Toyota Tundra (2019 year). Instruction — part 33
513
7-3. Do-it-yourself maintenance
7
Mai
ntenan
Air conditioning filter
Turn the engine switch off.
Open the glove box.
Remove the tray.
Remove the cover by sliding up
while pulling toward you.
The air conditioning filter must be changed regularly to maintain
air conditioning efficiency.
Removal method
1
2
3
4
514
7-3. Do-it-yourself maintenance
Remove the filter cover.
Pull the filter out of the filter out-
let.
Remove the air conditioning filter
and replace it with a new one.
The “
UP” marks shown on the fil-
ter should be pointing up.
■
Checking interval
Inspect and replace the air conditioning filter according to the maintenance
schedule. In dusty areas or areas with heavy traffic flow, early replacement
may be required. (For scheduled maintenance information, please refer to the
“Scheduled Maintenance Guide” or “Owner’s Manual Supplement”.)
■
If air flow from the vents decreases dramatically
The filter may be clogged. Check the filter and replace if necessary.
5
6
Replacement method
515
7-3. Do-it-yourself maintenance
7
Mai
ntenan
NOTICE
■
When using the air conditioning system
Make sure that a filter is always installed.
Using the air conditioning system without a filter may cause damage to the
system.
516
7-3. Do-it-yourself maintenance
Wireless remote control battery
● Flathead screwdriver
● Small flathead screwdriver
● Lithium battery CR2016
Remove the cover.
To prevent damage to the key,
cover the tip of the screwdriver with
a rag.
To prevent the buttons from being
disassembled, face the button sur-
face downward.
Remove the module.
Open the case cover using a
coin protected with tape, etc.,
and remove the depleted bat-
tery.
Insert a new battery with the “+”
terminal facing up.
: If equipped
Replace the battery with a new one if it is depleted.
You will need the following items:
Replacing the battery
1
2
3
517
7-3. Do-it-yourself maintenance
7
Mai
ntenan
■
Use a CR2016 lithium battery
●
Batteries can be purchased at your Toyota dealer, local electrical appliance
shops or camera stores.
●
Replace only with the same or equivalent type recommended by the manu-
facturer.
●
Dispose of used batteries according to local laws.
■
If the key battery is depleted
The following symptoms may occur:
●
The wireless remote control will not function properly.
●
The operational range will be reduced.
WARNING
■
Removed battery and other parts
Keep away from children. These parts are small and if swallowed by a child,
they can cause choking. Failure to do so could result in death or serious
injury.
■
Certification for the lithium battery
CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN
INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO
THE INSTRUCTIONS
NOTICE
■
For normal operation after replacing the battery
Observe the following precautions to prevent accidents:
●
Always work with dry hands.
Moisture may cause the battery to rust.
●
Do not touch or move any other component inside the remote control.
●
Do not bend either of the battery terminals.
518
7-3. Do-it-yourself maintenance
Checking and replacing fuses
Turn the engine switch off.
Open the fuse box cover.
Engine compartment
Push the tab in and lift the
cover off.
Under the instrument panel
Remove the cover.
Remove the fuse with the pull-
out tool.
Only type A fuse can be removed
using the pullout tool.
If any of the electrical components do not operate, a fuse may
have blown. If this happens, check and replace the fuses as nec-
essary.
1
2
3
519
7-3. Do-it-yourself maintenance
7
Mai
ntenan
Check if the fuse is blown.
Normal fuse
Blown fuse
Type A and B:
Replace the blown fuse with a new fuse of an appropriate amperage rat-
ing. The amperage rating can be found on the fuse box cover.
Type C:
Contact your Toyota dealer.
■
After a fuse is replaced
●
If the lights do not turn on even after the fuse has been replaced, a bulb may
need replacement. (
●
If the replaced fuse blows again, have the vehicle inspected by your Toyota
dealer.
■
If there is an overload in a circuit
The fuses are designed to blow, protecting the wiring harness from damage.
4
1
2
Type A
Type B
Type C
520
7-3. Do-it-yourself maintenance
WARNING
■
To prevent system breakdowns and vehicle fire
Observe the following precautions.
Failure to do so may cause damage to the vehicle, and possibly a fire or
injury.
●
Never use a fuse of a higher amperage rating than that indicated, or use
any other object in place of a fuse.
●
Always use a genuine Toyota fuse or equivalent.
Never replace a fuse with a wire, even as a temporary fix.
●
Do not modify the fuses or fuse boxes.
NOTICE
■
Before replacing fuses
Have the cause of electrical overload determined and repaired by your
Toyota dealer as soon as possible.
521
7-3. Do-it-yourself maintenance
7
Mai
ntenan
Light bulbs
Check the wattage of the light bulb to be replaced. (
■
Front
You may replace the following bulbs by yourself. The difficulty
level of replacement varies depending on the bulb. If neces-
sary bulb replacement seems difficult to perform, contact your
Toyota dealer.
For more information about replacing other light bulbs, contact
your Toyota dealer.
Preparing for light bulb replacement
Bulb locations
Headlights (bulb type)
Front turn signal lights/parking lights (bulb type)
Front side marker lights
Fog lights (bulb type) (if equipped)
1
2
3
4
522
7-3. Do-it-yourself maintenance
■
Rear
Stop/tail and rear side marker lights
Back up lights
Rear turn signal lights
License plate lights
High mounted stoplight and cargo lamps
1
2
3
4
5
523
7-3. Do-it-yourself maintenance
7
Mai
ntenan
■
Headlights (bulb type)
To allow enough working
space, turn the steering
wheel to the opposite side of
the bulb to be replaced.
Remove the screws and
fender liner clip, and remove
the fender liner.
Turn the steering wheel to the
left when replacing the right side
light bulb, and turn the steering
wheel to the right when replac-
ing the left side light bulb.
Open the fender liner and
unplug the connector.
Replacing light bulbs
1
2
524
7-3. Do-it-yourself maintenance
Remove the rubber cover.
Release the bulb retaining
spring.
Remove the bulb.
Set the new light bulb.
To install a new bulb, align tabs
of the bulb with the cutouts of
the mounting hole.
3
4
5
6
525
7-3. Do-it-yourself maintenance
7
Mai
ntenan
Install the bulb retaining
spring.
Install the rubber cover.
When installing the rubber
cover:
Install the connector.
7
8
9
527
7-3. Do-it-yourself maintenance
7
Mai
ntenan
■
Front turn signal/parking lights (bulb type headlights)
Turn the bulb base counter-
clockwise.
Remove the light bulb.
■
Front turn signal lights (LED type headlights)
Turn the bulb base counter-
clockwise.
Remove the light bulb.
1
2
1
2
528
7-3. Do-it-yourself maintenance
■
Front side marker lights
To allow enough working
space, turn the steering
wheel to the opposite side of
the bulb to be replaced.
Remove the screws and
fender liner clip, and remove
the fender liner.
Turn the steering wheel to the
left when replacing the right side
light bulb, and turn the steering
wheel to the right when replac-
ing the left side light bulb.
Open the fender liner and
turn the bulb base counter-
clockwise.
1
2
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст