Hummer H2. Manual — part 193
To erase programmed channels, hold down the 2 outside buttons until the light on the GDO transmitter begins
to flash. Individual channels cannot be erased, but can be reprogrammed using the Garage Door Opener
Programming and the Training GDO for Rolling Code Receivers procedures.
Non-Compatible Garage Door Openers
DESCRIPTION AND OPERATION
GARAGE DOOR OPENER DESCRIPTION AND OPERATION
The garage door opener is located in the overhead console. The valet switch provides battery voltage to the
garage door opener. If battery voltage is lost due to a condition such as a dead battery, the garage door opener
unit relies on the non-servicable internal power backup supply. The unit is programmed using the customer's
hand-held transmitters for the garage doors, electric entrance gates, or lighting and security systems.
The garage door opener is rolling code capable. Rolling code is a system that allows the code that the customers
receiver receives from the garage door opener to change every time the garage door opener is used within
operating range of the receiver. When the receiver and the garage door opener are initially programmed
together, a code is established, a new code is created for every new transmission. The software in the receiver
recognizes the garage door opener and accepts the new code.
The garage door opener is compatible with most, but not all types and brands of transmitters. If a problem
should occur with a compatibility conflict with a transmitter, call HomeLink(tm) at 1-800-355-3515.
The garage door opener is a transmitter operating between 288-399 MHz. The power and range of the
transmitter is limited to comply with laws governing the generation of radio frequency interference (RFI). The
Manufacturer
Model Number
Chamberlain
G-3467
Click Card
ATDG-90
Genie
AR-55
Genie
AR-30
Linear
Code Red
Linear
Moore-o-matic
Linear
DX Format
Micom
Safeway
Pulsar/Allister
20
Skylink
Skylink
Stanley
1048
Stanley
1054
Stanley
1064
Telectron
T-22A
Telectron
T-80
Telectron
T-80G
Telectron
TP-21
2004 Hummer H2
2004 ACCESSORIES & EQUIPMENT Garage Door Opener - Hummer H2
transmitter is programmed by the user to accept the signal generated by the user's transmitters, refer to Garage
Door Opener Programming - Universal .
The garage door opener has 3 buttons that may be programmed for individual transmitter/receiver combinations
to control up to 3 garage door openers, security gates, and lighting systems. Each button represents a transmitter
code section of the transmitter, which operates separately from any other button, and may be considered a
separate transmitter. Operation consists of simply pressing a button to activate the corresponding transmitter.
Battery voltage is provided to the garage door opener from the IGN SEN fuse in the IP fuse block. The garage
door opener is grounded through G400. Inadvertent power is supplied from the body control module (BCM).
SPECIAL TOOLS AND EQUIPMENT
SPECIAL TOOLS
Special Tools
Illustration
Tool Number/Description
J 41540
HomeLink Tester
2004 Hummer H2
2004 ACCESSORIES & EQUIPMENT Garage Door Opener - Hummer H2
2004 ACCESSORIES & EQUIPMENT
Power Outlets - Hummer H2
SCHEMATIC AND ROUTING DIAGRAMS
CIGAR LIGHTER/AUXILIARY OUTLETS SCHEMATICS
Fig. 1: Cigar Lighter/Auxiliary Outlets
Courtesy of GENERAL MOTORS CORP.
COMPONENT LOCATOR
POWER OUTLET COMPONENT VIEWS
2004 Hummer H2
2004 ACCESSORIES & EQUIPMENT Power Outlets - Hummer H2
2004 Hummer H2
2004 ACCESSORIES & EQUIPMENT Power Outlets - Hummer H2
Fig. 2: Auxiliary Power Outlets - Front/Rear Console Component Views
Courtesy of GENERAL MOTORS CORP.
Callouts For Fig. 2
Callout
Component Name
1
Auxiliary Power Outlet - Front 1
2
Auxiliary Power Outlet - Front 2
3
Auxiliary Power Outlet - Console
4
Auxiliary Power Outlet - Console
5
Cigar Lighter
2004 Hummer H2
2004 ACCESSORIES & EQUIPMENT Power Outlets - Hummer H2
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст