Toyota Proace EV (2022 year). Manual in english — page 5
84
Panoramic sunroof
Retractable sliding table
Storage
PROACE VERSO
PROACE VERSO
This is fitted with two manual and independent
blinds, which improve thermal and acoustic
comfort.
Blinds
► Slide back the cover for access to 11 litres of
Opening/Closing
storage space.
WARNING
The storage space can only support a
maximum weight of 3 kg; do not exceed this
The table has a central storage space covered
maximum load in use.
by a lid. When deployed, this device becomes
a table with two table tops on which you can
place objects. The central part has two cup/
Moving forward or backward
can holders and can also be used to hold small
objects (e.g. credit card, pen).
The assembly is mounted on a runner allowing it
► Take one of the blinds by its grip and push it
to be positioned either in row 2 or row 3.
back or pull it forwards to the desired position.
85
► Lift the control (without going beyond the
Unfolding
► Push the control then tip the table assembly
point of resistance) and slide the assembly
downward until it clicks into place.
forwards or backwards.
► Release the control when it is in the desired
WARNING
position.
Before stowing the table tops, check that they
► Check that the table is secured on the runner.
are clear. Before tipping the assembly down,
3
If this is not the case, move the assembly slightly
check that the two table tops have clicked
to the next notch on the runner.
home in the low position and that there is
NOTICE
nothing in the cup holder area (such as a can
or pen).
► Operate the control on the top and pull the
You can move the table in both the open and
table assembly up until it clicks into place.
stowed position. However, to ensure safety, it
► Pull each table top fully up then pivot them on
Cup holders
is advised that you handle the assembly in
each side into the horizontal position.
Two cups or cans and small objects (such as
the stowed position.
a credit card, portable ashtray or pen) can be
Folding
carried in the middle of the unfolded table.
WARNING
► Raise each table top, going beyond the point
of resistance, to the vertical position.
WARNING
For the table to run smoothly, ensure that no
► Push each table top down into its housing
objects are blocking the space used by the
Liquids carried in an open vessel (a cup or
until it clicks into place.
runner on the floor.
mug) could be spilt, presenting a risk. Be
Before manoeuvring the table, check that
careful.
there is nothing on the table.
Never use the table in this position while the
vehicle is being driven.
86
Removal
Changing the direction
Refitting
► Check that there is no object obstructing the
runner and preventing proper locking.
► Raise the control fully to release the
With the table removed, you can turn it 180°.
anchorages and tip the table assembly forward.
► Remove the table assembly through the
NOTICE
► Check that the control is in the upper position
sliding door in row 2.
(locking mechanism armed). If not, lift this control
Remove a seat to make this easier.
fully to arm the mechanism.
WARNING
► Place the front of the table on the runner.
► Taking care not to interfere with the control,
Check that there is nothing in the space
tip the assembly towards the rear until you hear
around the runner on the floor, so that the
it lock into place.
table disengages cleanly.
► Check that the assembly is fully locked into
the runner. If not, slide the assembly gently along
the runner until it meets the next notch.
WARNING
Check that the table is fully locked into the
runner - risk of injury in the event of an
accident or sudden braking.
► Release the control until the guide locks into
the runner.
87
WARNING
WARNING
WARNING
Be careful of passengers' feet when
Incorrect use of the table can cause serious
When the table is deployed, each table top
manoeuvring the assembly.
injury.
can support a maximum of 10 kg. If you
Never use the table in the open or deployed
exceed the maximum weight limit, you risk
position while the vehicle is in motion. In the
damaging part or all of the table.
Storage off the runner
3
event of sudden braking, any object placed on
Never lift the table when it is between
the table can become a projectile.
individual seats; you risk damaging the table
WARNING
Ensure that the table is correctly stowed in
tops.
the low position before setting off.
If removing the table from the vehicle for
Never use the table tops as seats or lean on
storage, ensure that it is placed in a clean
them.
area, in order to avoid introducing any foreign
A label attached to the side of the table
bodies into the mechanisms.
serves as a reminder of this.
The table must be placed outside the vehicle,
on a flat and level surface, resting on the
guide so as not to damage visible parts.
WARNING
Caution, when out of the vehicle, the table
leans to the right or left when placed on a
WARNING
surface.
Never place hot objects such as saucepans
or frying pans on the table - risk of damaging
the surface and starting a fire!
WARNING
Before moving the table or an individual seat
forwards or backwards, make sure that the
seat's backrest is upright and the table is
stowed.
88
Heating and Ventilation
WARNING
Avoid driving for too long with the ventilation
Advice
off or with prolonged operation of interior air
recirculation. Risk of misting and deterioration
NOTICE
of the air quality!
Using the ventilation and air conditioning
WARNING
system
ECO
► To ensure that air is distributed evenly,
When stowing the table tops, never place
keep the external air intake grilles at the base
If the interior temperature is very high after
your hand inside the slide area - risk of
of the windscreen, the nozzles, the vents, the
the vehicle has stood for a long time in the
trapping your fingers! Use the handle
air outlets and the air extractor in the boot
sunshine, air the passenger compartment for
provided.
free from obstructions.
a few moments.
► Do not cover the sunshine sensor located
Put the air flow control at a setting high
on the dashboard; this sensor is used to
enough to quickly change the air in the
regulate the automatic air conditioning
passenger compartment.
system.
► Operate the air conditioning system for at
least 5 to 10 minutes once or twice a month to
NOTICE
keep it in perfect working order.
Condensation created by the air conditioning
► If the system does not produce cold air,
results in a discharge of water underneath the
switch it off and contact any authorized Toyota
vehicle. This is perfectly normal.
retailer or Toyota authorized repairer, or any
reliable repairer.
When towing the maximum load on a steep
gradient in high temperatures, switching off
the air conditioning increases the available
engine power, enhancing the towing capacity.
89
NOTICE
NOTICE
Heating
Servicing the ventilation and air
Stop & Start
conditioning system
The heating and air conditioning systems only
► Ensure that the passenger compartment
operate when the engine is running.
filter is in good condition and have the filter
Temporarily deactivate the Stop & Start
3
elements replaced regularly.
system to maintain a comfortable temperature
We recommend using a composite passenger
in the passenger compartment.
Manual air conditioning
compartment filter. Its specific active additive
For more information on the Stop & Start,
The air conditioning system only operates with
helps protect against polluting gases and bad
refer to the corresponding section.
the engine running.
smells.
► To ensure correct operation of the
NOTICE
air conditioning system, have it checked
according to the recommendations in the
ECO driving mode
Manufacturer's service schedule.
Selecting this mode reduces electrical energy
consumption, but restricts the performance
1. Temperature.
of the heating and air conditioning systems,
2. Air flow.
although it does not deactivate them.
3. Air distribution.
4. Interior air recirculation.
ECO
5. Air conditioning on/off.
Contains R134A fluorinated greenhouse
Air flow
gases
► Turn the thumbwheel 2 to obtain a
Depending on version and country of sale, the
comfortable air flow.
air conditioning system may contain R134A
fluorinated greenhouse gases.
Gas capacity 0.5 kg (+/- 0.025 kg), GWP
index 1430 (CO2 equivalent: 0.715 t).
90
Air conditioning
Dual-zone automatic air
NOTICE
With the engine running, the air conditioning is
conditioning
If you set the air flow control to the minimum
designed to operate effectively in all seasons,
position (off), the temperature in the vehicle
with the windows closed.
will no longer be controlled. A slight air flow
It enables you to:
can still be felt however, resulting from the
- lower the temperature in summer,
forward movement of the vehicle.
- enhance the effectiveness of the demisting
function in winter, above 3°C.
1. Temperature.
Temperature
On/Off
2. Air flow.
► Turn the thumbwheel 1 from "LO" (cold)
► Press button 5 to activate/deactivate the air
3. Air distribution.
to "HI" (hot) to adjust the temperature to your
conditioning system.
4. Recirculation of interior air.
requirements.
When the air conditioning is in operation, to
5. Air conditioning on/off.
cool the air more quickly, you can use interior
6. Automatic comfort mode.
Air distribution
air recirculation for a few moments by pressing
7. Visibility programme.
► Pressing button 3 successively directs the air
button 4. Then restore the intake of exterior air.
8.
“Mono” function or Rear heating and air
flow towards:
conditioning on/off (depending on version).
- windscreen, side windows and footwells,
NOTICE
- footwells,
- central vents, side vents and footwells,
The air conditioning does not operate when
Automatic comfort mode
- windscreen, side windows, central vents, side
the air flow adjustment is set to off.
► Press the "AUTO" button 6 to toggle the
vents and footwells,
mode.
- central and side vents,
The active mode appears in the display screen,
WARNING
- windscreen and side windows (demisting or
as described below:
defrosting).
Provides dynamic, effective air flow.
Switching the system off could result in
discomfort (humidity, misting).
Offers the best compromise between a
comfortable temperature and quiet
operation.
Ensures soft, quiet operation by limiting
air flow.
91
Temperature
NOTICE
NOTICE
The driver and front passenger can each set the
When the engine is cold, the air flow will only
temperature to suit their preferences.
For maximum cooling or heating of the
increase to its optimum level gradually, to
The value shown on the display is a level
passenger compartment, it is possible to
avoid distributing too much cold air.
of comfort, not a temperature in Celsius or
exceed the minimum value 14 or the
In cold weather, it prioritises the distribution of
Fahrenheit.
maximum value 28.
3
warm air to the windscreen, the side windows
► Push button 1 down to decrease the value or
► Push button 1 down until "LO" is
and the footwells only.
up to increase it.
displayed or up until "HI" is displayed.
NOTICE
Manual mode
"Mono" function
It is possible to make a different choice from
A setting of around 21 provides optimum
The comfort setting for the passenger side
that offered by the system by changing a
comfort. Depending on your requirements, a
can be indexed to the driver's comfort setting
setting. The other functions will still be managed
setting between 18 and 24 is normal.
(mono-zone).
automatically.
In addition, we recommend avoiding left/right
As soon as a setting is changed, the "AUTO"
setting differences of more than 3.
symbol disappears.
► Press the corresponding button 8 to activate/
deactivate the function.
Deactivating the system
NOTICE
The indicator lamp in the button comes on when
► Press button 2 "-" until the fan symbol
the function is activated.
On entering the vehicle, if the interior
disappears.
The function is deactivated automatically if a
temperature is significantly colder or warmer
This disables all functions of the dual-zone
passenger uses the temperature control.
than the comfort value setting, there is no
automatic air conditioning system.
need to alter the value displayed in order to
The temperature is no longer regulated. A slight
Rear heating - air
reach the required level of comfort. The
flow of air can still be felt, due to the forward
system compensates automatically and
conditioning
movement of the vehicle.
corrects the temperature difference as quickly
► Press button 2 "+" to switch the system on
as possible.
again.
► Press the corresponding button 8 to activate/
deactivate the function.
92
On/Off
Air flow
NOTICE
► Press button 5 to activate/deactivate the air
► Press the buttons 2 to increase/decrease the
For more information, refer to the Rear
conditioning system.
air flow.
heating - air conditioning section.
When the air conditioning is in operation, to
The air flow symbol (a fan) appears. It is filled in
cool the air more quickly, you can use interior
or emptied gradually, according to the value set.
air recirculation for a few moments by pressing
Visibility programme
button 4. Then restore the intake of exterior air.
► Press button 7 "Visibility" to demist or
Interior air recirculation
defrost the windscreen and side windows more
NOTICE
The intake of exterior air prevents the formation
quickly.
of mist on the windscreen and side windows.
The system automatically manages the air
The air conditioning does not operate when
Recirculating the interior air isolates the
conditioning, air flow and air intake, and provides
the air flow adjustment is set to off.
passenger compartment from outside odours
optimum distribution towards the windscreen and
and fumes and allows the desired passenger
side windows.
compartment temperature to be achieved more
WARNING
► Press button 7 "Visibility" again to stop the
rapidly.
programme.
Switching the system off could result in
► Press this button to activate/deactivate
Or
discomfort (humidity, misting).
the function (confirmed by the
► Press button 6 "AUTO" to return to the
illumination/extinction of the indicator lamp).
automatic comfort programme.
Air distribution
Air conditioning
Front demisting
► Pressing button 3 successively directs the air
With the engine running, the air conditioning is
flow towards:
- defrosting
designed to operate effectively in all seasons,
- windscreen, side windows and footwells,
These markings on the control panel
with the windows closed.
- footwells,
indicate the positioning of the controls for
It enables you to:
- central vents, side vents and footwells,
rapid demisting or defrosting of the windscreen
- lower the temperature in summer,
- windscreen, side windows, central vents, side
and side windows.
- enhance the effectiveness of the demisting
vents and footwells,
function in winter, above 3°C.
- central and side vents,
- windscreen and side windows (demisting or
defrosting).
