Hummer H2. Manual — part 758
SCAN TOOL OUTPUT CONTROLS
Scan Tool Output Controls
module (PCM)
Does the scan tool communicate
with all control modules?
Go to Step 3
Go to Scan Tool Does Not
Communicate with Class 2
Device in Data Link
Communications
3
Select the display DTCs function
on the scan tool for the following
control modules:
z
Electronic brake control
module (EBCM)
z
Powertrain control module
(PCM)
Does the scan tool display any
DTCs?
Go to Step 4
Go to Symptoms - Anti-lock
Brake System
4
Does the scan tool display any
DTCs which begin with a "U"?
Go to Diagnostic Trouble
Code (DTC) List in Data
Link Communications
Go to Step 5
5
Does the scan tool display DTCs
which begin with a "B"?
Go to Diagnostic Trouble
Code (DTC) List in Body
Control System
Go to Step 6
6
Does the scan tool display DTCs
which begin with a "P"?
Go to Diagnostic Trouble
Code (DTC) List in Engine
Electrical
Go to Diagnostic Trouble Code
(DTC) List
Scan Tool Output
Control
Additional Menu
Selection(s)
Description
Automated Bleed
Procedure
-
Used in order to bleed ABS hydraulics. Refer to ABS
Automated Bleed Procedure .
ABS Warning Lamp
-
Commands the ABS indicator ON and OFF.
LF Inlet Valve
Solenoid
Solenoid Test
Commands the solenoid ON and OFF.
LF Outlet Valve
Solenoid
Solenoid Test
Commands the solenoid ON and OFF.
LR Inlet Valve
Solenoid
Solenoid Test
Commands the solenoid ON and OFF.
LR Outlet Valve
Solenoid
Solenoid Test
Commands the solenoid ON and OFF.
RF Inlet Valve
Solenoid
Solenoid Test
Commands the solenoid ON and OFF.
2004 Hummer H2
2004 BRAKES Anti-Lock Brake System - Hummer H2
SCAN TOOL DATA LIST
The EBCM Scan Tool Data Lists contain all the anti-lock brake system related parameters that are available on
the scan tool. The parameters on the list are arranged in alphabetical order. The "Column" data list shows the
location of the parameter on the scan tool displayed menu selections.
Use the EBCM Scan Tool Data Lists as directed by a diagnostic table or in order to supplement the diagnostic
procedures. Begin all the diagnostic procedures with the ABS Diagnostic Starting Point. Use the EBCM Scan
Tool Data Lists only after the following is determined:
z
There is no published DTC procedure nor published symptom procedure for the customer concern.
OR
z
The DTC or symptom diagnostic procedure indicated by the diagnostic system check does not resolve the
customer concern.
The Typical Data Values are obtained from a properly operating vehicle under the conditions specified in the
first row of the Scan Tool Data List table. Comparison of the parameter values from the suspect vehicle with the
Typical Data Values may reveal the source of the customer concern.
EBCM Scan Tool Data List
RF Outlet Valve
Solenoid
Solenoid Test
Commands the solenoid ON and OFF.
RR Inlet Valve
Solenoid
Solenoid Test
Commands the solenoid ON and OFF.
RR Outlet Valve
Solenoid
Solenoid Test
Commands the solenoid ON and OFF.
Scan Tool Parameter
Data List
Units Displayed
Typical Data Value
Ignition is ON, engine OFF, and vehicle is stationary
ABS Active
ABS
Yes/No
No
Brake Fluid Level
ABS
OK/Low
OK
Brake Switch
ABS
Applied/Released
Released
DRP Active
ABS
Yes/No
No
DRP Disabled
ABS
Yes/No
No
Front TCS Isolation Solenoid
TCS
Active/Inactive
Inactive
Front TCS Prime Solenoid
TCS
Active/Inactive
Inactive
Ignition Voltage Signal
ABS
Volts
B+
Left Front Wheel Speed
ABS
km/h or mph
0
Left Rear Wheel Speed
ABS
km/h or mph
0
LF Inlet Valve Solenoid
ABS
Active/Inactive
Inactive
LF Outlet Valve Solenoid
ABS
Active/Inactive
Inactive
Longitudinal Accelerometer
TCS
Volts
0
2004 Hummer H2
2004 BRAKES Anti-Lock Brake System - Hummer H2
SCAN TOOL DATA DEFINITIONS
Data Display/Definitions
The Scan Tool Data Display/Definitions contains a brief description of all the ABS/TCS data parameters. The
menus available depend on the number and type of system on the vehicle and are listed below in alphanumeric
order.
z
ABS DATA
z
TCS DATA
ABS Active
The scan tool displays Yes or No. The scan tool will display Yes when the ABS is active and No during
normal vehicle operation.
Brake Fluid Level
The scan tool will display OK/Low depending on the state of the Master Cylinder Fluid Level Switch.
Brake Switch
The scan tool will display Applied or Released depending on the state of the brake switch.
DRP Active
The scan tool will display Yes/No depending on the state of the DRP.
DRP Disabled
Loose Surface Mode (TC2)
TCS
Disabled/Enabled
Disabled
LR Inlet Valve Solenoid
ABS
Active/Inactive
Inactive
LR Outlet Valve Solenoid
ABS
Active/Inactive
Inactive
Pump Motor Relay Command
ABS
On/Off
Off
Rear TCS Isolation Solenoid
TCS
Active/Inactive
Inactive
Rear TCS Prime Solenoid
TCS
Active/Inactive
Inactive
RF Inlet Valve Solenoid
ABS
Active/Inactive
Inactive
RF Outlet Valve Solenoid
ABS
Active/Inactive
Inactive
Right Front Wheel Speed
ABS
km/h or mph
0
RR Inlet Valve Solenoid
ABS
Active/Inactive
Inactive
RR Outlet Valve Solenoid
ABS
Active/Inactive
Inactive
Right Rear Wheel Speed
ABS
km/h or mph
0
Solenoid Valve Relay Command
ABS
On/Off
On
TCS Active
TCS
Yes/No
No
2004 Hummer H2
2004 BRAKES Anti-Lock Brake System - Hummer H2
The scan tool will display Yes/No depending on the state of the DRP.
Front TCS Isolation Solenoid
The scan tool will display Active/Inactive. This displays the commanded state of the solenoid valve.
Front TCS Prime Solenoid
The scan tool will display Active/Inactive. This displays the commanded of the solenoid valve.
Ignition Voltage
The scan tool displays 0-17 Volts. The scan tool displays the level of ignition voltage at the EBCM.
Left Front Wheel Speed
The scan tool displays 0-255 km/h or (0-158 mph). The scan tool displays the actual speed of the left
front wheel.
Left Rear Wheel Speed
The scan tool displays 0-255 km/h or (0-158 mph). The scan tool displays the actual speed of the left rear
wheel.
LF Inlet Valve Solenoid Inactive
The scan tool will display Active or Inactive. The scan tool displays the commanded state of the LF inlet
solenoid valve.
LF Outlet Valve Solenoid Inactive
The scan tool will display Active or Inactive. The scan tool displays the commanded state of the LF outlet
solenoid valve.
Longitudinal Accelerometer Sensor
The scan tool will display Volts. The scan tool displays the longitudinal accelerometer signal received
from the sensor.
Loose Service Mode
The scan tool displays Disabled/Enabled. The scan tool displays the switch state.
LR Inlet Valve Solenoid Inactive
The scan tool displays Active or Inactive. The scan tool displays the commanded state of the LR inlet
2004 Hummer H2
2004 BRAKES Anti-Lock Brake System - Hummer H2
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст