Hummer H2. Manual — part 2209

2: This step checks the air suspension sensor - LR data parameter.

3: This step tests for the proper operation of the circuit in the high voltage range.

4: This step tests for the proper operation of the circuit in the low voltage range. If the fuse in the jumper
opens upon performing this test, the signal circuit has a short to voltage.

5: This step tests for a short to ground in the 5-volt reference circuit.

7: This step tests the 5-volt reference circuit for the air suspension sensor - LR.

DTC C0626

Step

Action

Values

Yes

No

Schematic Reference: Suspension Controls Schematics

1

Did you perform the Air Suspension System Diagnostic
System Check?

-

Go to Step 2

Go to Diagnostic

System Check -

Air Suspension

2

1. Install a scan tool.

2. Turn ON the ignition, with the engine OFF.

3. With a scan tool, observe the Left Height Sensor

parameter in the data list for the air suspension
module.

Is the Left Height Sensor parameter within the specified
range?

0.3-4.7

V

Go to

Diagnostic

Aids

Go to Step 3

3

1. Turn OFF the ignition.

2. Disconnect the air suspension sensor - LR.

3. Turn ON the ignition, with the engine OFF.

4. With a scan tool, observe the Left Height Sensor

parameter.

Is the Left Height Sensor parameter more than the
specified value?

0.3 V

Go to Step 4

Go to Step 8

4

1. Turn OFF the ignition

2. Connect a 3-ampere fused jumper wire between

the signal circuit of the air suspension sensor-LR
and the low reference circuit of the air suspension
sensor - LR.

3. Turn ON the ignition, with the engine OFF.

4. With a scan tool, observe the Left Height Sensor

parameter.

Is the Left Height Sensor parameter less than the
specified value?

0.3 V

Go to Step 5

Go to Step 9

1. Turn OFF the ignition.

2004 Hummer H2

2004 SUSPENSION Air Suspension - Hummer H2

5

2. Disconnect the fused jumper wire.

3. Turn ON the ignition, with the engine OFF.

4. Test the 5-volt reference circuit voltage of the air

suspension sensor - LR.

Is the Left Height Sensor 5 volt reference voltage greater
than the specified value?

4.7 V

Go to Step 7

Go to Step 6

6

Test the 5-volt reference circuit of the air suspension
sensor-LR for a short to ground. Refer to Circuit
Testing and to Wiring Repairs in Wiring Systems.
Did you find and correct the condition?

-

Go to Step

15

Go to Step 12

7

Test the 5-volt reference circuit of the air suspension
sensor - LR for one of the following conditions:

z

A short to voltage

z

A high resistance

z

An open

Refer to Circuit Testing and to Wiring Repairs in
Wiring Systems.
Did you find and correct the condition?

-

Go to Step

15

Go to Step 11

8

Test the signal circuit of the air suspension sensor - LR
for a short to voltage. Refer to Circuit Testing and to
Wiring Repairs in Wiring Systems.
Did you find and correct the condition?

-

Go to Step

15

Go to Step 12

9

Test the signal circuit of the air suspension sensor - LR
for one of the following conditions:

z

A short to voltage

z

A high resistance

z

An open

Refer to Circuit Testing and to Wiring Repairs in
Wiring Systems.
Did you find and correct the condition?

-

Go to Step

15

Go to Step 10

10

Test the low reference circuit of the air suspension
sensor - LR for one of the following conditions:

z

A high resistance

z

An open

-

2004 Hummer H2

2004 SUSPENSION Air Suspension - Hummer H2

DTC C0631

Circuit Description

The Air Suspension Sensor provides a signal voltage between 0.3 and 4.7 volts to the Air Suspension Module.
This signal voltage represents the wheel's position relative to the body. The Air Suspension Module provides a
5 volt reference and a low reference to the sensor.

Conditions for Running the DTC

At power-up and continuous when ignition is activated.

Refer to Circuit Testing and to Wiring Repairs in
Wiring Systems.
Did you find and correct the condition?

Go to Step

15

Go to Step 12

11

Inspect for poor connections at the harness connector of
the air suspension sensor - LR. Refer to Testing for
Intermittent Conditions and Poor Connections and to
Wiring Repairs in Wiring Systems.
Did you find and correct the condition?

-

Go to Step

15

Go to Step 13

12

Inspect for poor connections at the harness connector of
the air suspension module. Refer to Testing for
Intermittent Conditions and Poor Connections and to
Wiring Repairs in Wiring Systems.
Did you find and correct the condition?

-

Go to Step

15

Go to Step 14

13

Replace the air suspension sensor - LR. Refer to Air
Spring Leveling Sensor Replacement .
Did you complete the replacement?

-

Go to Step

15

-

14

1. Replace the air suspension module. Refer to

Module Assembly Electronic Suspension
Control Replacement .

2. Perform the trim height calibration procedure for

the air suspension module if necessary after Check
the trim height procedure.

Did you complete the replacement?

IMPORTANT:

Always perform the check trim height procedure after
air suspension module replacement.

-

Go to Step

15

-

15

1. Use the scan tool in order to clear the DTCs.

2. Operate the vehicle within the Conditions for

Running the DTC.

Does the DTC reset?

-

Go to Step 2

System OK

2004 Hummer H2

2004 SUSPENSION Air Suspension - Hummer H2

Conditions for Setting the DTC

Air Suspension Module senses a suspension sensor voltage below 0.3 volts or above 4.7 volts.

Action Taken When the DTC Sets

z

Air Suspension functionality is suspended.

z

SERVICE AIR SUSPENSION message is displayed.

Conditions for Clearing the DTC

The DTC will clear when the condition for setting the DTC is removed.

Diagnostic Aids

This DTC is set for a high or low signal to the Air Suspension Module from the Air Suspension Sensor-RR.

Test Description

The numbers below refer to the step numbers on the diagnostic table.

2: Checks the Air Suspension Sensor - RR data parameter.

3: Tests for the proper operation of the circuit in the high voltage range.

4: Tests for the proper operation of the circuit in the low voltage range. If the fuse in the jumper opens
upon performing this test, the signal circuit has a short to voltage.

5: Tests for a short to ground in the 5 volt reference circuit.

7: Test the 5 volt reference circuit for the Air Suspension Sensor - RR.

DTC C0631

Step

Action

Values

Yes

No

Schematic Reference: Suspension Controls Schematics

1

Did you perform the Air Suspension System Diagnostic
System Check?

-

Go to Step 2

Go to Diagnostic

System Check -

Air Suspension

2

1. Install a scan tool.

2. Turn ON the ignition, with the engine OFF.

3. With a scan tool, observe the Right Height Sensor

parameter in the data list for the Air Suspension
Module.

Is the Right Height Sensor parameter within the
specified range?

0.3-4.7

V

Go to

Diagnostic

Aids

Go to Step 3

1. Turn OFF the ignition.

2. Disconnect the Air Suspension Sensor-RR.

2004 Hummer H2

2004 SUSPENSION Air Suspension - Hummer H2