Hummer H2. Manual — part 1506
1
Did you perform the Inspection/Maintenance (I/M)
System Check?
Go to Step 2
Go to
Inspection/Maintenance
(I/M) System Check
2
1. Ensure the vehicle is within the Conditions for
Running specified in the supporting text.
2. Turn OFF all of the accessories, including the
A/C and the blower fan.
3. Start and idle the engine.
4. Acceleration at part throttle to 72 km/h (45
mph) with this speed maintained until the
engine reaches operating temperature. This
may be up to 8-10 minutes, depending on the
startup coolant temperature.
5. Continue the operating conditions for an
additional 3 minutes after the engine reaches
the operating temperature.
6. Decelerate to 0 km/h (0 mph).
7. Idle the engine for 2 minutes.
8. Turn OFF the ignition for 1 hour.
9. After 1 hour, turn ON the ignition.
10. Observe the EVAP System Status with a scan
tool.
Did the EVAP System Status update to YES?
IMPORTANT:
Once the engine is started, DO NOT turn the
engine OFF for the remainder of the
procedure until the test is complete.
CAUTION:
Refer to Road Test Caution in Cautions and
Notices.
IMPORTANT:
In order for this test to run, the vehicle must
operate in the following conditions:
Go to Step 5
Go to Step 3
3
Observe the DTC Information with a scan tool.
Does the scan tool indicate any failed DTCs?
Go to
Diagnostic
Trouble Code
(DTC) List
Go to Step 4
2004 Hummer H2
2004 ENGINE PERFORMANCE Engine Controls (Troubleshooting) - 4.8L, 5.3L, and 6.0L - Hummer H2
INSPECTION/MAINTENANCE (I/M) HEATED OXYGEN SENSOR/OXYGEN SENSOR (HO2S/O2S)
SYSTEM SET PROCEDURE
Description
The purpose of this test is to satisfy the enable criteria necessary to execute inspection/maintenance (I/M)
readiness diagnostics for the oxygen sensor (O2S, HO2S) system. The test may be used to set the I/M System
Status to YES. The I/M System Status display on the scan tool provides an indication of whether the control
module has completed the required tests. The I/M System Status does not indicate that the tests have passed or
failed. When all of the diagnostics for a specific system have run and passed, the I/M System Status will update
to YES. If a test for a specific system has failed, the I/M System Status will update to YES, indicating a
determination was made, even if all of the other tests for that system have not run.
Conditions for Running
z
DTCs P0133, P0135, P0136, P0140, P0141, P0153, P0155, P0156, P0160, P0161, P1133, P1134, P1153,
P1154 are not set.
z
The fuel level is more than 10 percent.
4
1. Refer to Inspection/Maintenance (I/M)
System DTC Table to determine which DTCs
are required to run in order to complete this
test.
2. Observe the Not Ran Since Code Cleared
display with a scan tool.
3. Determine which of the DTCs required for a
YES status has not run.
4. Enter the DTC number in the Specific DTC
menu of the scan tool.
5. Operate the vehicle within the Conditions for
Running the DTC, located in the supporting
text for the diagnostic table of the DTC.
6. Repeat the procedure until the scan tool
indicates the diagnostic test has run.
7. Repeat steps 4-6 for any additional required
DTCs that have not run.
8. Observe the I/M System Status display with a
scan tool.
Did the EVAP System Status update to YES?
Go to Step 5
Go to Diagnostic Aids
5
Observe the Emission Related DTC portion of the
I/M System Status display with a scan tool.
Does the scan tool indicate any Emission Related
DTCs set?
Go to
Diagnostic
Trouble Code
(DTC) List
System OK
2004 Hummer H2
2004 ENGINE PERFORMANCE Engine Controls (Troubleshooting) - 4.8L, 5.3L, and 6.0L - Hummer H2
z
The engine coolant temperature (ECT) is more than 60°C (140°F).
z
The engine is running in Closed Loop fuel control.
z
The engine has been running for more than 3 minutes.
z
The battery voltage is between 10-18 volts.
z
The mass air flow (MAF) is between 20-55 grams per second.
z
The engine speed is between 1,200-3,000 RPM.
z
The throttle position (TP) sensor is more than 5 percent.
Diagnostic Aids
If there is an impending failure, the system may require more time to run the diagnostic than was allotted in the
set procedure. If the test does not run after numerous attempts and no DTC is set, review the appropriate scan
tool data list and the service information for an indication of why the test does not complete. Some tests may
abort due to changes in the conditions while the test is running. For example, changes in engine load such as a
cooling fan or A/C compressor clutch turning ON may cause the test to abort.
Inspection/Maintenance (I/M) Heated Oxygen Sensor/Oxygen Sensor (HO2S/O2S) System Set Procedure
Step
Action
Yes
No
1
Did you perform the Inspection/Maintenance (I/M)
System Check?
Go to Step 2
Go to
Inspection/Maintenance
(I/M) System Check
2
1. Ensure the vehicle is within the Conditions
for Running specified in the supporting text.
2. Turn OFF all of the accessories, e.g., A/C,
blower fan, etc.
3. Start the engine and allow it to idle for 1
minute.
4. Acceleration at part throttle to 75-90 km/h
(45-55 mph) with this speed maintained for
6 minutes or until the I/M System Status
updates to YES.
Manual transmissions, either 5 or 6 speed,
may require operation in 4th or 5th gear
CAUTION:
Refer to Road Test Caution in Cautions
and Notices.
IMPORTANT:
In order for this test to run, the vehicle
must operate in the following conditions:
2004 Hummer H2
2004 ENGINE PERFORMANCE Engine Controls (Troubleshooting) - 4.8L, 5.3L, and 6.0L - Hummer H2
INSPECTION/MAINTENANCE (I/M) HEATED OXYGEN SENSOR (HO2S) HEATER SYSTEM SET
PROCEDURE
Description
The purpose of this test is to satisfy the enable criteria necessary to execute inspection/maintenance (I/M)
readiness diagnostics for the heated oxygen sensor (HO2S) heater system. The test may be used to set the I/M
respectively, in order for this test to run.
5. Review the I/M System Status display with
a scan tool.
Did the HO2S/O2S System Status update to YES?
Go to Step 5
Go to Step 3
3
Observe the DTC Information with a scan tool.
Does the scan tool indicate any failed DTCs?
Go to
Diagnostic
Trouble Code
(DTC) List
Go to Step 4
4
1. Refer to the Inspection/Maintenance (I/M)
System DTC Table to determine which
DTCs are required to run in order to
complete this test.
2. Observe the Not Ran Since Code Cleared
display with a scan tool.
3. Determine which of the DTCs required for a
YES status has not run.
4. Enter the DTC number in the Specific DTC
menu of the scan tool.
5. Operate the vehicle within the Conditions
for Running the DTC, located in the
supporting text for the diagnostic table of
the DTC.
6. Repeat the procedure until the scan tool
indicates the diagnostic test has run.
7. Repeat steps 4-6 for any additional required
DTCs that have not run.
8. Observe the I/M System Status display with
a scan tool.
Did the HO2S/O2S System Status update to YES?
Go to Step 5
Go to Diagnostic Aids
5
Observe the Emission Related DTC portion of the
I/M System Status display with a scan tool.
Does the scan tool indicate any Emission Related
DTCs set?
Go to
Diagnostic
Trouble Code
(DTC) List
System OK
2004 Hummer H2
2004 ENGINE PERFORMANCE Engine Controls (Troubleshooting) - 4.8L, 5.3L, and 6.0L - Hummer H2
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст