Hummer H1 (2006+). Manual — part 290
10-22 Body
______________________________________________________________________
CIGARETTE LIGHTER REPLACEMENT
Removal
1.
Remove the element from the lighter assembly heater (Figure 10-20).
4.
Remove the heater and the bezel from the console using the cigarette lighter socket tool (J-42059).
5.
Remove the wiring harness connector from the lighter assembly
Installation
1.
Install the wiring harness connector on the lighter assembly.
2.
Install the heater in console (Figure 10-20).
3.
Install the element in the lighter assembly.
4.
Engage the cigarette lighter to ensure proper operation.
Figure 10-20: Cigarette Lighter Breakdown
GLOVE BOX REPLACEMENT
Removal
Remove the five screws securing the glove box to the center console and remove the box (Figure 10-21).
Installation
Secure the glove box to the center console with the five screws (Figure 10-21).
WIRING HARNESS
ELEMENT
HEATER
CONSOLE
CONNECTOR
LIGHTER
ASSEMBLY
BEZEL
_____________________________________________________________________
Body 10-23
Figure 10-21: Glove box
ENGINE ACCESS COVER
Inner Engine Access Cover Flexible Latch and Hold-Down Striker Replacement
Removal
1.
Remove the center dash assembly (Refer to secton 10).
2.
Remove the center console (Refer to secton10).
3.
Remove the right side crash pad (Refer to secton10).
4.
Release the two engine cover flexible latches and the two hold down strikers (Figure 10-22).
5.
Remove the rivets from the flexible latches to the cargo floor.
6.
Remove the rivet from the hold down striker to the body (Figure 10-22).
Installation
1.
Secure the flexible latch to the cargo floor with the rivets (Figure 10-22).
2.
Secure the hold down striker to the body with the rivets (Figure 10-22).
3.
Install the engine access cover and secure with the two flexible latches and the two striker latches.
4.
Install the right side crash pad.
5.
Install the center console.
6.
Install the center dash assembly.
Figure 10-22: Inner Engine Access Cover Latch Location
GLOVE BOX
CENTER CONSOLE
FLEXIBLE
BODY
CARGO FLOOR
LATCH
HOLD DOWN
STRIKER
10-24 Body
______________________________________________________________________
Engine Access Cover Replacement
Removal
1.
Remove the center dash assembly.
2.
Remove the center console.
3.
Remove the right side crash pad.
4.
Unlatch the flexible latches from the keepers on the engine access cover hold-down brackets (Figure 10-23).
5.
Unlatch the hold down latches from the engine access cover hold-down strikers.
6.
Turn the ring studs and remove access cover.
Figure 10-23: Engine Access Cover Replacement
Disassembly
1.
Remove the rivets, retainers and the insulation from the engine access cover (Figure 10-24).
2.
Remove the seal from the access cover.
3.
Remove the retaining rings, washers and the ring studs from the access cover (Figure 10-25).
4.
Remove the locknuts and the shoulder bolts securing the latch guide plates and the back plates to the access cover and remove
the latches.
5.
Remove the rivets, latch guide plates and the back plates from the access cover.
6.
Remove the rivets and the keepers from the hold-down brackets.
7.
Remove the rivets, nuts, washers, screws, hold-down brackets and the backing plates from the access cover.
Assembly
1.
Secure the hold-down brackets and the backing plates to access the cover with rivets, screws, washers and the nuts (Figure
10-25).
2.
Secure the keepers to the hold-down brackets with the rivets.
3.
Secure the latch guide plates and the back plates to the access cover with the rivets.
4.
Secure the latch guide plates to the back plates and the access cover with the shoulder bolts and the locknuts. Install latches.
5.
Secure the washers and the ring studs to the access cover with the washers and the retaining rings.
6.
Install the seal on the access cover (Figure 10-24).
7.
Secure the insulation to the access cover with the rivets and the retainers.
ENGINE
FLEXIBLE
RING STUDS
HOLD-DOWN STRIKER
LATCH
ACCESS
COVER
HOLD-DOWN LATCH
_____________________________________________________________________
Body 10-25
Figure 10-24: Engine Access Cover, Insulation and Seal Breakdown
Figure 10-25: Engine Access Cover Fastener Positioning
Installation
1.
Position the engine access cover and the fasten ring studs (Figure 10-25).
2.
Secure the hold-down latches on the hold-down strikers.
3.
Latch the flexible latches on the hold-down bracket keepers.
4.
Install the center dash assembly.
5.
Install the right side crash pad.
6.
Install the center console.
Seat Belt Buckle Assembly Replacement
NOTE: Replacement of the seat belt assembly is basically the same for all seat locations on all the vehicle models. This procedure
covers the left front seat belt buckle on the model 84 vehicle.
Removal
1.
Move the seat to the forward position.
2.
Remove the bolt/washer assembly and the seat belt buckle from the body (Figure 10-26).
3.
Remove the four socket-head screws securing the shifter bezel and remove the bezel.
SEAL
RETAINER
ENGINE ACCESS
COVER
INSULATION
RING STUD
RETAINING
LATCH
HOLD-DOWN LATCH
BACK PLATE
KEEPER
HOLD-DOWN
ENGINE
BRACKET
RINGS
GUIDE
PLATE
ACCESS COVER
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст