Hummer H2. Manual — part 715
Fig. 5: Testing Locations On Grid Lines
Courtesy of GENERAL MOTORS CORP.
z
If the test lamp goes out, test the grid line in at least 2 places (1,3) to eliminate the possibility of
bridging the open (2) in the grid line.
MIRRORS - AUTOMATIC DAY-NIGHT INOPERATIVE
Mirrors - Automatic Day-Night Inoperative
Step
Action
Value
(s)
Yes
No
Schematic Reference:Inside Rearview Mirror Schematics
Connector End View Reference:Stationary Windows Connector End Views
1
Did you review the operation of the automatic day-
night feature of the mirrors and perform the
necessary inspections?
-
Go to Step 2
Go to
Symptoms -
Stationary
Windows
2
1. Turn ON the ignition, with the engine OFF.
2. Turn OFF the automatic day-night feature of
the inside rearview mirror.
3. Observe the driver outside rearview mirror.
Does the driver outside rearview mirror remain in a
darken state?
-
Go to Step 20
Go to Step 3
1. Turn ON the automatic day-night feature of
2004 Hummer H2
2004 ACCESSORIES & EQUIPMENT Stationary Windows - Hummer H2
3
the inside rearview mirror.
2. Cover the sensor on the inside rearview mirror
back, facing the front window.
3. Shine a bright light into the sensor on the
inside rearview mirror face, facing the rear
window.
Does the inside rearview mirror darken?
-
Go to Step 4
Go to Step 5
4
While shining a bright light into the sensor on the
mirror face, facing the rear window, observe the
driver outside rearview mirror.
Does the driver outside rearview mirror darken?
-
Go to Testing for
Intermittent
Conditions and
Poor Connections
in Wiring Systems
Go to Step 9
5
1. Turn OFF the ignition.
2. Disconnect the harness connector of the inside
rearview mirror.
3. Measure the resistance between the ground
circuit of the inside rearview mirror and a
good ground.
Is the resistance less than the specified value?
3 ohm
Go to Step 6
Go to Step 18
6
1. Turn ON the ignition, with the engine OFF.
2. Measure the voltage between the ignition
voltage circuit and the ground circuit of the
inside rearview mirror.
Is the voltage within the specified range?
B+
Go to Step 7
Go to Step 19
7
1. Place the transmission in PARK.
2. Measure the voltage between the backup lamp
supply voltage circuit and the ground circuit of
the inside rearview mirror.
Is the voltage less than the specified value?
0.5 V
Go to Step 8
Go to Backup
Lamps Always
On in Lighting
Systems
8
1. Place the transmission in REVERSE.
2. Measure the voltage between the backup lamp
supply voltage circuit and the ground circuit of
the inside rearview mirror.
Is the voltage within the specified range?
B+
Go to Step 15
Go to Step 12
1. Turn OFF the ignition.
2. Disconnect the harness connector C2 of the
driver door module (DDM).
2004 Hummer H2
2004 ACCESSORIES & EQUIPMENT Stationary Windows - Hummer H2
9
3. Turn ON the ignition, with the engine OFF.
4. Turn ON the automatic day-night feature of
the inside rearview mirror.
5. Cover the sensor on the mirror back, facing the
front window.
6. Shine a bright light into the sensor on the
mirror face, facing the rear window.
7. Measure the voltage between the automatic
day-night signal circuit and the low reference
circuit of the driver outside mirror element.
Is the voltage within the specified range?
0.75-
1.5 V
Go to Step 11
Go to Step 10
10
Measure the voltage between the automatic day-
night signal circuit of the driver outside mirror
element and a good ground.
Is the voltage within the specified range?
0.75-
1.5 V
Go to Step 14
Go to Step 13
11
1. Turn OFF the ignition.
2. Disconnect the harness connector C3 of the
DDM.
3. Connect a 3-ampere fused jumper wire
between harness connectors C2 and C3 for the
automatic day-night signal circuit of driver
outside rearview mirror element.
4. Connect a 3-ampere fused jumper wire
between harness connectors C2 and C3 for the
low reference circuit of driver outside rearview
mirror element.
5. Turn ON the ignition, with the engine OFF.
6. Turn ON the automatic day-night feature of
the inside rearview mirror.
7. Cover the sensor on the mirror back, facing the
front window.
8. Shine a bright light into the sensor on the
mirror face, facing the rear window.
9. While shining a bright light into the sensor on
the mirror face, facing the rear window,
observe the driver outside rearview mirror.
Does the driver outside rearview mirror darken?
-
Go to Step 16
Go to Step 17
12
Test the backup lamp supply voltage circuit of the
inside rearview mirror for an open or short to
ground. Refer to Circuit Testing and Wiring
Repairs in Wiring Systems.
-
Go to Backup
Lamps
Inoperative in
Lighting
2004 Hummer H2
2004 ACCESSORIES & EQUIPMENT Stationary Windows - Hummer H2
Did you find and correct the condition?
Go to Step 24
Systems
13
Test the automatic day-night signal circuit of the
driver outside rearview mirror element for an open or
short to ground. Refer to Circuit Testing and
Wiring Repairs in Wiring Systems.
Did you find or correct the condition?
-
Go to Step 24
Go to Step 15
14
Test the low reference circuit of the driver outside
rearview mirror element for an open or high
resistance. Refer to Circuit Testing and Wiring
Repairs in Wiring Systems.
Did you find or correct the condition?
-
Go to Step 24
Go to Step 15
15
Inspect for poor connections at the harness connector
of the inside rearview mirror. Refer to Testing for
Intermittent Conditions and Poor Connections
and Connector Repairs in Wiring Systems.
Did you find and correct the condition?
-
Go to Step 24
Go to Step 21
16
Inspect for poor connections at the harness connector
of the DDM. Refer to Testing for Intermittent
Conditions and Poor Connections and Connector
Repairs in Wiring Systems.
Did you find or correct the condition?
-
Go to Step 24
Go to Step 22
17
Inspect for poor connections at the harness connector
of the driver outside rearview mirror. Refer to
Testing for Intermittent Conditions and Poor
Connections and Connector Repairs in Wiring
Systems.
Did you find or correct the condition?
-
Go to Step 24
Go to Step 23
18
Repair an open or high resistance in the ground
circuit of the inside rearview mirror. Refer to Wiring
Repairs in Wiring Systems.
Did you complete the repair?
-
Go to Step 24
-
19
Repair an open or short to ground in the ignition
voltage circuit of the inside rearview mirror. Refer to
Wiring Repairs in Wiring Systems.
Did you complete the repair?
-
Go to Step 24
-
1. Repair a short to voltage on the automatic day-
night signal circuit of the driver outside
IMPORTANT:
A short to voltage on the automatic day-night
signal circuit of the driver outside rearview mirror
element will cause permanent damage to the
driver outside rearview mirror and the inside
rearview mirror. Both mirrors will have to
replaced. The following actions will need to be
performed:
2004 Hummer H2
2004 ACCESSORIES & EQUIPMENT Stationary Windows - Hummer H2
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст