Hummer H2. Manual — part 184
The year when module was built.
DIAGNOSTIC TROUBLE CODE (DTC) LIST
Diagnostic Trouble Code (DTC) List
DTC B1000
Circuit Description
The internal fault detection is handled inside the control module. No external circuits are involved.
Conditions for Running the DTC
The module runs the program to detect an internal fault when power up is commanded. The only requirements
are voltage and ground. This program runs even if the voltage is out of the valid operating range.
Conditions for Setting the DTC
The module has detected an internal malfunction.
Action Taken When the DTC Sets
The module refuses all additional inputs.
Conditions for Clearing the DTC
z
A current DTC clears when the malfunction is no longer present.
z
A history DTC clears when the module ignition cycle counter reaches the reset threshold, without a repeat
of the malfunction.
Diagnostic Aids
z
This DTC may be stored as a history DTC without affecting the operation of the module. If stored only as
a history DTC and not retrieved as a current DTC, do not replace the module.
DTC
Diagnostic
Procedure
Module
B1000 DTC B1000
Audio Amplifier, BCM, DDM, DSM, FPDM, HVAC, IPC, Radio, SDM,
VCIM
B1004 DTC B1004
VCIM
B1007 DTC B1007
VCIM
B1009 DTC B1009
VCIM
B1397 DTC B1397
BCM
B1440 DTC B1440
BCM
C0550 DTC C0550
EBCM, ESC, TCSCM
2004 Hummer H2
2004 ACCESSORIES & EQUIPMENT Body Control System - Hummer H2
z
If this DTC is retrieved as both a current and history DTC, replace the module.
DTC B1000
DTC B1004
Circuit Description
The internal fault detection is handled inside the control module. No external circuits are involved.
Conditions for Running the DTC
The module microprocessor must be active/awake.
Conditions for Setting the DTC
This DTC indicates the KAM in the module has been reset. It is a normal occurrence when battery positive
voltage or ground is removed from the module, such as a battery disconnect.
Action Taken When the DTC Sets
The microprocessor reverts back to the base programmed critical operating data until new data is learned and
Step
Action
Yes
No
1
Did you perform the Diagnostic System Check for the
system exhibiting the symptom?
Go to
Step 2
Go to Control Module
References for the applicable
Diagnostic System Check
2
1. Install a scan tool.
2. Turn ON the ignition, with the engine OFF.
3. Retrieve DTCs.
Is the DTC retrieved as a current DTC?
Go to
Step 3
Go to Diagnostic Aids
3
Replace the control module setting the DTC as current.
Refer to Control Module References .Did you
complete the replacement?
IMPORTANT:
Perform the programming or setup procedure for the
module if required.
Go to
Step 4
-
4
1. Use the scan tool in order to clear the DTCs.
2. Operate the vehicle within the Conditions for
Running the DTC as specified in the supporting
text.
Does the DTC reset?
Go to
Step 2
System OK
2004 Hummer H2
2004 ACCESSORIES & EQUIPMENT Body Control System - Hummer H2
stored in KAM.
Conditions for Clearing the DTC
z
A current DTC clears when the malfunction is no longer present.
z
A history DTC clears when the module ignition cycle counter reaches the reset threshold, without a repeat
of the malfunction.
Diagnostic Aids
z
This DTC may be stored as a history DTC without affecting the operation of the module. If stored only as
a history DTC and not retrieved as a current DTC, do not replace the module.
z
If this DTC is retrieved as both a current and history DTC, replace the module.
DTC B1004
DTC B1007
Circuit Description
As part of normal data processing, the module performs a data programming check on its writes to the
electrically erasable read only memory (EEPROM). The EEPROM write error detection is handled inside the
Step
Action
Yes
No
1
Did you perform the Diagnostic System Check for the
system exhibiting the symptom?
Go to
Step 2
Go to Control Module
References for the applicable
Diagnostic System Check
2
1. Install a scan tool.
2. Turn ON the ignition, with the engine OFF.
3. Retrieve DTCs.
Is the DTC retrieved as a current DTC?
Go to
Step 3
Go to Diagnostic Aids
3
Replace the control module setting the DTC as current.
Refer to Control Module References .Did you
complete the replacement?
IMPORTANT:
Perform the programming or setup procedure for the
module if required.
Go to
Step 4
-
4
1. Use the scan tool in order to clear the DTCs.
2. Operate the vehicle within the Conditions for
Running the DTC as specified in the supporting
text.
Does the DTC reset?
Go to
Step 2
System OK
2004 Hummer H2
2004 ACCESSORIES & EQUIPMENT Body Control System - Hummer H2
control module. No external circuits are involved.
Conditions for Running the DTC
The module runs the program to detect an EEPROM write error. The only requirements are battery positive
voltage and ground. This program runs even if the battery positive voltage is out of the valid operating range.
Conditions for Setting the DTC
The module writes information to a data block in the EEPROM. The module then reads the data and compares it
to what was sent to the data block. If the data does not match after 3 consecutive attempts, the module sets the
DTC.
Action Taken When the DTC Sets
The module writes to another area of the EEPROM, this becomes the new permanent area to store the data. The
data location is allowed to change until all of the available EEPROM is used. If a B1004 DTC is also set, the
module reverts to base operation values programmed for those blocks of data that have failed. The blocks of
data that have not failed the checksum test are not affected.
Conditions for Clearing the DTC
z
A current DTC clears when the malfunction is no longer present.
z
A history DTC clears when the module ignition cycle counter reaches the reset threshold, without a repeat
of the malfunction.
Diagnostic Aids
z
This DTC may be stored as a history DTC without affecting the operation of the module. If stored only as
a history DTC and not retrieved as a current DTC, do not replace the module.
z
If this DTC is retrieved as both a current and history DTC, replace the module.
DTC B1007
Step
Action
Yes
No
1
Did you perform the Diagnostic System Check for the
system exhibiting the symptom?
Go to
Step 2
Go to Control Module
References for the applicable
Diagnostic System Check
2
1. Install a scan tool.
2. Turn ON the ignition, with the engine OFF.
3. Retrieve DTCs.
Is the DTC retrieved as a current DTC?
Go to
Step 3
Go to Diagnostic Aids
IMPORTANT:
Perform the programming or setup procedure for the
module if required.
2004 Hummer H2
2004 ACCESSORIES & EQUIPMENT Body Control System - Hummer H2
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст