Hummer H2. Manual — part 2437
5
1. Turn OFF the ignition.
2. Disconnect the AT inline 20-way connector,
additional DTCs may set.
3. Install the J 44152 Jumper Harness (20 pins) on
the engine side of the AT inline 20-way
connector.
4. Turn ON the ignition, with the engine OFF.
5. Using the J 35616 GM Terminal Test Kit,
connect a test lamp from terminal E of the J
44152 to ground.
Refer to Automatic Transmission Inline 20-
Way Connector End View .
Does the test lamp illuminate?
-
Go to Step 6
Go to Step 15
6
1. Connect a test lamp between terminal E and
terminal S of the J 44152 .
Refer to Automatic Transmission Inline 20-
Way Connector End View .
2. Use the scan tool in order to command the 3-2
SS valve assembly ON and OFF three times.
Does the test lamp turn ON and OFF with each
command?
-
Go to Step 8
Go to Step 7
7
Is the test lamp always ON?
-
Go to Step 16
Go to Step 17
8
1. Install the J 44152 on the transmission side of
the AT inline 20-way connector.
2. Using the DMM and the J 35616 , measure the
resistance between the terminal E and terminal
S of the J 44152 .
Refer to Automatic Transmission Inline 20-
Way Connector End View .
Does the resistance measure within the specified
range?
20-32
ohm
Go to Step 9
Go to Step 10
9
1. Measure the resistance from terminal S to
ground.
2. Measure the resistance from terminal E to
ground.
250 K
ohm
Go to
Intermittent
Conditions in
2004 Hummer H2
2004 TRANSMISSION Automatic Transmission - 4L60-E/4L65-E Diagnosis (DTC P0218 To DTC P2771) - Hummer H2
Do both readings measure greater than the specified
value?
Engine Controls -
6.0L (LQ4)
Go to Step 11
10
1. Disconnect the AT wiring harness assembly
from the 3-2 SS valve assembly.
2. Measure the resistance of the 3-2 SS valve
assembly.
Does the resistance measure within the specified
range?
20-32
ohm
Go to Step 18
Go to Step 19
11
1. Disconnect the AT wiring harness assembly
from the 3-2 SS valve assembly.
2. Measure the resistance from the component's
terminals to ground.
Do both readings measure greater than the specified
value?
250 K
ohm
Go to Step 18
Go to Step 19
12 Test the Ignition 0 voltage circuit of the 3-2 SS valve
assembly for a short to ground between the fuse block
and the AT inline 20-way connector.Refer to Testing
for Short to Ground and extxref
document="029_body-21" filetype="sgml"
extrefid="i162420">Wiring Repairs in Wiring
Systems.Did you find and correct the condition?
IMPORTANT:
The condition that affects this circuit may exist in
other connecting branches of the circuit. Refer to
Power Distribution Schematics in Wiring Systems
for complete circuit distribution.
-
Go to Step 21
Go to Step 13
13
Test the Ignition 1 voltage circuit of the 3-2 SS valve
assembly for a short to ground between the AT inline
20-way connector and the 3-2 SS valve
assembly.Refer to Testing for Short to Ground in
Wiring Systems.Did you find a short to ground
condition?
IMPORTANT:
The condition that affects this circuit may exist in
other connecting branches of the circuit. Refer to
Power Distribution Schematics in Wiring Systems
for complete circuit distribution.
-
Go to Step 18
Go to Step 14
14
1. Test each solenoid for a short to ground.
2. Replace the faulty solenoid as necessary.
-
-
2004 Hummer H2
2004 TRANSMISSION Automatic Transmission - 4L60-E/4L65-E Diagnosis (DTC P0218 To DTC P2771) - Hummer H2
Did you complete the replacement?
Go to Step 21
15
Test the Ignition 0 voltage circuit of the 3-2 SS valve
assembly for an open.Refer to Testing for
Continuity and extxref document="029_body-21"
filetype="sgml" extrefid="i162420">Wiring Repairs
in Wiring Systems.Did you find and correct the
condition?
IMPORTANT:
The condition that affects this circuit may exist in
other connecting branches of the circuit. Refer to
Power Distribution Schematics in Wiring Systems
for complete circuit distribution.
-
Go to Step 21
-
16
Test the control circuit of the 3-2 SS valve assembly
for a short to ground between the PCM connector C1
and the AT inline 20-way connector.
Refer to Testing for Short to Ground and extxref
document="029_body-21" filetype="sgml"
extrefid="i162420">Wiring Repairs in Wiring
Systems.
Did you find and correct the condition?
-
Go to Step 21
Go to Step 20
17
Test the control circuit of the 3-2 SS valve assembly
for an open or short to voltage between the PCM
connector C1 and the AT inline 20-way connector.
Refer to Circuit Testing and extxref
document="029_body-21" filetype="sgml"
extrefid="i162420"> Wiring Repairs in Wiring
Systems.
Did you find and correct the condition?
-
Go to Step 21
Go to Step 20
18
Replace the AT wiring harness assembly.
Refer to Valve Body and Pressure Switch
Replacement .
Did you complete the replacement?
-
Go to Step 21
-
19
Replace the 3-2 SS valve assembly.
Refer to Valve Body and Pressure Switch
Replacement .
Did you complete the replacement?
-
Go to Step 21
-
20
Replace the PCM.
Refer to Powertrain Control Module (PCM)
Replacement in Engine Controls - 6.0L (LQ4).
Did you complete the replacement?
-
Go to Step 21
-
Perform the following procedure in order to verify the
repair:
1. Select DTC.
2. Select Clear Info.
2004 Hummer H2
2004 TRANSMISSION Automatic Transmission - 4L60-E/4L65-E Diagnosis (DTC P0218 To DTC P2771) - Hummer H2
DTC P0894
21
3. Drive the vehicle in D3 or D4 and perform a 3-
2 downshift. Ensure that the following
conditions are met:
z
The PCM commands the 3-2 SS valve
assembly ON, and the voltage feedback
drops to zero.
z
The PCM commands the 3-2 SS valve
assembly OFF, and the voltage feedback
increases to B+.
z
All conditions are met for 5 seconds.
4. Select Specific DTC.
5. Enter DTC P0785.
Has the test run and passed?
-
Go to Step 22
Go to Step 2
22
With the scan tool, observe the stored information,
capture info, and DTC Info.
Does the scan tool display any DTCs that you have
not diagnosed?
-
Go to Diagnostic
Trouble Code
(DTC) List in
Engine Controls -
6.0L (LQ4)
System OK
2004 Hummer H2
2004 TRANSMISSION Automatic Transmission - 4L60-E/4L65-E Diagnosis (DTC P0218 To DTC P2771) - Hummer H2
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст