Hummer H2. Manual — part 3
Fig. 1: Identifying Air Bag Simulator (Typical)
Courtesy of FORD MOTOR CO.
AIR BAG SIMULATOR APPLICATION
DRIVER-SIDE AIR BAG MODULE
Removal & Installation (Expedition, Explorer, "E" Series Vans, "F" Series Pickups, Mountaineer, Navigator & Ranger)
1. Disable air bag system. See DISABLING & ACTIVATING AIR BAG SYSTEM . Wait at least one
minute. This time is required for back-up power supply in diagnostic monitor to deplete its stored energy.
2. Ensure front wheels are pointed straight ahead. Remove back cover plugs (if equipped) and air bag
Application
Driver-Side
Passenger-Side
Continental
105-00012
105-00012
Contour & Mystique
105-R0012
105-R0012
Crown Victoria & Grand Marquis
105-R0010
105-R0010
Escort
(1)
& Tracer
105-00012
105-00012
"E" Series Vans
105-R0012
105-R0012
Expedition & Navigator
105-R0012
105-R0012
Explorer & Mountaineer
105-R0012
105-R0012
"F" Series Pickups
105-R0012
105-R0012
Mark VIII
105-R0012
105-R0012
Mustang
105-R0012
105-R0012
Ranger
105-00012
105-00012
Sable & Taurus
105-R0012
105-R0012
Town Car
105-00012
105-00012
Villager
T94P-50-A
T96P-50-A
Windstar
105-R0010
105-R0010
(1)
Including Escort Coupe.
1998 Chevrolet Pickup C1500
GENERAL INFORMATION Air Bag Deactivation Procedures
module retaining bolts. Lift air bag module from steering wheel.
3. Disconnect horn connector. Disconnect air bag module connector. Remove driver-side air bag module
from vehicle. Position air bag module on bench with trim cover facing up.
4. To install, reverse removal procedure. Tighten mounting bolts to specification. See TORQUE
SPECIFICATIONS . Connect battery cable(s). Perform SYSTEM OPERATION CHECK .
Removal & Installation (Continental, Crown Victoria, Grand Marquis, Mark VIII, Mustang, Sable, Taurus & Town
Car)
1. Record preset radio station frequencies. Disconnect negative battery cable. Wait at least one minute. This
time is required for back-up power supply in diagnostic monitor to deplete its stored energy.
2. Remove steering wheel spoke covers (if equipped). Remove back cover plugs and air bag module
retaining bolts and washers. Lift air bag module from steering wheel.
3. Disconnect air bag module, horn and speed control connectors (if equipped). Remove driver-side air bag
module from vehicle. Position air bag module on bench with trim cover facing up.
4. To install, reverse removal procedure. Tighten mounting bolts to specification. See TORQUE
SPECIFICATIONS . Connect negative battery cable. Perform SYSTEM OPERATION CHECK .
Program radio station frequencies.
Removal & Installation (Contour & Mystique)
1. Disconnect negative battery cable. Disconnect positive battery cable. Wait at least one minute. This time
is required for back-up power supply in diagnostic monitor to deplete its stored energy.
2. Remove upper and lower steering column shroud from steering column. Rotate steering wheel to access
driver-side air bag module retaining bolts. Remove driver-side air bag module. Disconnect driver-side air
bag module connector and remove from vehicle. Position air bag module on bench with trim cover facing
up.
3. To install, reverse removal procedure. Tighten mounting bolts to specification. See TORQUE
SPECIFICATIONS . Connect positive battery cable. Connect negative battery cable. Perform SYSTEM
OPERATION CHECK .
Removal & Installation (Escort, Escort Coupe & Tracer)
1. Disconnect negative battery cable. Wait at least one minute. This time is required for back-up power
supply in air bag Electronic Crash Sensor (ECS) module to deplete its stored energy.
2. Ensure front wheels are pointed straight ahead. Remove air bag module retaining bolts. Lift air bag
module from steering wheel. Disconnect air bag module connector. Remove driver-side air bag module
from vehicle. Position air bag module on bench with trim cover facing up.
3. To install, reverse removal procedure. Tighten mounting bolts to specification. See TORQUE
SPECIFICATIONS . Connect negative battery cable. Perform SYSTEM OPERATION CHECK .
Removal & Installation (Windstar)
1. Record preset radio station frequencies. Disconnect negative battery cable. Wait at least one minute. This
time is required for back-up power supply in diagnostic monitor to deplete its stored energy.
1998 Chevrolet Pickup C1500
GENERAL INFORMATION Air Bag Deactivation Procedures
2. Remove back cover plugs and air bag module retaining bolts. Lift air bag module from steering wheel.
Disconnect air bag module and horn connectors. Remove driver-side air bag module from vehicle.
Position air bag module on bench with trim cover facing up.
3. To install, reverse removal procedure. Tighten mounting bolts to specification. See TORQUE
SPECIFICATIONS . Connect negative battery cable. Perform SYSTEM OPERATION CHECK .
Program radio station frequencies.
PASSENGER-SIDE AIR BAG MODULE
Removal & Installation (Continental, Crown Victoria, Grand Marquis & Town Car)
1. Record preset radio station frequencies. Disconnect negative battery cable. Wait at least one minute. This
time is required for back-up power supply in diagnostic monitor to deplete its stored energy.
2. On Crown Victoria and Grand Marquis, unsnap and remove upper instrument panel molding. On Town
Car, open glove box door, release assist cable, press sides inward and lower glove box door to floor. On
Continental, Crown Victoria and Grand Marquis, open glove box door, press sides inward and lower it to
floor. On Continental and Town Car, disconnect passenger-side air bag module connector. On all models,
remove passenger-side air bag module retaining bolts.
3. On Crown Victoria and Grand Marquis, disconnect passenger-side air bag module connector. On all
models, push passenger-side air bag module from inside instrument panel. Remove passenger-side air bag
module without handling edges of trim cover.
4. To install, reverse removal procedure. Ensure wiring harness is not pinched between air bag module and
instrument panel. On Town Car, ensure trim cover retaining clips on back of air bag module are fully
seated in slots. On all models, tighten mounting bolts to specification. See TORQUE
SPECIFICATIONS .
Removal & Installation (Contour & Mystique)
1. Disconnect negative battery cable. Disconnect positive battery cable. Wait at least one minute. This time
is required for back-up power supply in diagnostic monitor to deplete its stored energy.
2. Push sides of glove box inward, and lower glove box to floor. Remove 4 screws, disconnect glove box
light, and remove glove box upper cover. Remove A/C duct.
3. Through glove box opening, remove 2 passenger-side air bag module retaining nuts and 2 retaining bolts.
Disconnect passenger-side air bag module connector. Remove passenger-side air bag module from
vehicle. Position air bag module on bench with trim cover facing up.
4. To install, reverse removal procedure. Tighten mounting bolts and nuts to specification. See TORQUE
SPECIFICATIONS . Perform SYSTEM OPERATION CHECK .
Removal & Installation ("E" Series Vans)
1. Disable air bag system. See DISABLING & ACTIVATING AIR BAG SYSTEM . Wait at least one
minute. This time is required for back-up power supply in diagnostic monitor to deplete its stored energy.
2. Remove right lower instrument panel finish panel and panel reinforcement. Remove 3 passenger-side air
bag module retaining nuts. Carefully slide a flat-blade screwdriver (3/8 x 4") under right bottom edge of
passenger-side air bag door.
1998 Chevrolet Pickup C1500
GENERAL INFORMATION Air Bag Deactivation Procedures
3. Lift upward and separate door from retaining clip. Using hands, lift door upwards and separate door from
remaining clips. Disconnect passenger-side air bag connector and remove passenger air bag module.
Remove 6 offset air bag door retaining clips from instrument panel.
4. To install, reverse removal procedure. Tighten air bag mounting bolts to specification. See TORQUE
SPECIFICATIONS . Install 6 NEW offset retaining clips onto air bag module door. Activate air bag
system. See DISABLING & ACTIVATING AIR BAG SYSTEM . Perform SYSTEM OPERATION
CHECK .
Removal & Installation (Expedition, "F" Series Pickups & Navigator)
1. Disconnect negative battery cable. Disconnect positive battery cable (battery to starter relay cable on "F"
series pickups). Wait at least one minute. This time is required for back-up power supply in diagnostic
monitor to deplete its stored energy.
2. Remove instrument panel relay cover from top, right side of instrument panel. Remove 3 passenger-side
air bag module retaining bolts. Disconnect passenger-side air bag module connector, located in relay
cover opening.
3. Gently pull passenger-side air bag module from instrument panel. To install, reverse removal procedure.
Tighten mounting bolts to specification. See TORQUE SPECIFICATIONS . Perform SYSTEM
OPERATION CHECK .
Removal & Installation (Explorer & Mountaineer)
1. Disconnect negative battery cable. Disconnect battery to starter relay cable. Wait at least one minute. This
time is required for back-up power supply in diagnostic monitor to deplete its stored energy.
2. Open glove box. Push sides of glove box toward each other, and lower glove box to floor. Remove
passenger-side air bag module retaining bolts. Push passenger-side air bag module from behind
instrument panel.
3. Using both hands, gently pull passenger-side air bag module from instrument panel. Disconnect
passenger-side air bag module connector, located on left side of air bag.
4. To install, reverse removal procedure. Tighten mounting bolts to specification. See TORQUE
SPECIFICATIONS . Perform SYSTEM OPERATION CHECK .
Removal & Installation (Escort, Escort Coupe & Tracer)
1. Disconnect negative battery cable. Wait at least one minute. This time is required for back-up power
supply in air bag Electronic Crash Sensor (ECS) module to deplete its stored energy.
2. Push in tabs on glove box door, and lower door. Remove 2 glove box hinge-to-instrument panel bolts.
Remove glove box. Remove 4 passenger-side air bag module bolts. Pull passenger-side air bag module
from instrument panel. Disconnect passenger-side air bag module connector. Remove passenger-side air
bag module from vehicle. Position air bag module on bench with trim cover facing up.
3. To install, reverse removal procedure. Tighten mounting bolts to specification. See TORQUE
SPECIFICATIONS .
Removal & Installation (Mark VIII)
1998 Chevrolet Pickup C1500
GENERAL INFORMATION Air Bag Deactivation Procedures
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст