Hummer H2. Manual — part 411
SCAN TOOL DATA DEFINITIONS
Fob 1 Battery
The scan tool displays OK to indicate a good battery voltage level was last received.
Fob 2 Battery
The scan tool displays OK to indicate a good battery voltage level was last received.
Fob 3 Battery
The scan tool displays OK to indicate a good battery voltage level was last received.
Fob 4 Battery
The scan tool displays OK to indicate a good battery voltage level was last received.
Last Fob Button Pressed
The scan tool displays Dr. Door Unlock, All Door Unlock, Door Lock, indicating the last input received
from a programmed fob.
Last Fob Used
The scan tool displays FOB 1-4 to indicate the number of the last transmitter used
Fob 1 Programmed
The scan tool displays Yes/No. The scan tool displays Yes if a transmitter is programmed to this numeric
position.
Fob 2 Programmed
The scan tool displays Yes/No. The scan tool displays Yes if a transmitter is programmed to this numeric
position.
Fob 3 Programmed
Last Fob Button Pressed
Passenger Door Module Data
Lock, Unlock, Panic
Unlock
Last FOB Used
Passenger Door Module Data
FOB 1-4
FOB 1
Fob 1 Programmed
Passenger Door Module Data
Yes, No
Yes
Fob 2 Programmed
Passenger Door Module Data
Yes, No
Yes
Fob 3 Programmed
Passenger Door Module Data
Yes, No
No
Fob 4 Programmed
Passenger Door Module Data
Yes, No
No
2004 Hummer H2
2004 ACCESSORIES & EQUIPMENT Keyless Entry - Hummer H2
The scan tool displays Yes/No. The scan tool displays Yes if a transmitter is programmed to this numeric
position.
Fob 4 Programmed
The scan tool displays Yes/No. The scan tool displays Yes if a transmitter is programmed to this numeric
position.
SYMPTOMS - KEYLESS ENTRY
Visual/Physical Inspection
z
Inspect for aftermarket devices which could affect the operation of the Remote Keyless Entry System.
Refer to Checking Aftermarket Accessories in Wiring Systems.
z
Inspect the easily accessible or visible system components for obvious damage or conditions which could
cause the symptom.
Intermittent
Faulty electrical connections or wiring may be the cause of intermittent conditions. Refer to Testing for
Intermittent Conditions and Poor Connections in Wiring Systems.
Symptom List
Refer to a symptom diagnostic procedure from the following list in order to diagnose the symptom:
z
Panic Mode Inoperative
z
Keyless Entry System Inoperative
PANIC MODE INOPERATIVE
Panic Mode Inoperative
IMPORTANT: The following steps must be completed before using the symptom tables.
1. Perform Diagnostic System Check - Remote Keyless Entry before using
the Symptom Tables in order to verify that all of the following are true.
z
There are no DTCs set.
z
The control module(s) can communicate via the serial data link.
2. Review the system operation in order to familiarize yourself with the
system functions. Refer to Keyless Entry System Description and
Operation .
Step
Action
Yes
No
1
Did you perform the Diagnostic
System Check?
Go to Diagnostic System
Check - Remote Keyless
2004 Hummer H2
2004 ACCESSORIES & EQUIPMENT Keyless Entry - Hummer H2
KEYLESS ENTRY SYSTEM INOPERATIVE
Keyless Entry System Inoperative
Go to Step 2
Entry
2
With the keyless entry
transmitter, attempt to operate
the panic function.
Do both the horns and the park
lamps pulse on and off?
Go to Testing for Intermittent
Conditions and Poor Connections
in Wiring Systems
Go to Step 3
3
Do any of the panic functions
operate?
Go to Step 4
Go to Keyless Entry
System Inoperative
4
Do the horns pulse on and off?
Go to Diagnostic System Check -
Lighting Systems in Lighting
Systems
Go to Diagnostic System
Check - Horns in Horns
Step
Action
Yes
No
1
Did you perform the Diagnostic System Check?
Go to Step 2
Go to Diagnostic
System Check -
Remote Keyless
Entry
2
Press each button of the transmitter one at a time.
Does the system operate normally?
Go to Testing for
Intermittent Conditions
and Poor Connections in
Wiring Systems
Go to Step 3
3
Lock and unlock the door locks using the controls
inside the vehicle.
Do the locks operate properly?
Go to Step 4
Go to Diagnostic
System Check -
Door Systems in
Doors
4
1. Turn on the J 43241 Keyless Entry Tester.
See Special Tools and Equipment .
2. Place the transmitter on the J 43241 test pad.
See Special Tools and Equipment .
3. Press each button of the transmitter one at a
time.
Does a tone sound and the green light illuminate on
the J 43241 after each button is pressed? See
Special Tools and Equipment .
IMPORTANT:
Inspect that the keyless entry transmitter is the
correct model for the vehicle remote system. A
wrong model transmitter may pass this test but
will not activate the vehicle remote system.
Go to Step 8
Go to Step 5
Do any of the buttons on the transmitter sound the
2004 Hummer H2
2004 ACCESSORIES & EQUIPMENT Keyless Entry - Hummer H2
REPAIR INSTRUCTIONS
TRANSMITTER BATTERY REPLACEMENT
Removal Procedure
Under normal use, the battery in the transmitter will last about 2 years, form battery replacement, use a
Panasonic 3 volt, type CR2032, or the equivalent.
1. In order to open the transmitter case, perform the following steps:
1. Insert a dime between the two halves of the transmitter near the key ring hole.
5
tone and illuminate the green light when pressed?
Go to Step 9
Go to Step 6
6
Replace the transmitter battery. Refer to
Transmitter Battery Replacement .
Did you complete the replacement?
Go to Step 7
-
7
1. Turn on the J 43241 Keyless Entry Tester.
See Special Tools and Equipment .
2. Place the transmitter on the J 43241 test pad.
See Special Tools and Equipment .
3. Press each button of the transmitter one at a
time.
Does a tone sound and the green light illuminate on
the J 43241 after each button is pressed? See
Special Tools and Equipment .
Go to Step 8
Go to Step 9
8
Perform the transmitter synchronization procedure.
Refer to Transmitter Resynchronization .
Did the locks cycle to lock then unlock?
Go to Step 12
Go to Step 10
9
Replace the transmitter.
Did you complete the replacement?
Go to Step 10
-
10
Perform the transmitter programming procedure.
Refer to Transmitter Programming .
Did the locks cycle to lock then unlock?
Go to Step 12
Go to Step 11
11
Replace the PDM. Refer to Switch Replacement -
Door Lock and Side Window - Passenger in
Doors.Did you complete the replacement?
IMPORTANT:
When replacing the Passenger Door Module
(PDM), perform the Program all Transmitters
procedure. Refer to Transmitter Programming .
Go to Step 12
-
12
Operate the system in order to verify the repair.
Did you correct the condition?
System OK
Go to Step 3
2004 Hummer H2
2004 ACCESSORIES & EQUIPMENT Keyless Entry - Hummer H2
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст