Hummer H2. Manual — part 362
Engine Speed
Cruise Control
Data
Engine Data 1
Engine Data 2
Enhanced EVAP
Data
Fuel Trim Data
HO2S Data
TAC Data
RPM
+/-100 RPM from
Desired Idle Speed
Fuel Level Sensor
Engine Data 1
Enhanced EVAP
Data
Volts
0-5 Volts (Varies)
Fuel Level Sensor Rear Tank (If
Equipped)
Engine Data 1
Enhanced EVAP
Data
Volts
0-5 Volts (Varies)
Fuel Tank Level Remaining
Enhanced EVAP
Data
Liters (Gallons)
Varies
Fuel Tank Level Remaining
Enhanced EVAP
Data
Percent
0-100% (Varies)
Fuel Tank Rated Capacity
Enhanced EVAP
Data
Liters (Gallons)
Varies
Ignition 1 Signal
Cruise Control
Data
Engine Data 1
Engine Data 2
Enhanced EVAP
Data
Fuel Trim Data
TAC Data
Volts
9-16 Volts (Varies)
Low Oil Lamp Command
Engine Data 2
On/Off
Off
MIL (Malfunction Indicator
Lamp) Command
Engine Data 2
On/Off
Off
Reduced Engine Power
Engine Data 1
Active/Inactive
Inactive
Trans. Fluid Temp
Trans Data
Celsius (Fahrenheit)
85-105°C (185-220°F)
(Varies)
Vehicle Speed Sensor
Cruise Control
Data
Engine Data 1
Engine Data 2
Enhanced EVAP
Data
Fuel Trim Data
HO2S Data
Misfire Data
TAC Data
Kilometers per hour (Miles
per hour)
0 km/h (0 mph)
2004 Hummer H2
2004 ACCESSORIES & EQUIPMENT Instrument Panel, Gauges, and Console - Hummer H2
Radio
SCAN TOOL DATA DEFINITIONS
4WD
The scan tool displays On or Off. This is the state of the 4WD indicator as commanded by the instrument
panel cluster (IPC).
ABS Lamp
The scan tool displays On or Off. This is the state of the ABS indicator as commanded by the IPC.
Annual Mileage
The scan tool displays 0.0 to 999999.9 miles (0.0 to 999999.9 kilometers). The DIC determines annual
mileage travelled from the 4 kppm vehicle speed signal circuit from the PCM.
Balance
The scan tool displays 0-100%. The Balance between the right and left audio output.
Battery
The scan tool displays On or Off. This is the state of the charge indicator as commanded by the IPC.
Battery Voltage
The scan tool displays 0-18 volts. This is the voltage at the battery positive voltage circuit of the BCM.
Battery Voltage
The scan tool displays 0-19 volts. The battery voltage as monitored by the IPC.
Battery Voltage
Scan Tool
Parameter
Data
List
Units Displayed
Typical Data
Value
Operating Conditions: Ignition in RUN, Radio ON
Balance
Data
Value
-50 to +50
Battery Voltage
Data
Volts
0-18 Volts
Chime Type
Outputs
None/Headlamp/Turn Signal/Key in Ignition/Seat Belt/
Park Brake
None
Fade
Data
Value
-50 to +50
Personalization
Inputs
Fuel/Trip/Re/Set/Fuel Econ
Varies
Volume
Data
Percent
0-100%
2004 Hummer H2
2004 ACCESSORIES & EQUIPMENT Instrument Panel, Gauges, and Console - Hummer H2
The scan tool displays 0-18 volts. The voltage measured from the radio or amplifier's ignition positive
voltage circuit to ground.
Brake Assist
The scan tool displays Active or Inactive. This is the state of the brake assist as monitored by the IPC.
Brake Lamp
The scan tool displays On or Off. This is the state of the BRAKE indicator as commanded by the IPC.
Business Trip Avg Speed
The scan tool displays 0.0 to 999.9 mph (0.0 to 999.9 km/h). The DIC calculates the average speed from
the business trip distance and time.
Business Trip Fuel Used
The scan tool displays 0.0 to 9999.9 gallons (0.0 to 9999.9 liters). The DIC calculates the business trip
fuel used based on the class 2 message from the PCM.
Business Trip Mileage
The scan tool displays 0.0 to 999999.9 miles (0.0 to 999999.9 kilometers). The distance traveled is
determined using the 4 kppm vehicle speed signal circuit from the PCM.
Business Trip Percent
The scan tool displays 0 to 100%. The DIC calculates the business trip percent of annual mileage from
the total business mileage travelled and the annual mileage travelled.
Cargo Door Ajar Switch
The scan tool displays Open or Closed. The BCM monitors the signal circuit of the cargo door ajar
switch. An open switch is displayed as Open with the door open.
Cargo Lamp On
The scan tool displays On or Off. This is the state of the cargo lamp as commanded by the IPC.
Cargo Lamp Switch
The scan tool displays On or Off. The scan tool displays On when the cargo lamps are requested from the
switch.
Change Engine Oil
2004 Hummer H2
2004 ACCESSORIES & EQUIPMENT Instrument Panel, Gauges, and Console - Hummer H2
The scan tool displays On or Off. This is the state of the change engine oil indicator as commanded by the
IPC.
Check Coolant Temp
The scan tool displays On or Off. This is the state of the check coolant temperature indicator as
commanded by the IPC.
Check Engine Oil Level
The scan tool displays On or Off. This is the state of the check engine oil level indicator in the message
center as commanded by the IPC.
Check Engine Temp
The scan tool displays On or Off. This is the state of the check engine temperature indicator as
commanded by the IPC.
Chime Type
The scan tool displays None, Headlamp, Turn Signal, Key in Ignition, Seat Belt, or Park Brake. The
selected condition that produces the chime is displayed.
Coolant Level Switch
The scan tool displays OK or Low. The PCM monitors the coolant level switch signal circuit and a closed
switch is displayed as OK.
Cruise Control
The scan tool displays On or Off. The state of the cruise control indicator as commanded by the IPC.
Cumulative Fuel
The scan tool displays gallons (Liters). The DIC receives a class 2 message from the PCM indicating the
cumulative fuel gallons (liters).
Dimming
The scan tool displays Inactive or Active. Inactive is displayed when the PRNDL and the odometer or trip
odometer vacuum florescent display cannot be dimmed from the dimmer switch. Active is displayed
when the PRNDL and the odometer or trip odometer vacuum florescent display can be dimmed from the
dimmer switch in the IPC.
Display Fuel Switch
2004 Hummer H2
2004 ACCESSORIES & EQUIPMENT Instrument Panel, Gauges, and Console - Hummer H2
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст