Hummer H2. Manual — part 639
z
The window lockout function is disabled and the window lockout signal circuit is shorted to ground.
z
The above condition must be met for 250 milliseconds.
Action Taken When the DTC Sets
The left rear power window will be inoperative from both the driver and passenger power window switches.
Conditions for Clearing the DTC
When the fault is no longer present, the BCM changes the current DTC to a history DTC. The BCM will clear
the history DTC after 50 fault free ignition cycles.
DTC B3821
Step
Action
Yes
No
Schematic Reference: Power Window Schematics
Connector End View Reference:Power Door Systems Connector End Views
1
Did you perform the Door Systems Diagnostic
System Check?
Go to Step 2
Go to Diagnostic
System Check -
Door Systems
2
1. Install a scan tool.
2. Turn ON the ignition, with the engine OFF.
3. Disable the window lockout function.
4. With a scan tool, command the left rear
power window UP and DOWN.
Does the left rear power window operate UP and
DOWN with each command?
Go to Testing for
Intermittent Conditions
and Poor Connections in
Wiring Systems
Go to Step 3
3
1. Turn OFF the ignition.
2. Disconnect the left rear power window
switch.
3. Turn ON the ignition, with the engine OFF.
4. Ensure the window lockout function is
disabled.
5. Probe the window lockout signal circuit with
a test lamp connected to a good ground.
Does the test lamp illuminate?
Go to Testing for
Intermittent Conditions
and Poor Connections in
Wiring Systems
Go to Step 4
4
Test the window lockout signal circuit for a short to
ground. Refer to Circuit Testing and Wiring
Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 7
Go to Step 5
Inspect for poor connections at the harness
connector of the Body Control Module. Refer to
2004 Hummer H2
2004 ACCESSORIES & EQUIPMENT Doors - Hummer H2
DTC B3822
Circuit Description
The Body Control Module (BCM) grounds the control side of the right rear power window up relay upon
receiving a class 2 message from the Driver Door Module (DDM).
Conditions for Running the DTC
z
Battery voltage is between 9.0 and 16 volts.
z
The BCM has received a class 2 message from the DDM and has grounded the right rear power window
relay control circuit.
Conditions for Setting the DTC
z
When the BCM has grounded the right rear power window up relay control circuit and the control circuit
is shorted to battery positive voltage.
z
The above condition is met for 250 milliseconds.
Action Taken When the DTC Sets
The right rear power window will be inoperative from both the driver and right rear power window switches.
Conditions for Clearing the DTC
When the fault is no longer present, the BCM changes the current DTC to a history DTC. The BCM will clear
the history DTC after 50 fault free ignition cycles.
5
Testing for Intermittent Conditions and Poor
Connections and Connector Repairs in Wiring
Systems.
Did you find and correct the condition?
Go to Step 7
Go to Step 6
6
Replace the Body Control Module. Refer to Body
Control Module Replacement in Body Control
System.Did you complete the replacement?
IMPORTANT:
Perform the set up procedure for the Body
Control Module.
Go to Step 7
-
7
1. Use the scan tool in order to clear the DTCs.
2. Operate the vehicle within the Conditions for
Running the DTC as specified in the
supporting text.
Does the DTC reset?
Go to Step 2
System OK
2004 Hummer H2
2004 ACCESSORIES & EQUIPMENT Doors - Hummer H2
Test Description
The numbers below refer to the step numbers on the diagnostic table.
2: Listen for an audible click when the right rear power window relay operates. Command both the ON
and OFF states. Repeat the commands as necessary.
3: Tests for voltage at the coil side of the right rear power window up relay.
4: Verifies that the BCM is providing ground to the right rear power window up relay.
5: Tests if ground is constantly being applied to the right rear power window up relay.
DTC B3822
Step
Action
Yes
No
Schematic Reference: Power Window Schematics
Connector End View Reference:Power Door Systems Connector End Views
1
Did you perform the Door Systems Diagnostic
System Check?
Go to Step 2
Go to Diagnostic
System Check -
Door Systems
2
1. Install a scan tool.
2. Turn ON the ignition, with the engine OFF.
3. With a scan tool, command the right rear
power window up relay ON and OFF.
Does the right rear power window up relay turn ON
and OFF with each command?
Go to Testing for
Intermittent Conditions
and Poor Connections in
Wiring Systems
Go to Step 3
3
1. Turn OFF the ignition.
2. Disconnect the right rear power window
switch.
3. Turn ON the ignition, with the engine OFF.
4. Probe the battery positive voltage circuit of
the right rear power window switch with a
test lamp that is connected to a good ground.
Does the test lamp illuminate?
Go to Step 4
Go to Step 10
4
1. Connect a test lamp between the control
circuit of the right rear power window up
relay and the battery positive voltage circuit
of the right rear power window switch.
2. With a scan tool, command the right rear
power window up relay ON and OFF.
Does the test lamp turn ON and OFF with each
command?
Go to Step 8
Go to Step 5
Does the test lamp remain illuminated with each
2004 Hummer H2
2004 ACCESSORIES & EQUIPMENT Doors - Hummer H2
DTC B3823
Circuit Description
5
command?
Go to Step 7
Go to Step 6
6
Test the control circuit of the right rear power
window up relay for a short to voltage. Refer to
Circuit Testing and Wiring Repairs in Wiring
Systems.
Did you find and correct the condition?
Go to Step 13
Go to Step 9
7
Test the control circuit of the right rear power
window up relay for a short to ground. Refer to
Circuit Testing and Wiring Repairs in Wiring
Systems.
Did you find and correct the condition?
Go to Step 13
Go to Step 9
8
Inspect for poor connections at the right rear power
window switch. Refer to Testing for Intermittent
Conditions and Poor Connections and Connector
Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 13
Go to Step 11
9
Inspect for poor connections at the harness
connector of the Body Control Module. Refer to
Testing for Intermittent Conditions and Poor
Connections and Connector Repairs in Wiring
Systems.
Did you find and correct the condition?
Go to Step 13
Go to Step 12
10
Repair the battery positive voltage circuit of the
right rear power window switch. Refer to Wiring
Repairs in Wiring Systems.
Did you complete the repair?
Go to Step 13
-
11
Replace the right rear power window switch.
Did you complete the replacement?
Go to Step 13
-
12
Replace the Body Control Module. Refer to Body
Control Module Replacement in Body Control
System.Did you complete the replacement?
IMPORTANT:
Perform the set up procedure for the Body
Control Module.
Go to Step 13
-
13
1. Use the scan tool in order to clear the DTCs.
2. Operate the vehicle within the Conditions for
Running the DTC as specified in the
supporting text.
Does the DTC reset?
Go to Step 2
System OK
2004 Hummer H2
2004 ACCESSORIES & EQUIPMENT Doors - Hummer H2
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст