Hummer H2. Manual — part 202
Turn the ignition OFF while programming the GDO transmitter. Follow these steps to program up to 3
channels:
1. If you have previously programmed a transmitter, proceed to Step 2. Otherwise, hold down the 2 outside
buttons on the GDO transmitter for approximately 20 seconds, until the light on the GDO transmitter
begins to flash rapidly. Then release the buttons. This procedure erases any previous settings and
initializes the memory for all 3 channels.
2. Decide which of the 3 channels you want to program to the transmitter you have.
3. Hold the end of the hand-held transmitter against the front surface of the GDO (less than 1 inch) so you
can still see the light.
4. Using both hands, press the hand-held transmitter button and the desired button on the GDO transmitter.
Continue to hold both buttons through Step 5.
5. Hold down the buttons on both transmitters until you see the light on the GDO transmitter flash slowly
and then rapidly. The rapid flashing, which could take up to 90 seconds, indicates that the GDO
transmitter has been programmed. Release the buttons on both transmitters when the light starts to flash
rapidly.
Training the GDO for Rolling Code Receivers
This procedure is for training the customer's rolling code garage door openers to their GDO transmitter. The
GDO must already be programmed to its hand-held transmitter. The training process below must be completed
within 30 seconds or it must be repeated.
1. Locate the train button on the garage door opener receiver. Refer to the operator's manual for the garage
door opener (or call HomeLink(tm) at 1-800-355-3515 for assistance). Follow instructions for the garage
door opener in order to determine when the unit is in train mode.
2. Return to the GDO transmitter in the vehicle, and press the button that you want trained for rolling codes
3 times, for 1 second each time. If not successfully programmed, try 2-5 seconds each time.
3. Press the button used again in order to verify that the GDO transmitter has been programmed.
You may use either the hand-held transmitter or the GDO to open the garage door.
The GDO is compatible with most, but not all, types and brands of transmitters. If the GDO light does not flash
rapidly after 90 seconds, there may be a compatibility conflict with the transmitter used to program the GDO.
Call HomeLink(tm) at 1-800-355-3515 in order to address compatibility concerns.
Erasing Channels
IMPORTANT: The GDO is compatible with most, but not all, types and brands of
transmitters. If the GDO light does not flash rapidly after 90 seconds,
there may be a compatibility conflict with the transmitter used to program
the GDO. Call HomeLink(tm) at 1-800-355-3515 in order to address this
problem.
2004 Hummer H2
2004 ACCESSORIES & EQUIPMENT Garage Door Opener - Hummer H2
To erase programmed channels, hold down the 2 outside buttons until the light on the GDO transmitter begins
to flash. Individual channels cannot be erased, but can be reprogrammed using the Garage Door Opener
Programming and the Training GDO for Rolling Code Receivers procedures.
Non-Compatible Garage Door Openers
DESCRIPTION AND OPERATION
GARAGE DOOR OPENER DESCRIPTION AND OPERATION
The garage door opener is located in the overhead console. The valet switch provides battery voltage to the
garage door opener. If battery voltage is lost due to a condition such as a dead battery, the garage door opener
unit relies on the non-servicable internal power backup supply. The unit is programmed using the customer's
hand-held transmitters for the garage doors, electric entrance gates, or lighting and security systems.
The garage door opener is rolling code capable. Rolling code is a system that allows the code that the customers
receiver receives from the garage door opener to change every time the garage door opener is used within
operating range of the receiver. When the receiver and the garage door opener are initially programmed
together, a code is established, a new code is created for every new transmission. The software in the receiver
recognizes the garage door opener and accepts the new code.
The garage door opener is compatible with most, but not all types and brands of transmitters. If a problem
should occur with a compatibility conflict with a transmitter, call HomeLink(tm) at 1-800-355-3515.
The garage door opener is a transmitter operating between 288-399 MHz. The power and range of the
transmitter is limited to comply with laws governing the generation of radio frequency interference (RFI). The
Manufacturer
Model Number
Chamberlain
G-3467
Click Card
ATDG-90
Genie
AR-55
Genie
AR-30
Linear
Code Red
Linear
Moore-o-matic
Linear
DX Format
Micom
Safeway
Pulsar/Allister
20
Skylink
Skylink
Stanley
1048
Stanley
1054
Stanley
1064
Telectron
T-22A
Telectron
T-80
Telectron
T-80G
Telectron
TP-21
2004 Hummer H2
2004 ACCESSORIES & EQUIPMENT Garage Door Opener - Hummer H2
transmitter is programmed by the user to accept the signal generated by the user's transmitters, refer to Garage
Door Opener Programming - Universal .
The garage door opener has 3 buttons that may be programmed for individual transmitter/receiver combinations
to control up to 3 garage door openers, security gates, and lighting systems. Each button represents a transmitter
code section of the transmitter, which operates separately from any other button, and may be considered a
separate transmitter. Operation consists of simply pressing a button to activate the corresponding transmitter.
Battery voltage is provided to the garage door opener from the IGN SEN fuse in the IP fuse block. The garage
door opener is grounded through G400. Inadvertent power is supplied from the body control module (BCM).
SPECIAL TOOLS AND EQUIPMENT
SPECIAL TOOLS
Special Tools
Illustration
Tool Number/Description
J 41540
HomeLink Tester
2004 Hummer H2
2004 ACCESSORIES & EQUIPMENT Garage Door Opener - Hummer H2
2004 ACCESSORIES & EQUIPMENT
Power Outlets - Hummer H2
SCHEMATIC AND ROUTING DIAGRAMS
CIGAR LIGHTER/AUXILIARY OUTLETS SCHEMATICS
Fig. 1: Cigar Lighter/Auxiliary Outlets
Courtesy of GENERAL MOTORS CORP.
COMPONENT LOCATOR
POWER OUTLET COMPONENT VIEWS
2004 Hummer H2
2004 ACCESSORIES & EQUIPMENT Power Outlets - Hummer H2
2004 Hummer H2
2004 ACCESSORIES & EQUIPMENT Power Outlets - Hummer H2
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст