Hummer H2. Manual — part 230
z
The PCM detects a TCC brake transition.
z
The PCM does not detect a stop lamp switch transition.
Action Taken When the DTC Sets
z
The PCM sets the stop lamp switch status to released.
z
The PCM disables the operation of the cruise control system.
Conditions for Clearing the DTC
z
A history DTC will clear after 40 malfunction free warm-up cycles.
z
The PCM receives a clear code command from the scan tool.
Diagnostic Aids
Refer to Exterior Lighting Systems Description and Operation in Lighting Systems in order to avoid a
misdiagnosis.
For an intermittent condition, refer to Testing for Intermittent Conditions and Poor Connections in Wiring
Systems.
DTC P1574
Step
Action
Yes
No
Schematic Reference :Cruise Control Schematics
Connector End View Reference: Cruise Control Connector End Views
1
Did you perform the Cruise Control Diagnostic System Check? Go to
Step 2
Go to Diagnostic System
Check - Cruise Control
2
1. Install a scan tool.
2. Turn the ignition ON, with the engine OFF.
3. Depress the brake pedal.
4. With the scan tool, observe the Stoplamp Pedal Switch
parameter in the PCM Cruise Control Data list.
Does the Stoplamp Pedal Switch parameter display Released?
Go to
Step 3
Go to Diagnostic Aids
3
Do the stop lamps operate properly?
Go to
Step 4
Go to Stop Lamps
Inoperative in Lighting
Systems
4
Repair the open or the high resistance in the stop lamp switch
signal circuit. Refer to Circuit Testing and to Wiring Repairs
in Wiring Systems.
Did you complete the repair?
Go to
Step 5
-
1. Use the scan tool in order to clear the DTCs.
2. Operate the vehicle within the conditions for running the
2004 Hummer H2
2004 ACCESSORIES & EQUIPMENT Cruise Control - Hummer H2
SYMPTOMS - CRUISE CONTROL
Visual/Physical Inspection
or
z
Inspect for aftermarket devices which could affect the operation of the Cruise Control System. Refer to
Checking Aftermarket Accessories in Wiring Systems.
z
Inspect the easily accessible or visible system components for obvious damage or conditions which could
cause the symptom.
Intermittent
or
Faulty electrical connections or wiring may be the cause of intermittent conditions. Refer to Testing for
Intermittent Conditions and Poor Connections in Wiring Systems.
Symptom List
Refer to Cruise Control Inoperative/Malfunctioning in order to diagnose a symptom.
CRUISE CONTROL INOPERATIVE/MALFUNCTIONING
Diagnostic Aids
Perform the following in order to avoid a misdiagnosis:
z
Inspect for proper operation of the brake lamps. Refer to Exterior Lighting Systems Description and
Operation in Lighting Systems.
z
EMI on the vehicle speed sensor signal circuit may cause erratic cruise control operation.
5
DTC.
Does the DTC reset?
Go to
Step 2
System OK
IMPORTANT: Perform theDiagnostic System Check - Cruise Control before using the
Symptom Tables in order to verify that all of the following are true:
z
There are no DTCs set.
z
The control modules can communicate via the serial data link.
Review the system description and operation in order to familiarize yourself
with the system functions. Refer to Cruise Control Description and Operation .
2004 Hummer H2
2004 ACCESSORIES & EQUIPMENT Cruise Control - Hummer H2
For an intermittent condition, refer to Testing for Intermittent Conditions and Poor Connections in Wiring
Systems.
Conditions for Enabling Cruise Control
z
The vehicle speed is greater than 40 km/h (25 mph).
z
The vehicle is not in PARK, REVERSE, NEUTRAL, or 1st gear.
z
The system voltage is within 9 volts and 16 volts.
Test description
The numbers below refer to the step numbers on the diagnostic table.
8: This step tests the CHMSL supply voltage/stop lamp supply voltage circuit for an open or for a high
resistance between the stop lamp switch and the TAC module.
9: This step tests the cruise control set/coast switch signal circuit for an open or for a high resistance.
10: This step tests the cruise control resume/accel switch signal circuit for an open or for a high
resistance.
11: This step tests the ignition 3 voltage circuit for an open, for a short to ground, or for a high resistance.
29: DTCs will set in the PCM when you perform this table.
Cruise Control Inoperative/Malfunctioning
Step
Action
Yes
No
Schematic Reference :Cruise Control Schematics
Connector End View Reference:Cruise Control Connector End Views and Powertrain Control
Module (PCM) Connector End Views in Engine Controls- 4.8L, 5.3L, and 6.0L
1
Did you perform the Diagnostic System Check - Cruise
Control?
Go to Step 2
Go to Diagnostic
System Check -
Cruise Control
2
1. Install a scan tool.
2. Turn ON the ignition, with the engine OFF.
3. Turn the cruise control On/Off switch OFF.
4. With the scan tool, observe the Cruise On/Off Switch
parameter in the powertrain control module (PCM)
Cruise Control Data list.
Does the Cruise On/Off Switch parameter display Off?
Go to Step 4
Go to Step 3
3
1. Turn OFF the ignition.
2. Disconnect C4 of the multifunction switch.
3. Turn ON the ignition, with the engine OFF.
4. With the scan tool, observe the Cruise On/Off Switch
parameter.
2004 Hummer H2
2004 ACCESSORIES & EQUIPMENT Cruise Control - Hummer H2
Does the Cruise On/Off Switch parameter display Off?
Go to Step
22
Go to Step 13
4
1. Turn the cruise control On/Off switch ON.
2. With the scan tool, observe the Cruise On/Off Switch
parameter.
Does the Cruise On/Off Switch parameter display On?
Go to Step 5
Go to Step 11
5
1. With the scan tool, observe the Cruise Set/Coast Switch
parameter in the PCM Cruise Control Data list.
2. Turn the cruise control On/Off switch ON.
3. Press and hold the cruise control Set/Coast button.
Does the Cruise Set/Coast Switch parameter Display On?
Go to Step 6
Go to Step 9
6
1. With the scan tool, observe the Cruise Resume/Accel.
Switch parameter in the PCM Cruise Control Data list.
2. Press and hold the Resume/Accel switch.
Does the Cruise Resume/Accel. Switch parameter Display On? Go to Step 7
Go to Step 10
7
Do the stop lamps operate properly?
Go to Step 8
Go to Stop Lamps
Inoperative in
Lighting Systems
8
1. With the scan tool, observe the Stoplamp Pedal Switch
parameter in the PCM Cruise Control Data list.
2. Depress and hold the brake pedal.
Does the Stoplamp Pedal Switch parameter Display Applied?
Go to
Diagnostic
Aids
Go to Step 21
9
1. Turn OFF the ignition.
2. Disconnect C4 of the multifunction switch.
3. Turn ON the ignition, with the engine OFF.
4. Connect a 3 ampere fused jumper between the cruise
control set/coast switch signal circuit and the ignition 3
voltage circuit.
5. With the scan tool, observe the Cruise Set/Coast Switch
parameter.
Does the Cruise Set/Coast Switch parameter Display On?
Go to Step
22
Go to Step 19
10
1. Turn OFF the ignition.
2. Disconnect C4 of the multifunction switch.
3. Turn ON the ignition, with the engine OFF.
4. Connect a 3 ampere fused jumper between the cruise
control resume/accel switch signal circuit and the ignition
2004 Hummer H2
2004 ACCESSORIES & EQUIPMENT Cruise Control - Hummer H2
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст