Toyota Proace EV (2022 year). Manual in english — page 10
189
Detection - Alert
Malfunction
Distraction detection
You are alerted by the flashing of this
Depending on the vehicle’s equipment:
warning lamp in the instrument panel,
The indicator lamp in this button flashes.
WARNING
accompanied by an audible signal.
or
Refer to the General recommendations on
NOTICE
/
The button flashes and a fault
the use of driving and manoeuvring aids.
6
appears.
No warning is transmitted while the direction
Depending on version, the function consists of
Consult any authorized Toyota retailer or Toyota
indicator is active and for approximately
either the "Coffee Break Alert" system alone
authorized repairer, or any reliable repairer.
20 seconds after the direction indicator is
or combined with the "Driver Attention Alert"
switched off.
NOTICE
system.
Detection may be impeded:
WARNING
Activation/Deactivation
- If the markings on the ground are worn
and not clearly contrasted against the road
These systems are in no way designed to
With audio system
keep the driver awake or to prevent the driver
surface.
- If the windscreen is dirty.
from falling asleep at the wheel.
- In certain extreme weather conditions:
It is the driver’s responsibility to stop if feeling
fog, heavy rain, snow, shade, bright sunlight
tired.
or direct exposure to the sun (e.g. low sun,
Take a break in case of feeling tired or at least
leaving a tunnel).
every 2 hours.
Activation/Deactivation
This function is set via the vehicle
► To activate or deactivate the system, press
configuration menu.
this button.
The state of the system is memorised when the
The indicator lamp is on when the system is
ignition is switched off.
activated.
With touch screen
The settings are changed via the vehicle
configuration menu.
190
Coffee Break Alert
Driver Attention Warning
NOTICE
The system triggers an alert as soon as it
Depending on version, the "Coffee Break Alert"
detects that the driver has not taken a
system is combined with the "Driver Attention
In certain driving conditions (poor road
break after two hours of driving at a speed above
Warning" system.
surface or strong winds), the system may give
65 km/h (40 mph).
alerts independent of the driver's level of
This alert is issued via the display of a message
vigilance.
encouraging you to take a break, accompanied
by an audible signal.
WARNING
If the driver does not follow this advice, the alert
is repeated hourly until the vehicle is stopped.
The following situations may interfere with the
The system resets itself if one of the following
operation of the system or prevent it from
conditions is met:
working:
- engine running, the vehicle has been
- lane markings absent, worn, hidden (snow,
stationary for more than 15 minutes,
mud) or multiple (roadworks),
- the ignition has been switched off for a few
- close to the vehicle ahead (lane markings
minutes,
Using a camera placed at the top of the
not detected),
- the driver's seat belt is unfastened and their
windscreen, the system assesses the
- roads that are narrow, winding, etc.
door is opened.
driver's level of vigilance, fatigue or distraction by
identifying variations in trajectory compared to
NOTICE
the lane markings.
This system is particularly suited to fast roads
As soon as the speed of the vehicle drops
(speed higher than 40 mph (65 km/h)).
below 65 km/h (40 mph), the system goes
At a first-level alert, the driver is warned by the
into standby.
“Take care!” message, accompanied by an
The driving time is counted again once the
audible signal.
speed is above 65 km/h (40 mph).
After three first-level alerts, the system triggers
a further alert with the message "Dangerous
driving: take a break", accompanied by a more
pronounced audible signal.
191
The warning is given by a fixed warning lamp
Blind Spot Monitoring
that appears in the door mirror on the side in
System
question:
- immediately, when being overtaken;
WARNING
- after a delay of about one second, when
overtaking a vehicle slowly.
Refer to the General recommendations on
6
the use of driving and manoeuvring aids.
Operation
Sensors fitted in the front and rear bumpers
monitor the blind spots.
The alert is given by an orange warning lamp
coming on in the relevant door mirror, as soon as
a vehicle - car, lorry, bicycle - is detected.
The following conditions must be met for this:
- all vehicles are moving in the same direction
and in adjacent lanes,
- the speed of your vehicle must be between 7
and 87 mph (12 and 140 km/h),
This system includes sensors, placed on the
- you overtake a vehicle with a speed difference
sides of the bumpers, and warns the driver of
of less than 6 mph (10 km/h),
the potentially dangerous presence of another
- a vehicle overtakes you with a speed
vehicle (car, truck, motorcycle) in the blind spot
difference of less than 16 mph (25 km/h),
areas of their vehicle (areas hidden from the
- the traffic is flowing normally,
driver's field of vision).
- overtaking a vehicle over a certain period of
time where the vehicle being overtaken remains
in the blind spot,
- you are driving on a straight or slightly curved
road,
- your vehicle is not towing a trailer, a caravan,
No alert will be given in the following situations:
etc.
- in the presence of non-moving objects (parked
vehicles, safety barriers, street lamps, road
signs, etc.),
192
- with vehicles moving in the opposite direction,
With touch screen
Parking sensors
- driving on a winding road or sharp bends,
The settings are changed via the vehicle
- when overtaking or being overtaken by a very
configuration menu.
WARNING
long vehicle (lorry, bus, etc.) which is both in the
rear blind spot and present in the driver’s front
NOTICE
Refer to the General recommendations on
field of vision,
the use of driving and manoeuvring aids.
- when overtaking quickly,
The system is automatically deactivated when
- in very heavy traffic: vehicles detected in
towing with a towing device approved by
front and behind are confused with a lorry or a
TOYOTA.
stationary object.
Malfunction
Activation/Deactivation
Depending on the vehicle’s equipment:
With audio system
Using sensors located in the bumper, this
In the event of a fault, this or these warning
system signals the proximity of obstacles
lamp(s) flash(es).
(e.g. pedestrian, vehicle, tree, barrier) present in
or
their field of detection.
The warning lamp in this button flashes
and a message appears, accompanied by
Rear parking sensors
an audible signal.
Consult any authorized Toyota retailer or Toyota
The system is switched on by engaging reverse
authorized repairer, or any reliable repairer.
gear, which is confirmed by an audible signal.
► To activate or deactivate the system, press
The system is switched off when disengaging
this button.
reverse gear.
The indicator lamp is on when the system is
activated.
193
Audible assistance
Deactivation/Activation
With button
6
This supplements the audible signal by
displaying bars on the screen that move
The function signals the presence of obstacles
progressively nearer to the vehicle (green: more
present within the sensors’ detection zone.
distant obstacles; yellow: close obstacles; red:
The proximity information is given by an
very close obstacles).
intermittent audible signal, the frequency of
► To deactivate or activate the system, press
When the obstacle is very close, the "Danger"
which increases as the vehicle approaches the
this button.
symbol is displayed on the screen.
obstacle.
The indicator lamp is on when the system is
When the distance between the vehicle and
Front parking sensors
deactivated.
the obstacle becomes less than about thirty
In addition to the rear parking sensors, the front
With audio system or touch screen
centimetres, the audible signal becomes
parking sensors are triggered when an obstacle
The settings are changed via the
continuous.
is detected in front and the speed of the vehicle
vehicle configuration menu.
The sound emitted by the speaker (right or left)
is still below 10 km/h (6 mph).
allows you to identify the side on which the
The front parking sensors are interrupted if the
NOTICE
obstacle is located.
vehicle stops for more than three seconds in
forward gear, if an obstacle is no longer detected
The rear parking sensors system will be
Visual assistance
or when the speed of the vehicle exceeds
deactivated automatically if a trailer or bicycle
10 km/h (6 mph).
carrier is connected to a towing device
installed in accordance with the
NOTICE
manufacturer's recommendations.
The sound emitted by the speaker (front or
rear) locates the obstacle relative to the
Operating limits
vehicle, in front or behind it.
If the boot is heavily loaded, the vehicle may tilt,
affecting distance measurements.
194
Malfunction
WARNING
In the event of a malfunction when
changing into reverse gear, this warning
Check the cleanliness of the camera lens
lamp lights up on the instrument panel,
regularly.
accompanied by the display of a message and
Clean the reversing camera regularly using a
an audible signal (short beep).
soft, dry cloth.
Have it checked by any authorized Toyota
retailer or Toyota authorized repairer, or any
reliable repairer.
Top Rear Vision
The blue lines (1) represent the width of the
vehicle including the mirrors.
VisioPark Light
WARNING
The red line (2) represents a distance of 30 cm
from the rear bumper and the thin blue lines 1 m
Refer to the General recommendations on
WARNING
(A) and 2 m (B) respectively.
the use of driving and manoeuvring aids.
Refer to the General recommendations on
WARNING
the use of driving and manoeuvring aids.
They are represented as lines marked "on the
ground" and do not indicate the position of the
vehicle in relation to tall obstacles (e.g. other
vehicles).
Some distortion of the image is normal.
It is normal to have a part of the number plate
showing at the bottom of the screen.
As soon as reverse gear is engaged with the
engine running, this system displays views of
NOTICE
your vehicle’s close surroundings on the touch
The visual reversing assistance camera is
screen using a camera located at the rear of the
activated automatically when reverse gear is
Opening the tailgate or rear door (depending
vehicle.
engaged.
on equipment) can interfere with the display.
The function may be supplemented by parking
If a side-hinged door is open, allow for the
sensors.
space it occupies.
The image is displayed in the screen.
195
Principle of operation
Activation
Activation is automatic on engaging reverse gear
at a speed lower than 6 mph (10 km/h).
6
Using the rear camera, the vehicle's close
surroundings are recorded during manoeuvres
at low speed.
An image from above your vehicle in its close
You can choose the display mode at any time by
The screen is divided into two parts with a
surroundings is reconstructed (represented
pressing this area.
contextual view and a view from above the
between the brackets) in real time and as the
When the sub-menu is displayed, select one of
vehicle in its close surroundings.
manoeuvre progresses.
the four views:
The parking sensors supplement the information
It facilitates the alignment of your vehicle when
"Standard view".
on the view from above the vehicle.
parking and allows obstacles close to the vehicle
Various contextual views may be displayed:
to be seen. It is automatically deleted if the
"180° view".
- Standard view.
vehicle remains stationary for too long.
- 180° view.
"Zoom view".
- Zoom view.
AUTO mode is activated by default.
"AUTO mode".
In this mode, the system chooses to display the
best view (standard or zoom).
You can change the type of view at any time
during a manoeuvre.
The state of the function is not saved when the
ignition is switched off.
196
AUTO mode
Standard view
NOTICE
The function will be deactivated:
- If a trailer is attached or a bicycle carrier
is fitted on a towing device (vehicle fitted
with a towing device installed in line with the
manufacturer's recommendations).
- Above about 6 mph (10 km/h).
- When the boot is opened.
- Upon changing out of reverse gear (the
image remains displayed for 7 seconds).
- By pressing the white arrow in the upper-
This mode is activated by default.
left corner of the touch screen.
Using sensors in the rear bumper, the automatic
The area behind the vehicle is displayed on the
view changes from the rear view (standard) to
screen.
the view from above (zoom) as an obstacle is
The blue lines 1 represent the width of your
approached at the level of the red line (less than
vehicle, with the mirrors unfolded; their direction
30 cm) during a manoeuvre.
changes depending on the position of the
steering wheel.
The red line 2 represents a distance of 30 cm (0
ft 11") from the rear bumper; the two blue lines 3
and 4 represent 1 m and 2 m (3 ft 3" and 6 ft 6"),
respectively.
This view is available with AUTO mode or in the
view selection menu.
197
Zoom view
180° view
Quick start mode
6
This mode displays, as quickly as possible, the
The camera records the vehicle's surroundings
contextual view (left-hand part) and the overhead
during the manoeuvre in order to create a
view of the vehicle.
view from above the rear of the vehicle in its
A message is displayed advising you to check
near surroundings, allowing the vehicle to be
your vehicle's surroundings before starting the
manoeuvred around obstacles nearby.
manoeuvre.
This view is available with AUTO mode or in the
The 180° view facilitates reversing out of a
view selection menu.
parking bay, making it possible to see the
approach of vehicles, pedestrians and cyclists.
NOTICE
This view is not recommended for carrying out a
complete manoeuvre.
Obstacles may appear further away than they
It consists of 3 areas: left A, centre B and right
actually are in reality.
C.
It is important to check the sides of the
This view is available only from the view
vehicle during the manoeuvre, using the
selection menu.
mirrors.
The rear parking sensors also provide
information on the vehicle's surroundings.
198
Compatibility of fuels
Diesel at low temperature
Refuelling
At temperatures below 0 °C (+32 °F), the
Fuel tank capacity: approximately 69 litres.
formation of paraffins in summer-type Diesel
Reserve level: approximately 6 litres.
fuels could prevent the engine from operating
Diesel fuels conforming to the EN590, EN16734
correctly. In these temperature conditions, use
Low fuel level
and EN16709 standards and containing up to
winter-type Diesel fuel and keep the fuel tank
7%, 10%, 20% and 30% fatty acid methyl ester
When the low fuel level is reached,
more than 50 % full.
respectively. The use of B20 or B30 fuels, even
one of these warning lamps lights
At temperatures below -15 °C (+5 °F) to avoid
occasionally, imposes special maintenance
up on the instrument panel, accompanied by the
problems starting, it is best to park the vehicle
conditions referred to as "Arduous conditions".
display of a message and an audible signal.
under shelter (heated garage).
When it first comes on, about 8 litres of fuel
remain.
Travelling abroad
You must refuel as soon as possible to avoid
Paraffinic Diesel fuel conforming to the EN15940
Certain fuels could damage your vehicle’s
running out of fuel.
standard.
engine.
For more information on Running out of fuel
In certain countries, the use of a particular
WARNING
(Diesel), refer to the corresponding section.
fuel may be required (specific octane rating,
specific trade name, etc.) to ensure correct
NOTICE
The use of any other type of (bio) fuel
operation of the engine.
(vegetable or animal oils, pure or diluted,
For all additional information, consult a dealer.
A small arrow by the warning lamp indicates
domestic fuel, etc.) is strictly prohibited (risk
which side of the vehicle the fuel filler flap is
of damage to the engine and fuel system).
located on.
NOTICE
WARNING
The only Diesel fuel additives authorised for
Stop & Start
use are those that meet the B715000
Never refuel with the engine in STOP mode;
standard.
you must switch off the ignition.
199
Refuelling
► Put the filler cap back in place and close it by
turning to the right.
At least 8 litres of fuel must be added, in order to
► Push the fuel filler flap to close it (your
be registered by the fuel gauge.
vehicle must be unlocked).
Opening the filler cap may create a noise caused
by an inrush of air. This is entirely normal and
results from the sealing of the fuel system.
7
To refuel in complete safety:
► Always switch off the engine.
► Unlock the vehicle using the Smart Entry &
Start.
► With a conventional key, insert the key into
the filler cap, then turn the key to the left.
WARNING
If the vehicle is equipped with a sliding door
on its left-hand side, do not open it while the
fuel filler flap is open (risk of damaging the
fuel filler flap and the sliding door and risk of
injuring the person filling up).
WARNING
► Open the fuel filler flap.
If the fuel filler flap is open and you try to
► Unscrew and remove the filler cap, then
open the left-hand side door, a mechanism
place it on the holder located on the fuel filler
prevents it from being opened.
flap.
The door can be opened half-way, however.
► Insert the nozzle and push it in fully (while
With a mechanical door, close the fuel filler
pushing on the metal valve A).
flap to regain use of the door.
► Fill the tank. Do not continue past the
With an electric door, to be able to use it
third cut-off of the nozzle, as this may cause
correctly, close the fuel filler flap and then
malfunctions.
press an opening control.
200
The vehicle is fitted with a catalytic converter,
NOTICE
which helps to reduce the level of harmful
emissions in the exhaust gases.
Travelling abroad
As Diesel fuel pump nozzles may be different
WARNING
in other countries, the presence of the misfuel
prevention device may make refuelling
If you have put in the wrong fuel for your
impossible.
vehicle, you must have the fuel tank
Before travelling abroad, it is advisable to
drained and filled with the correct fuel
check with any authorized Toyota retailer or
before starting the engine.
Toyota authorized repairer, or any reliable
repairer if the vehicle is suitable for the
When a petrol filler nozzle is inserted into the
Fuel cut-off
distribution equipment of the countries visited.
fuel filler neck of a Diesel vehicle, it comes into
Your vehicle is fitted with a safety system that
contact with the flap. The system remains closed
cuts off the supply of fuel in the event of an
and prevents filling.
impact.
Do not persist but introduce a Diesel type
Charging system
filler nozzle.
(Electric)
Misfuel prevention (Diesel)
(Depending on country of sale.)
NOTICE
400 V electrical system
This mechanical device prevents filling the tank
of a Diesel vehicle with petrol.
It remains possible to use a fuel jerrycan to fill
The electrical traction system, which operates at
Located in the filler neck, the misfuel prevention
the tank.
a voltage of approximately 400 V, is identified by
device appears when the filler cap is removed.
In order to ensure a good flow of fuel, do
orange cables, and its components are marked
not place the nozzle of the fuel can in direct
with this symbol:
contact with the flap of the misfuel prevention
device.
201
WARNING
WARNING
WARNING
An electric vehicle’s power train can become
This label is intended solely for use by
When washing
hot during use and after switching off the
firefighters and maintenance services in the
Before washing the vehicle, always check that
ignition.
event of any work on the vehicle.
the charging flap is closed correctly.
Observe the warning messages shown on
No other person must touch the device shown
Never wash the vehicle while the battery is
7
labels, particularly inside the flap.
on this label.
on charge.
All work on or modifications to the vehicle’s
electrical system (including the traction
WARNING
WARNING
battery, connectors, orange cables and
other components visible from the interior or
In the event of an accident or impact to the
High-pressure washing
exterior) is strictly prohibited - risk of severe
vehicle’s underbody
To avoid damaging the electrical components,
burns or potentially fatal electric shock
In these situations, the electrical circuit or the
it is expressly prohibited to use high-pressure
(short-circuit/electrocution)!
traction battery can be seriously damaged.
washing in the engine compartment or under
In the event of a problem, always contact
Stop as soon as it is safe to do so and switch
the body.
any authorized Toyota retailer or Toyota
off the ignition.
Do not use a pressure greater than 80 bar
authorized repairer, or any reliable repairer.
Contact any authorized Toyota retailer or
when washing the bodywork.
Toyota authorized repairer, or any reliable
repairer.
WARNING
Never allow water or dust to enter the
WARNING
connector or charging nozzle - risk of
In the event of exposure to a fire
electrocution or fire!
Immediately exit and evacuate all passengers
Never connect / disconnect the charging
from the vehicle. Never attempt to fight the
nozzle or cable with wet hands - risk of
fire yourself - risk of electrocution!
electrocution!
You must immediately contact the emergency
services, informing them that the incident
involves an electric vehicle.
202
Traction battery
Charging connectors and
State of charging
Meaning
This battery stores the energy that powers
indicator lamps
indicator lamp
the electric motor and the thermal comfort
Fixed white
Guide lighting
equipment in the passenger compartment. It is
on opening the
discharged during use, and must therefore be
charging flap and
regularly recharged. There is no need to wait
disconnecting the
for the traction battery to fall to its reserve level
charging cable.
before recharging.
Battery life may vary according to the type of
Fixed blue
Deferred charging.
driving, the route, thermal comfort equipment
Flashing green
Charging.
usage and battery component ageing.
Fixed green
Charging complete.
NOTICE
The charging
indicator lamp goes
The traction battery ageing process is
off after about 2
influenced by multiple factors, including
minutes as the
1.
Charging connectors
climate conditions, the distance travelled and
vehicle's functions go
2.
Deferred charging activation button
how often it has been fast-charged.
into standby.
3.
Nozzle locking indicator lamp
The indicator lamp
Fixed red: nozzle positioned correctly and
comes back on
WARNING
locked in the connector.
when the vehicle is
Flashing red: nozzle incorrectly positioned or
unlocked using the
In the event of damage to the traction
locking not possible.
Smart Entry & Start
battery
4.
Charging indicator lamp
or when a door is
It is strictly prohibited to work on the vehicle
opened, to indicate
yourself.
that the battery is
Do not touch liquids coming from the battery,
fully charged.
and in the event of skin contact with these
products, wash abundantly with water and
Fixed red
Malfunction.
contact a doctor as soon as possible.
Contact any authorized Toyota retailer or
Toyota authorized repairer, or any reliable
repairer to have the system checked.
203
travelling abroad, check the compatibility of local
WARNING
electrical systems with the charging cable.
A full range of charging cables is available from
Do not dismantle or modify the charging
your dealer.
connector - risk of electrocution and/or fire!
Contact any authorized Toyota retailer or Toyota
Contact any authorized Toyota retailer or
authorized repairer, or any reliable repairer for
Toyota authorized repairer, or any reliable
7
more information and to obtain suitable charging
repairer.
cables.
Charging cables, sockets
Identification labels on charging plug
and connector
and chargers
Identification labels are attached to the vehicle,
The charging cable supplied with the vehicle
charging cable and charger to inform the user of
(depending on version) is compatible with the
which device they should use.
electrical systems in the country of sale. When
The mean of the each identification label is as follow:
Identification labels
Supply type
Configuration
Type of accessory
Voltage range
AC
TYPE 2
Vehicle connector and
≤ 480 V RMS
vehicle inlet
C
AC
TYPE 2
Plug and socket outlet
≤ 480 V RMS
C
DC
COMBO 2 (FF)
Vehicle connector and
50 V to 500 V
vehicle inlet
K
204
Standard charging, mode 2
is connected correctly and that the electrical
WARNING
system is not faulty.
Domestic socket
If the indicator lamp does not go off, contact any
Specific domestic charging cable (mode 2)
(domestic charging - alternating current (AC))
authorized Toyota retailer or Toyota authorized
You must not damage the cable.
repairer, or any reliable repairer.
In the event of damage, do not use it and
Upon plugging the charging cable into a
contact any authorized Toyota retailer or
domestic socket, all of the indicator lamps come
Toyota authorized repairer, or any reliable
on briefly.
repairer to replace it.
If no indicator lamps come on, check the
Mode 2 with a standard socket: 10 A
domestic socket's circuit-breaker:
maximum charging current.
Control unit (mode 2)
- If the circuit-breaker has tripped, contact a
professional to check that the electrical system
is compatible and/or carry out any necessary
repairs.
- If the circuit-breaker has not tripped, stop
Mode 2 with a Green'Up socket: 16 A
using the charging cable and contact any
maximum charging current.
authorized Toyota retailer or Toyota authorized
To have this type of socket installed, call a
repairer, or any reliable repairer.
professional installer.
Control unit label - Recommendations
Specific domestic charging cable - mode 2
Refer to the handbook before use.
(AC)
POWER
Green: electrical connection established;
charging can begin.
CHARGE
1. Incorrect use of this charging cable may
Flashing green: charging in progress or
result in fire, property damage and serious
temperature pre-conditioning activated.
injury or death by electrocution!
Fixed green: charging complete.
2. Always use a correctly earthed power
FAULT
Identification label C on the charging
socket, protected by a 30 mA residual
Red: fault; charging not permitted or must
connector (vehicle side).
current device.
be stopped immediately. Check that everything
205
3.
Always use an electrical socket protected
Control unit label - State of indicator
by a circuit-breaker appropriate for the
lamps
electrical circuit’s current rating.
State of the
4.
The weight of the control unit must not be
indicator lamp
borne by the electrical socket, plug and
cables.
Off
7
5.
Never use this charging cable if it is
defective or in any way damaged.
6.
Never attempt to repair or open this
On
charging cable. It contains no repairable
parts - replace the charging cable if it is
Flashing
damaged.
7.
Never immerse this charging cable in water.
8.
Never use this charging cable with an
extension cable, a multi-plug socket, a
conversion adaptor or on a damaged
electrical socket.
9.
Do not unplug the plug from the wall as a
means of stopping charging.
10.
Immediately stop charging, by locking and
then unlocking the vehicle using the remote
control key, if the charging cable or wall
socket feel burning hot to the touch.
11.
This charging cable includes components
liable to cause electrical arcing or sparks.
Do not expose to flammable vapours.
12.
Only use this charging cable with TOYOTA
vehicles.
13.
Never plug the cable into the wall socket (or
unplug it) with wet hands.
14.
Do not force the connector if it is locked into
the vehicle.
206
POWER
CHARGE
FAULT
Symbol
Description
Not connected to the power supply or power is not
available from the infrastructure.
The control unit is currently performing a self-test.
(green)
(green)
(red)
Connected only to the infrastructure or to the
infrastructure and to the Electric Vehicle (EV) but
no charging in progress.
(green)
Connected to the power supply and to the Electric
Vehicle (EV).
The EV is on charge or in a temperature pre-
(green)
(green)
conditioning sequence.
Connected to the power supply and to the Electric
Vehicle (EV).
The EV is waiting for charging or the charging of
(green)
(green)
the EV is completed.
Control unit malfunction. No charging allowed.
If an error indicator reappears after a manual reset,
the control unit must be checked by any authorized
(red)
Toyota retailer or Toyota authorized repairer, or any
reliable repairer before the next charge.
The control unit is in diagnostic mode.
(green)
(green)
(red)
207
Manual reset procedure
The control unit can be reset by simultaneously disconnecting the charging connector and the wall socket.
Then, reconnect the wall socket first. For more information, refer to the handbook.
Accelerated charging, mode 3
Charging cable, mode 3 (AC)
Superfast charging, mode 4
Accelerated charging unit (depending on
Public fast charger
7
version)
(superfast charging - direct current (DC))
(accelerated charging - single-phase or three-
phase alternating current (AC))
In mode 3 with an accelerated charging unit
socket: 32 A maximum charging current.
Charging cable, mode 4 (DC)
Identification labels C on the charging
(integrated into the public fast charger)
connector (vehicle side) and on the socket
(charger side).
WARNING
In mode 3 with an accelerated charging unit
Accelerated charging unit
Identification label K on the charging
(Wallbox): 32 A maximum charging current.
Do not disassemble or modify the charging
connector (side vehicle).
unit - risk of electrocution and/or fire!
Only use public fast chargers where the cable
Refer to the charging unit manufacturer's user
length does not exceed 30 metres.
manual for the operating instructions.
208
Always park the vehicle in a place with
Charging the traction
NOTICE
temperatures between -10°C and 30°C
battery (Electric)
(parking in a place with extreme temperatures
Lounge mode
To recharge, connect the vehicle to a domestic
When the vehicle is connected, it is possible
can damage the traction battery).
electricity supply (domestic or accelerated
to switch on the ignition and use certain
Disconnect the cable from the (+) terminal
charging) or to a fast public charger (superfast
functions such as the audio and telematics
of the accessory battery in the engine
charging).
system and the air conditioning system for
compartment.
For a full charge, follow the desired charging
several hours.
Connect a 12 V battery charger to the (+) and
procedure without pausing it, until it ends
(-) terminals of the accessory battery about
automatically. Charging can be either immediate
every 3 months in order to recharge the
WARNING
accessory battery and maintain an operating
or deferred (except fast public charger, mode 4).
You can stop domestic or accelerated charging
voltage.
As a safety measure, the engine will not start
at any time by unlocking the vehicle and
if the charging cable is plugged into the
removing the nozzle. For superfast charging,
connector on the vehicle. A warning is
Precautions
refer to the fast public charger.
displayed on the instrument panel.
Electric vehicles were developed in accordance
For more information on the charging displays
with the guidelines on maximum electromagnetic
on the Instrument panel and the Touch screen,
fields issued by the International Commission
refer to the corresponding section.
NOTICE
on Non-Ionizing Radiation Protection (ICNIRP -
1998 Guidelines).
NOTICE
Cooling the traction battery
The cooling fan in the engine compartment
Wearers of pacemakers or equivalent
It is also possible to monitor the charging
devices
comes on during charging to cool the
progress using the MyToyota application
on-board charger and the traction battery.
The electric vehicles have been
(Available soon).
developed in accordance with the
For more information on Remote functions,
guidelines on the maximum levels for
refer to the corresponding section.
NOTICE
electromagnetic fields issued by the International
Commission on Non-Ionizing Radiation
Vehicle immobilised for 1 to 12 months
Protection (ICNIRP - 1998 Guidelines).
Discharge the traction battery down to 2 or
3 bars on the charge level indicator on the
instrument panel.
Do not connect the charging cable.
209
If the exterior temperature is below:
WARNING
WARNING
- 0°C, charging times may be extended.
- -20°C, charging is still possible, but
If in doubt
(During charging)
charging times may be extended even further
Domestic or accelerated charging: do not
While charging is in progress, unlocking the
(the battery has to be heated first).
remain inside or near the vehicle, or near the
vehicle will cause the charging to stop.
charging cable or charging unit, even for a
If no action is taken on one of the openings
7
short time.
(door or boot) or on the charging nozzle, the
WARNING
Superfast charging: do not use the system
vehicle will lock again after 30 seconds and
yourself and avoid approaching public fast
charging will resume automatically.
After charging
charging points. Leave the area and ask a
Never work under the bonnet:
Check that the charging flap is closed.
third party to recharge the vehicle.
- Some areas remain very hot, even an hour
after charging ends - risk of burns!
- The fan may start at any time - risk of cuts
Connection
For domestic or accelerated charging
or strangulation!
► Before charging, check that the drive selector
is in mode P, otherwise charging is not possible.
WARNING
► Open the charging flap by pressing the
WARNING
push-button, and check that there are no foreign
Before charging
bodies on the charging connector.
Depending on the context:
After charging
Domestic charging, mode 2
► Have a professional check that the
Check that the charging flap is closed.
electrical system to be used complies with
Do not leave the cable connected to the
applicable standards and is compatible with
domestic power socket - risk of short-circuit
the vehicle.
or electrocution in the event of contact with or
► Have a professional electrician install
immersion in water!
a dedicated domestic power socket or
accelerated charging unit (Wallbox)
For superfast charging
compatible with the vehicle.
You should preferably use the charging cable
NOTICE
available as an accessory.
For more information, contact a any
Before charging
authorized Toyota retailer or Toyota
Check that the fast public charging station
authorized repairer, or any reliable repairer.
and its charging cable are compatible with the
vehicle.
Большое спасибо!
Ваше мнение очень важно для нас.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст