
22
9
144(195)
356(483)
396(537)
545(739)
7/8
22
14
158(214)
392(532)
——
608(824)
1
25
8
212(287)
531(720)
594(805)
819(1111)
1
25
14
225(305) 594(805)
——
891(1208)
1-1/8
29
—
——
720 - 792
(976 - 1074)
——
1152 - 1296
(1562 - 1757)
1-1/4
32
—
——
——
——
1638 - 1800
(2221 - 2441)
1-3/8
35
—
——
1314 - 1512
(1782 - 2050)
—— ——
1-1/2
39
—
——
1746 - 1980
(2368 - 2685)
——
2844 - 3204
(3857 - 4345)
_______________
General Information, Lubrication and Maintenance 1-19
5745804
U.S./METRIC CONVERSIONS AND EQUIVALENTS
Metric Conversions
U.S. Standard Conversions
Temperature
32° FAHRENHEIT = 0° CELSIUS 212° FAHRENHEIT = 100° CELSIUS
CELSIUS = 0.556 X (F° -32) FAHRENHEIT = (1.8 X C°) +32
MULTIPLY
BY
TO GET
INCHES
2.54
CENTIMETERS
FEET
0.3048
METERS
MILES
1.6093
KILOMETERS
SQUARE INCHES
6.451
SQUARE CENTIMETERS
CUBIC INCHES
16.39
CUBIC CENTIMETERS
FLUID OUNCES
29.573
MILLILITERS
PINTS
0.473
LITERS
QUARTS
0.946
LITERS
GALLON
3.785
LITERS
POUNDS
0.454
KILOGRAMS
SHORT TONS
0.907
METRIC TONS
POUND-INCHES
0.113
NEWTON-METERS
POUND-FEET
1.356
NEWTON-METERS
POUNDS PER SQUARE INCH
6.895
KILOPASCALS
MILES PER GALLON
0.425
KILOMETERS PER LITER
MILES PER HOUR
1.609
KILOMETERS PER HOUR
MULTIPLY
BY
TO GET
MILLIMETERS
0.03937
INCHES
CENTIMETERS
0.3937
INCHES
METERS
3.2808
FEET
KILOMETERS
0.6214
MILES
SQUARE CENTIMETERS
0.155
SQUARE INCHES
CUBIC CENTIMETERS
0.061
CUBIC INCHES
MILLILITERS
0.034
FLUID OUNCES
LITERS
2.113
PINTS
LITERS
1.057
QUARTS
LITERS
0.264
GALLONS
KILOGRAMS
2.205
POUNDS
METRIC TONS
1.102
SHORT TONS
NEWTON-METERS
0.738
POUND-FEET
NEWTON-METERS
8.851
POUND-INCHES
KILOPASCALS
0.145
POUNDS PER SQUARE INCH
KILOMETERS PER LITER
2.352
MILES PER GALLON
KILOMETERS PER HOUR
0.621
MILES PER HOUR
1-20
General Information, Lubrication and Maintenance
________________
PAINT AND TRIM COLORS
Interior trim colors are tan and gray. Seating materials are available in cloth, vinyl and leather.
Soft top colors and codes are: Tan (T) and Black (B).
Exterior paint colors and codes are outlined in the following chart.
REPLACEMENT KEYS
Replacement keys can be cut using Briggs and Stratton or Curtis key cutting tools. Key codes are provided on an identificaion tag
included with each key set (Figure-1-9).
Figure 1-9: Key Code Location
TOWING, LIFTING, JUMP STARTING
Vehicle Lifting/Jacking Points
Vehicle jacking points are shown in Figure 1-10. The vehicle can be raised with a floor jack at any of the indicated positions. Jack-
ing can be performed at the front, rear, or at any one wheel.
In cases where the entire vehicle must be raised, use jack stands at equidistant points on the frame rails. Use a minimum of four
stands to support the vehicle. Suggested capacity for individual jack stands is 3 ton, with a vertical reach of 19 in. (49 cm).
Typical jack stand placement for raising one side of the vehicle is shown in Figure 1-11. Always be sure the jack stand saddle is se-
curely engaged and the stand is level.
Vehicle Hoisting
HUMMER H1 vehicles can be raised on a hoist for service access. Drive-on and swivel arm hoists are both acceptable. Hoist ca-
pacity and width are important. The greater width and weight of HUMMER H1 vehicles require a larger hoisting platform. Do not
use an under capacity hoist, or modify an existing hoist for use; this practice is neither safe nor recommended.
Top Coat Description
AM General Code
Black Gloss
B25
Bright White
W26
Competition Yellow
Y27
Firehouse Red
R28
Metallic Black
B34
Metallic Diamond Black
B30
Metallic Pewter
P33
Metallic Sand
T32
Summit Silver
S31
03-OM2-005
_______________
General Information, Lubrication and Maintenance 1-21
5745804
Figure 1-10: Vehicle Jacking Points
Figure 1-11: Typical Jack Stand Placement
Towing Recommendations
HUMMER H1 vehicles can be towed with wheel lift, sling-type, or flat bed tow equipment.
Flat bed and wheel lift equipment is recommended over sling type or A-frame equipment.
Towing Cautions:
• Remove or secure loads in the towed vehicle
• Never use the shackles on the front bumpers as tie down points
• Always use safety chains on sling towed vehicles
• Always follow the transmission/transfer case shift position recommendations (Transfer Case in N (Neutral); Transmission
in P (Park).
• Use a low vehicle trailer for recreational towing (behind an RV or other vehicle) when possible.
• Never put chains, cables or straps on any steering components.
REAR
CROSSMEMBER
REAR
LOWER
CONTROL
ARMS
FRAME RAIL
FRONT
CROSSMEMBER
FRONT LOWER
CONTROL ARMS
FRAME RAIL
REAR
BUMPER
02-S01-001
JACK STANDS POSITIONED
UNDER FRAME RAIL
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст