Hummer H2. Manual — part 176
2
2. Unlock the doors using the power
door lock switch or the keyless
entry transmitter.
3. Remove the keys from the ignition.
4. Open the driver's door.
5. Observe the courtesy lamps.
Do the courtesy lamps illuminate?or
Go to Step 3
Go to Courtesy Lamps
Inoperative in Lighting
Systems
3
1. Open the driver's window.
2. Unlock the doors using the power
door lock switch or the keyless
entry transmitter.
3. Remove the keys from the ignition.
4. Open the driver's door.
5. Observe the SECURITY telltale.
Does the SECURITY telltale flash?or
Go to Step 4
Go to Security Indicator
Inoperative
4
1. Lock the vehicle using the power
door lock switches or the keyless
entry transmitter.
2. Observe the SECURITY telltale.
Does the SECURITY telltale change
from flashing to on steady?
Go to Step 5
Go to Power Door Locks
Inoperative (Front Door(s))
or Power Door Locks
Inoperative (Rear Door(s))
in Doors
5
1. Close all of the doors.
2. Observe the SECURITY telltale.
Does the SECURITY telltale turn off in
about 15 seconds?
IMPORTANT:
Ensure that all the doors are
closed. The content theft
deterrent system will not arm
itself without all of the doors
being closed.
Go to Step 6
Go to Courtesy Lamps
Always On in Lighting
Systems
6
1. Reach in and manually unlock the
driver's door.
2. Open the driver's door.
Do all of the alarm mode functions
2004 Hummer H2
2004 ACCESSORIES & EQUIPMENT Theft Deterrent - Hummer H2
CONTENT THEFT DETERRENT (CTD) DOES NOT DISARM WITH KEY LOCK
Content Theft Deterrent (CTD) Does Not Disarm with Key Lock
activate, parking lights flash and horn
pulses?
Go to Step 7
Go to Step 8
7
Disarm the CTD system by inserting the
door key into the driver or the passenger
door lock cylinder and rotate the key to
the unlock position.
Do all of the alarm mode functions stop?
Go to Testing for
Intermittent Conditions
and Poor Connections
in Wiring Systems
Go to Content Theft
Deterrent (CTD) Does Not
Disarm with Key Lock
8
Do any of the alarm functions activate?
Go to Step 9
Go to Courtesy Lamps
Inoperative in Lighting
Systems
9
Do the horns pulse only?
Go to Lights
Inoperative in Content
Theft Deterrent (CTD)
Alarm Mode
Go to Horn Inoperative in
Content Theft Deterrent
(CTD) Alarm Mode
Step
Action
Value(s)
Yes
No
Schematic Reference:Theft Deterrent System Schematics
Connector End View Reference:Theft Deterrent System Connector End Views
DEFINITION: The CTD system does not disarm when the vehicle is unlocked with the key.
1
Did you perform the Theft Deterrent Diagnostic System
Check?
-
Go to
Step 2
Go to Diagnostic
System Check -
Theft Deterrent
2
1. Turn ON the ignition with the engine OFF.
2. With a scan tool, observe the door key switch
parameter in the Body Control Module (BCM)
security data list.
Does the scan tool display INACTIVE?
INACTIVE
Go to
Step 3
Go to Step 11
3
1. Turn OFF the ignition.
2. With a scan tool, observe the door key switch
parameter in the BCM data list.
3. Insert the ignition key into the drivers door lock
cylinder.
4. Turn and hold the door lock cylinder to the
UNLOCK position.
Does the scan tool display ACTIVE?
ACTIVE
Go to
Step 6
Go to Step 4
1. Insert the ignition key into the passenger door
lock cylinder.
2. With a scan tool, observe the door key switch
2004 Hummer H2
2004 ACCESSORIES & EQUIPMENT Theft Deterrent - Hummer H2
4
parameter in the BCM data list.
3. Turn and hold the door lock cylinder to the
UNLOCK position.
Does the scan tool display ACTIVE?
ACTIVE
Go to
Step 9
Go to Step 5
5
1. Connect a 3 amp fused jumper wire between the
signal circuit of the door key switch and ground.
2. With a scan tool, observe the door key switch
parameter in the BCM data list.
Does the scan tool display ACTIVE?
ACTIVE
Go to
Step 8
Go to Step 18
6
1. Insert the ignition key into the passenger door
lock cylinder.
2. With a scan tool, observe the door key switch
parameter in the BCM data list.
3. Turn and hold the door lock cylinder to the
UNLOCK position.
Does the scan tool display ACTIVE?
ACTIVE
System
OK
Go to Step 7
7
1. Disconnect the RH door key switch connector.
2. With a scan tool, observe the Door Key Switch
parameter.
3. Connect a 3 amp fused jumper wire between the
signal circuit of the door key switch and ground.
Does the scan tool display ACTIVE?
ACTIVE
Go to
Step 8
Go to Step 20
8
1. Connect a 3 amp fused jumper wire between the
signal circuit of the door key switch and the
ground circuit at the RH door key switch
connector.
2. With the scan tool, observe the Door Key Switch
parameter.
Does the scan tool display ACTIVE?
ACTIVE
Go to
Step 19
Go to Step 21
9
1. Disconnect the LH door key switch connector.
2. With a scan tool, observe the Door Key Switch
parameter.
3. Connect a 3 amp fused jumper wire between the
signal circuit of the door key switch and ground.
Does the scan tool display the specified ACTIVE?
ACTIVE
Go to
Step 10
Go to Step 15
1. Connect a 3 amp fused jumper wire between the
2004 Hummer H2
2004 ACCESSORIES & EQUIPMENT Theft Deterrent - Hummer H2
10
signal circuit of the door key switch and the
ground circuit at the LH door key switch
connector.
2. With the scan tool, observe the Door Key Switch
parameter.
Does the scan tool display ACTIVE?
ACTIVE
Go to
Step 17
Go to Step 16
11
1. With a scan tool observe the Door Key Switch
parameter.
2. Disconnect the BCM connector containing the
circuits to the door key switch.
Does the scan tool display INACTIVE?
INACTIVE
Go to
Step 12
Go to Step 22
12
1. Reconnect the BCM connector.
2. Disconnect the LH door key switch connector.
3. With a scan tool observe the Door Key Switch
parameter.
Does the scan tool display INACTIVE?
INACTIVE
Go to
Step 17
Go to Step 13
13
1. Disconnect the RH door key switch connector.
2. With a scan tool observe the Door Key Switch
parameter.
Does the scan tool display INACTIVE?
INACTIVE
Go to
Step 19
Go to Step 14
14
Repair the short to ground in the signal circuit of the
door key switch between the BCM and either door
latch.
Did you complete the repair?
-
Go to
Step 23
-
15
Repair the open in the signal circuit of the door key
switch between the LH door latch and C200.
Did you complete the repair?
-
Go to
Step 23
-
16
Repair the open in the ground circuit of the door key
switch between the LH door key switch connector and
G203.
Did you complete the repair?
-
Go to
Step 23
-
17
Replace the LH door latch. Refer to Latch
Replacement - Front Door in Doors.
Did you complete the replacement?
-
Go to
Step 23
-
18
Repair the open in the signal circuit of the door key
switch between the BCM and C200.
Did you complete the repair?
-
Go to
Step 23
Go to Step 22
19
Replace the RH door latch. Refer to Latch
Replacement - Front Door in Doors.
-
Go to
-
2004 Hummer H2
2004 ACCESSORIES & EQUIPMENT Theft Deterrent - Hummer H2
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст