Hummer H2. Manual — part 693
Rear Window Defogger Grid Terminal Identification - C1
Rear Window Defogger Grid Terminal Identification - C2
6
D-GN/WH
636
Ambient Air Temperature Sensor Signal
7
BK/WH
1704
Low Reference
8
BK
1050
Ground
9
L-GN
24
Backup Lamp Supply Voltage
10-12
-
-
Not Used
13
BN
341
Ignition 3 Voltage
14-15
-
-
Not Used
16
PK
1691
Automatic Day/Night Mirror Low Reference
Connector Part Information
z
12059885
z
1-Way M Metri-Pack 480 Series (BK)
Pin
Wire Color
Circuit No.
Function
A
PU
293
Rear Defog Element Supply Voltage
2004 Hummer H2
2004 ACCESSORIES & EQUIPMENT Stationary Windows - Hummer H2
DIAGNOSTIC INFORMATION AND PROCEDURES
DIAGNOSTIC STARTING POINT - STATIONARY WINDOWS
For the inside rearview mirror with the automatic day-night feature, begin the diagnosis by reviewing the
system Description and Operation. Reviewing the Description and Operation information will help you
determine the correct symptom diagnostic procedure when a malfunction exists. Reviewing the Description and
Operation information will also help you determine if the condition described by the customer is normal
operation. Refer to Symptoms - Stationary Windows in order to identify the correct procedure for diagnosing
the system and where the procedure is located.
For the rear window defogger, begin the diagnosis with the Diagnostic System Check - Defogger . The
Diagnostic System Check will provide the following information:
z
The identification of the control modules which command the system
z
The ability of the control modules to communicate through the serial data circuit
z
The identification of any stored diagnostic trouble codes (DTCs) and their status
The use of the Diagnostic System Check will identify the correct procedure for diagnosing the system and
where the procedure is located.
DIAGNOSTIC SYSTEM CHECK - DEFOGGER
Test Description
Connector Part Information
z
12059885
z
1-Way M Metri-Pack 480 Series (BK)
Pin
Wire Color
Circuit No.
Function
A
BK
1450
Ground
2004 Hummer H2
2004 ACCESSORIES & EQUIPMENT Stationary Windows - Hummer H2
The numbers below refer to the step numbers on the diagnostic table.
2: Lack of communication may be due to a partial malfunction of the class 2 serial data circuit. The
specified procedure will determine the particular condition.
4: The Symptom Table will determine the correct diagnostic procedure to use.
5: The presence of DTCs which begin with "U" indicate some other module is not communicating. The
specified procedure will compile all the available information before tests are performed.
Diagnostic System Check - Defogger
Step
Action
Yes
No
1
Install a scan tool.
Does the scan tool power up?
Go to Step 2
Go to Scan Tool Does
Not Power Up in Data
Link Communications
2
1. Turn ON the ignition, with the engine OFF.
2. Attempt to establish communication with
the following:
z
HVAC Control Module
z
Body Control Module (BCM)
Does the scan tool communicate with the
modules?
Go to Step 3
Go to Scan Tool Does
Not Communicate
with Class 2 Device in
Data Link
Communications
3
1. Access the Class 2 Power Mode in the
Diagnostic Circuit Check on the scan tool.
2. Rotate the ignition switch through all
positions while observing the Class 2 Power
Mode on the Scan Tool. Refer to the Serial
Data Power Mode table within the Body
Control System Description and
Operation in Body Control System, for a
list of the power mode states that correspond
to each ignition switch position.
Does the Class 2 Power Mode parameter reading
match the ignition switch position for all the
selected positions?
IMPORTANT:
The engine may start during the following step.
Turn OFF the engine as soon as you have
observed the Crank power mode.
Go to Step 4
Go to Power Mode
Mismatch in Body
Control System
4
Select the display DTCs function on the scan tool
for the following modules.
z
HVAC Control Module.
2004 Hummer H2
2004 ACCESSORIES & EQUIPMENT Stationary Windows - Hummer H2
SCAN TOOL OUTPUT CONTROLS
Body Control Module (BCM)
SCAN TOOL DATA LIST
Body Control Module (BCM)
SCAN TOOL DATA DEFINITIONS
Body Control Module (BCM)
Rear Defog Relay
The scan tool displays On or Off. When the BCM energizes the RR DEFOG relay, the scan tool will
display On. When the BCM de-energizes the RR DEFOG relay, the scan tool will display Off.
DIAGNOSTIC TROUBLE CODE (DTC) LIST
Diagnostic Trouble Code (DTC) List
DTC B0283
z
BCM
Does the scan tool display any DTCs?
Go to Step 5
Go to Symptoms -
Stationary Windows
5
Does the scan tool display DTCs that begin with
"U"?
Go to Diagnostic
Trouble Code (DTC)
List in Data Link
Communications
Go to Step 6
6
Does the scan tool display DTC B1000 or B1440?
Go to Diagnostic
Trouble Code (DTC)
List in Body Control
System
Go to Diagnostic
Trouble Code (DTC)
List
Scan Tool
Output Control
Additional Menu
Selection(s)
Description
Rear Defogger
-
The BCM actuates the rear window defogger relay when you
select ON. The rear window defogger grid should become warm.
Scan Tool Parameter
Data List
Units Displayed
Typical Data Value
Ignition On/Engine Off
Rear Defog Relay
Outputs
On/Off
Off
DTC
Diagnostic Procedure
Module(s)
B0283
DTC B0283
BCM
2004 Hummer H2
2004 ACCESSORIES & EQUIPMENT Stationary Windows - Hummer H2
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст