Hummer H2. Manual — part 168
Test Description
The numbers below refer to the step numbers on the diagnostic table.
2: Lack of communication may be due to a partial malfunction of the class 2 serial data circuit or due to a
total malfunction of the class 2 serial data circuit. The specified procedure will determine the particular
condition.
5: Tests for an open in the passlock sensor signal circuit which may not set a DTC B2958 under certain
conditions.
6: The presence of DTCs which begin with "U" indicate some other module is not communicating. The
specified procedure will compile all the available information before tests are performed.
7: The presence of DTC P0601, P0602, P0604, or P0606 indicates an internal fault in the PCM.
8: The presence of DTC B1000 indicates an internal module fault.
9: The Presence of DTC P1637, P1638, P0562 or P0563 indicates a low or high voltage condition.
Diagnostic System Check - Theft Deterrent
Step
Action
Yes
No
Schematic Reference:Theft Deterrent System Schematics
1
Install a scan tool.
Does the scan tool power up?
Go to Step 2
Go to Scan Tool Does Not
Power Up in Data Link
Communications
2
1. Turn ON the ignition, with the
engine OFF.
2. Attempt to establish
communication with the following
control modules:
z
Powertrain Control Module
(PCM)
z
Body Control Module
(BCM)
z
Instrument Panel Cluster
(IPC)
Does the scan tool communicate with
the all the listed control modules?
Go to Step 3
Go to Scan Tool Does Not
Communicate with Class 2
Device in Data Link
Communications
1. Access the Class 2 Power Mode
parameter in the Diagnostic
Circuit Check menu on the scan
IMPORTANT:
Important: The engine may start
during the following step. Turn OFF
the engine as soon as you have
observed the Crank power mode.
2004 Hummer H2
2004 ACCESSORIES & EQUIPMENT Theft Deterrent - Hummer H2
3
tool.
2. Rotate the ignition switch through
all positions while observing the
Class 2 Power Mode parameter.
Does the Class 2 Power Mode parameter
reading match the ignition switch
position for all switch positions?
IMPORTANT:
Insure that all ignition switch
positions are observed
including the OFF position.
Go to Step 4
Go to Power Mode
Mismatch in Body Control
System
4
Select the display DTCs function on the
scan tool for the following control
modules:
z
Powertrain Control Module
(PCM)
z
Body Control Module (BCM)
z
Instrument Panel Cluster (IPC)
Does the scan tool display any DTCs?
Go to Step 6
Go to Step 5
5
1. Momentarily rotate the ignition
switch to CRANK. Do not start
the vehicle.
2. Release the ignition switch to ON.
3. With a scan tool, observe the
Passlock Code in the Body
Control Module Security Data list.
Does the scan tool display OPEN?
Go to DTC B2958
Go to Symptoms - Theft
Deterrent
6
Does the scan tool display any DTCs
which begin with a "U"?
Go to Scan Tool Does Not
Communicate with Class 2
Device in Data Link
Communications
Go to Step 7
7
Does the scan tool display DTC P0601,
P0602, P0604, or P0606?
Go to Diagnostic Trouble
Code (DTC) List in Engine
Controls - 6.0L
Go to Step 8
8
Does the scan tool display DTC B1000? Go to DTC B1000 in Body
Control System
Go to Step 9
Does the scan tool display DTC P1637,
Go to Diagnostic Trouble
2004 Hummer H2
2004 ACCESSORIES & EQUIPMENT Theft Deterrent - Hummer H2
SCAN TOOL DATA LIST
Body Control Module (BCM)
9
P1638, P0562 or P0563?
Code (DTC) List in Engine
Electrical
Go to Diagnostic Trouble
Code (DTC) List
Scan Tool
Parameter
Data List
Units Displayed
Typical
Data Value
Ignition ON/Engine OFF/Vehicle in PARK/Headlamps in AUTO
Auto Learn
Timer
Security
Data
Seconds
0-600
Battery
Voltage
Data
Volts
Varies
Content Theft
Lamp
Security
Data
ON/OFF
OFF
Content Theft
State
Security
Data
ON/OFF
OFF
Door Unlock
Switch
Inputs
ACTIVE/INACTIVE
ACTIVE
Driver Door
Ajar Switch
Inputs
ACTIVE/INACTIVE
ACTIVE
(door open)
Ignition 1
Inputs
ACTIVE/INACTIVE
ACTIVE
Ignition 3
Inputs
ACTIVE/INACTIVE
ACTIVE
Module Part
Number
ID
Information
Numeric
Varies
Passlock Code
Security
Data
Open/Short/Tamper/Numeric
Valid Code
1-10
Passlock Data
Voltage
Security
Data
Volts
0.86-5
Volts
Passlock
Ignition Cycles
Security
Data
Cycles
Varies
Passlock
Power
Security
Data
On/Off
On
Passlock State
Security
Data
Ignition Off/Tamper/Fail Enable/Fail Enable Dec/Seedkey
Lrn Pend/Seedkey Learn/Auto Learn Pend/Learn
Passlock/Monitor Passlock/Normal Decision/Auto Learn
Monitor
Passlock
Security
Calibration
Number
ID
Information
Numeric
Varies
Security Lamp
State
Security
Data
ON/OFF/FLASHING
OFF
Security Suffix
ID
Information
Two Letters
Varies
Seed and Key
Security
2004 Hummer H2
2004 ACCESSORIES & EQUIPMENT Theft Deterrent - Hummer H2
Powertrain Control Module (PCM)
SCAN TOOL DATA DEFINITIONS
Auto Learn Timer
The scan tool displays the seconds used by the BCM to learn valid code from the Passlock(tm) sensor.
The learn procedure consists of 3 consecutive periods.
Battery Voltage
The scan tool displays the battery system voltage.
Content Theft Lamp
The scan tool displays the state of the SECURITY lamp. The scan tool displays ON when activated by an
unauthorized entry.
Content Theft State
The scan tool displays the state of the content theft feature. The scan tool displays ON when activated by
an unauthorized entry.
Door Unlock Switch
The scan tool displays the state of the door key switch. The scan tool displays ACTIVE when the switch
is activated in either door key cylinder.
Drivers Door Ajar Switch
The scan tool displays the position of the drivers door. The scan tool displays ACTIVE when the drivers
door is open.
Ignition 1
Timer
Data
Seconds
0 Seconds
Tamper Timer
Security
Data
Seconds
0-600
Scan Tool Parameter
Data List
Units Displayed
Typical Data Value
Ignition ON/Engine OFF/Vehicle in PARK/Headlamps in AUto
PCM/VCM in VTD Fail Enable
Engine Data 1
Yes/No
No
VTD Auto Learn Timer
Engine Data 1
Active/Inactive
Inactive
VTD Fuel Disable
Engine Data 1
Active/Inactive
Inactive
VTD Fuel Disable Until Ign. OFF
Engine Data 1
Yes/No
No
2004 Hummer H2
2004 ACCESSORIES & EQUIPMENT Theft Deterrent - Hummer H2
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст