Hummer H1 (2006+). Manual — part 190

4-40

Cooling System

__________________________________________________________

7.

Press the input shaft into the GFD (Figure 4-37).

Figure 4-37: Pressing The Input Shaft

8.

Install tool J-8814-11 onto the output flange, apply medium strength thread locker and torque the output shaft nut to 110 lb. ft.
(150 N•m) (Figure 4-30).

9.

With tool J-8814-11 still installed and using tool EN-48032, torque the input shaft nut to 70 lb. ft. (95 N•m) if the lock-washer
tab does not line up, continue to tighten until tab alignment can be achieved. Once alignment is achieved, bend the lock tab in
place to secure the nut.

10. Apply aviation gasket sealant to the sealing surface and install the core plug (Figure 4-31).

11. Apply a thin coat of gear lube on the gerotor pump and install it onto the transfer shaft (Figure 4-28).

12. Install new o-rings on the pump housing, install the relief spring and ball in the rear case, install the pump housing to the rear

case and torque to 9 lb. ft. (12 N•m) (Figure 4-28).

13. Install the sump assembly with a new gasket and torque the bolts to 18.5 lb. ft. (25 N•m).

14. Install the oil pipe and torque the nuts to 19 lb. ft. (26 N•m) (Figure 4-27).

15. Install the GFD and fill with fluid.

BEARING SUPPORT

12-1-05

_________________________________________________________________________________

5-1

5745804

Section 5 Transmission/Transfer Case

TABLE OF CONTENTS

Flywheel and Flexplate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-33
Torque Converter/Oil Pump Seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-30
Transfer Case

Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-69
Cleaning and Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-63
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-39
Diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-42
Disassembly and Overhaul . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-47
Essential Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-88
Extension Housing Bushing and Seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-67
Fluid Change . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-45
Fluid Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-41
Front Output Shaft Bearing and Seal Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-64
Front Output Shaft Seal Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-44
Guide Cable Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-44
Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-40
Input Gear Bearing Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-66
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-47
Lever Knob . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-36
Mainshaft Pilot Bearing Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-67
Oil Cooler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-40
Operating Ranges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-41
Recommended Lubricant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-41
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-45
Shift Control Assembly Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-34
Shifting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-41
Speed Sensor and Switch Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-44
Torque Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-87
Vent Line Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-43

Transmission

Abuse Protection Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-9
Control Valve Solenoid Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-27
Cooler Flushing and flow testing Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-23
Essential Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-88
Fast Learn Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-10
Fill Tube Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-24
Fluid And Filter Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-23
Fluid Checking Procedure (COLD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-11
Fluid Checking Procedure (HOT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-12
Functional Test Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-17
Gear Ratios . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-5
Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-5
Input and Output Speed Sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-6
Input Speed Sensor Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-38
Line Pressure Check Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-19
Mount/Isolator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-37
Neutral Start Back Up (NSBU) Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-7
Neutral Start Backup Switch (NSBU) Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-36
Oil Pan and internal oil filter Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-25

10-1-08

5-2

Transmission/Transfer Case

_________________________________________________

Pressure Control Solenoid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-11
Pressure Switch Manifold Replacement (PSM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-29
Recommended Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-11
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-30
Road Test Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-12
Shift Solenoids . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-8
Special Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-90
Speed Sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
Torque Converter Clutch Solenoid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-11
Torque Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-88
Transmission Control Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-21
Valve Body Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-26
Vehicle Speed Sensor (VSS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
Vent Line Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-24
Warning Lamps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-20

TRANSMISSION DESCRIPTION

The Allison 1000 Series transmission utilizes clutch-to-clutch shift control to achieve range changes. In every case, except shifts to
or from NEUTRAL, one clutch is exhausted and another applied in order to make a range shift. The hand-off between exhausting
and applying clutches is precisely controlled by the use of two pressure proportional to current PPC) solenoids. These solenoids are
labeled A and B in the transmission, and are referred to as trim solenoids. For example, to make a 1-2 shift, pressure control sole-
noid (PC) A is used to trim pressure off the low and reverse clutch, and PC solenoid B is used to trim pressure on the 2nd clutch.
The transmission control module (TCM) modulates the current to both PC solenoid A and PC solenoid B, which translates to a pro-
portional level of pressure to the clutch. In order to make a shift, the TCM uses software and calibration settings of several program
parameters in order to determine the level of current sent to the respective trim solenoids. These parameters are referred to as adap-
tive values. With a new transmission and TCM calibration, the adaptive values are set to a base calibration level. The transmission
uses the base calibration to perform the first of each type of shift. However, once the transmission has performed a shift, the TCM
evaluates the actual shift and compares it to an ideal shift in the TCM memory. Based on that comparison, the TCM changes the
settings of the adaptive values to a level that it believes will result in a shift closer to the ideal shift the next time it makes that type
of shift. This is referred to as adaptive shifting. When the transmission/TCM calibration is new, the TCM is in fast adaptive mode.
The TCM is allowed to make large changes in the adaptive values after each shift. Once the TCM determines that a given shift is
close to the ideal level, it switches to slow adaptive mode. In slow adaptive, the TCM still is evaluating shifts and changing adap-
tive values, but is only allowed to do so in smaller increments. When a shift switches from fast to slow adaptive mode, it is de-
scribed as converged. The TCM is programmed in order to switch from fast to slow adaptive mode in as many as 15-20 shifts. It is
important to understand that there are many different distinct shifts recognized by the TCM and each of these shifts has its own
adaptive values. There are upshifts and downshifts to and from each range, as well as unique adaptive values for several different
throttle regions for each upshift and downshift. It may take a significant amount of time before most of the shifts converge from
fast to slow adaptive and thus it is not unusual to experience somewhat harsh or unpleasant shift quality until these shifts are
adapted.

10-1-08

________________________________________________

Transmission/Transfer Case 5-3

5745804

Torque converter clutch (TCC) engagement is accomplished by a separate pulse width modulated (PWM) solenoid, labeled F in
the transmission. There are adaptive values for this as well and thus it will also require some driving for TCC engagement to con-
verge.

If you are experiencing harsh shifts, it is important to verify whether the particular shift is converged. Use the scan tool in order to
determine if the shift is converged.

• If the shift is not converged, the TCM is learning how to adapt that shift, and needs to be driven more, with the intention of

performing more of the particular type of shift.

• If a particular shift is converged, but still objectionable, it is good troubleshooting practice to reset the adaptive values for

that shift back to base calibration level. This will automatically reset the TCM to fast adaptive mode. The vehicle should
then be driven in order to allow the TCM to relearn the shift. Many times this will correct the condition. It is possible to reset
individual shifts without affecting the other shifts.

NOTE: WHEN REPLACING A FAILED TRANSMISSION WITH A REPLACEMENT UNIT, IT IS IMPORTANT TO RESET
THE TCM TO BASE CALIBRATION AND FAST ADAPTIVE FOR ALL SHIFTS. This can be done in one step with the scan
tool. If this is not done, the TCM adaptive values will be at the settings that it learned for the old transmission and will be in slow
adaptive mode. Under these conditions, it would take an unacceptably long time for the adaptive values to converge to levels suit-
able for the new transmission.

TORQUE CONVERTER

The torque converter is a single-stage, polyphase, and three-element unit, consisting of a pump, stator, and turbine. At lower output
speeds, the torque converter multiplies torque and provides a fluid coupling to the engine. At higher speeds, the torque converter
clutch (TCC) is automatically engaged to provide direct drive from the engine to the transmission. Hydraulic fluid for converter
charging pressure comes from the sump and is supplied by the input pump. The torque converter clutch is applied or released by
changing direction of fluid in the torque converter. An integral converter damper minimizes the need for additional engine vibra-
tion control.

GEAR SETS

The planetary gear train includes three constant-mesh planetary gear sets containing helical gears. By the engagement of the
clutches in various combinations, the planetary sets act singly or together to provide five forward ranges, neutral, and reverse.

CLUTCHES

Five clutches (two rotating and three stationary) direct the flow of torque through the transmission. All range clutches are hydrauli-
cally actuated and spring-released, with automatic wear compensation. The transmission fluid cools the clutches. The transmission
control module (TCM) signals solenoid valves to apply and release clutches based on speed and power combinations and the range
selected by the operator.

HYDRAULIC SYSTEM

A common hydraulic system serves the torque converter and the transmission. Transmission fluid for all hydraulic operations, lu-
brication, and cooling comes from the sump and is supplied by the charging pump.

TRANSMISSION FLUID FILTRATION

Fluid filtration is provided by two filter systems. A suction filter, located in the sump, provides general protection to the entire hy-
draulic system by filtering large particulates. A spin-on filter provides full-time protection for the control solenoids and multipass
protection for the entire system. The spin-on filter is externally located on the converter housing at the lower left front of the trans-
mission.

ELECTRO-HYDRAULIC CONTROL VALVE ASSEMBLY

The control valve assembly consists of two components. The main valve body contains the trim valves, the torque converter clutch
(TCC) valve, the exhaust backfill valve, and the control main relief valve. The shift valve body contains the shift valves, the control
main pressure valve, and the manual selector valve. The control valve assembly attaches to the bottom of the gearbox module and
is enclosed by the oil pan.