93
Heating or manual air
Dual-zone automatic air
Rear screen and/or door
conditioning
conditioning
mirror demisting/de-icing
3
► Press this button to demist or defrost
the windscreen and side windows more
► Press this button to switch on/off rear screen
quickly.
and door mirror demisting/de-icing (depending
The system automatically manages the air
on version).
conditioning, air flow and air intake, and provides
The indicator lamp in the button comes on when
optimum distribution towards the windscreen and
the function is activated.
side windows.
Demisting/de-icing switches off automatically to
► To turn it off, press this button
prevent excessive power consumption.
► Set the air flow, temperature and air
again or press "AUTO".
distribution controls to the appropriately marked
ECO
The system restarts with the values in use before
positions.
it was deactivated.
► For air conditioning, press this button;
Switch off demisting/de-icing as soon as you
its indicator lamp comes on.
no longer consider it necessary, as
decreasing power consumption in turn
reduces fuel consumption.
NOTICE
Demisting/de-icing only operates with the
engine running.
94
Rear heating - air
Air flow
Additional heating/
► Turn the dial to increase or decrease
conditioning
ventilation system
the air flow.
Comfort temperature
► Turn the thumbwheel from blue (cold)
to red (hot) to modulate the temperature
to your liking.
This control simultaneously adjusts the
temperature and the location of the air delivery:
- blue: the air is delivered mainly at roof level,
- red: the air is delivered mainly by the vent
Heating
located in row 3 on the right.
This is an additional and separate system which
Activation/Deactivation
heats the passenger compartment and improves
defrosting performance.
This indicator lamp is lit while the system
is programmed or set in operation
remotely via the remote control.
It flashes during the whole duration of the
heating and goes off at the end of the heating
cycle or when stopped using the remote control.
Depending on version, this button is accessible
Ventilation
at the front, from the dual-zone automatic air
This system allows ventilation of the passenger
conditioning control panel.
compartment with exterior air to improve the
► Press this button to activate/deactivate
temperature experienced on entering the vehicle
the operation of the rear controls.
in summer.
If your vehicle is fitted with a rear air conditioning
unit located in the roof, this system distributes
conditioned and heated air via a distribution rail
and individual outlets.
95
Programming
With TOYOTA Pro Touch with
NOTICE
navigation system
With a TOYOTA Pro Touch with navigation
system, use the remote control to start/stop the
Using these two clocks and depending on the
In the Applications > Vehicle
additional heating.
season you can, for example, select one or
apps menu:
With a Bluetooth® audio system or a TOYOTA
the other start time.
► Select AIR CON programming.
Pro Touch, use the remote control to start/stop
A message on the screen confirms your
3
the additional heating and/or adjust the pre-
choice.
► Press the Status tab to activate/deactivate
heating times.
the system.
► Press the Settings tab to select Heating
With TOYOTA Pro Touch
With Bluetooth® audio system
mode to heat the engine and passenger
Press Connect-App to display the main
compartment or Ventilation mode to ventilate
page.
the passenger compartment.
Then press "Programmable heating/
► Then programme/save the activation time for
► Press the MENU button to access the
ventilation".
each selection.
main menu.
► Select the "Status" tab to activate/deactivate
► Press OK to confirm.
► Select "Pre-heat. / Pre-ventil.".
the system.
► Select "Activation" and, if necessary, for
► Select the "Other settings" tab to choose
NOTICE
programming, “Parameters".
the "Heating" mode, to heat the engine and
► Select "Heating" to heat the engine and
passenger compartment, or "Ventilation" to
You must allow at least 60 minutes between
passenger compartment or "Ventilation" to
ventilate the passenger compartment.
programming operations.
ventilate the passenger compartment.
► Then set/save the time at which the
preheating temperature will be reached for each
selection.
NOTICE
Press this button to save.
Depending on the outside temperature, a
► Select:
certain amount of pre-conditioning time is
• the first clock to set/save the time at which
necessary in order to reach the programmed
the pre-heating temperature will be reached,
temperature by the stored activation time.
• the second clock to set/save a second time
This pre-conditioning time lasts up to 45 min.
at which the pre-heating temperature will be
reached,
96
Long range remote control
NOTICE
ECO
This enables you to switch the heating in
the passenger compartment on or off from a
The indicator lamp in the remote control
Do not throw remote control batteries away,
distance.
flashes for about 2 seconds if the vehicle has
as they contain metals that are harmful to the
The remote control has a range of about 1 km
not received the signal, in which case
environment. Take them to an approved
(0.6 miles) in open country.
you should move to a different location and
disposal point.
repeat the command.
NOTICE
Changing the battery
The indicator lamp in the remote control will
If the system is switched on using the
change to orange if the battery charge is low.
long-range remote control, the maximum
If the indicator lamp is not on, the battery is
heating duration is around 45 min.
discharged.
NOTICE
The ventilation is activated provided that the
battery is sufficiently charged.
The heating is activated provided that:
On
- the battery charge and the fuel level are
► Pressing and holding this button starts
sufficient,
the heating immediately (confirmed by the
- the engine has been started since the
green indicator lamp coming on briefly).
previous heating cycle,
- 60 minutes have elapsed between two
Off
heating requests.
► Pressing and holding this button stops
► Use a coin to unscrew the cap and replace
the heating immediately (confirmed by the
the battery.
red indicator lamp coming on briefly).
WARNING
Programmable heating is supplied by the
vehicle fuel tank. Before use, make sure that
you have sufficient fuel. If the fuel tank is on
97
reserve, you are strongly recommended not
Independent additional
WARNING
to programme the heating.
heating
Do not park the vehicle on a flammable
Depending on the country of sale, this is an
surface (for example: dry grass, fallen leaves,
additional and independent system which heats
paper, etc.) - risk of fire!
The additional heating must always be
the hot water circuit of the Diesel engine to
3
switched off while refuelling to avoid any risk
improve comfort and to raise the temperature
NOTICE
of fire or explosion.
of the cold engine. It improves demisting and
defrosting performance. With the engine idling
Have the additional heating checked at least
or the vehicle stationary, it is normal to notice a
once a year, at the beginning of winter.
WARNING
high-pitched whistling and some emissions of
For maintenance and repairs, you must only
smoke or odour.
To avoid the risk of poisoning or asphyxia, the
contact any authorized Toyota retailer or
The temperature near the heating system must
programmable heating must not be used,
Toyota authorized repairer, or any reliable
not exceed 120°C. A higher temperature (e.g. in
even for short periods, in a closed
repairer.
a paint oven) could damage the components of
environment such as a garage or workshop
electronic circuits.
which is not equipped with an exhaust gas
The additional heating is supplied by the
extraction system.
vehicle's fuel tank. Make sure that the low fuel
Do not park the vehicle on a flammable
warning lamp is not on.
surface (dry grass, dead leaves, paper, etc.)
- Risk of fire!
NOTICE
To avoid the risks of poisoning or suffocation,
WARNING
the additional heating must not be used, even
for short periods, in a closed environment
Glazed surfaces such as the rear screen or
such as a garage or workshop which is not
windscreen can become very hot in places.
equipped with an exhaust gas extraction
Never put objects on these surfaces; never
system.
touch these surfaces - Risk of burns!
98
A/C preconditioning
Select Temperature conditioning.
Operating conditions
- The function is only activated when the
(Electric)
► Press + to add a programme.
ignition is switched off and the vehicle
This function allows you to programme the
► Select the time of entry into the vehicle and
locked.
temperature in the passenger compartment to
the desired days. Press OK.
- When the vehicle is not connected, the
reach a pre-defined, non-modifiable temperature
► Press ON to activate this programme.
function is only activated if the battery charge
(approx. 21°C) before you enter the vehicle, on
The temperature pre-conditioning sequence
level is greater than 50%.
the days and at the times of your choice.
begins approximately 45 minutes before the
- When the vehicle is not connected and a
This function is available when the vehicle is
programmed time when the vehicle is connected
recurring programme is active (e.g. from Monday
connected or not connected.
(20 minutes when it is not connected) and is
to Friday), if two temperature pre-conditioning
maintained for 10 minutes after.
sequences are run without the vehicle being
Programming
used, the programme will be deactivated.
NOTICE
With Bluetooth® audio system
Temperature pre-conditioning is not available
You can set multiple programmes.
with the Bluetooth® audio system.
Each one is saved in the system.
To optimise the driving range, we recommend
With TOYOTA Pro Touch or TOYOTA Pro
starting a programme while the vehicle is
Touch with navigation system
connected.
Programming can be carried out from a
smartphone using the MyToyota
application (Available soon).
NOTICE
For more information on the Remotely-operable
functions, refer to the corresponding section.
The fan noise that occurs during temperature
pre-conditioning is perfectly normal.
With TOYOTA Pro Touch with navigation
system
In the Applications menu:
Press "Car Apps" to display the applications
home page.
99
Courtesy lamp(s)
Front: comes on when one of the front or
rear doors is opened (sliding side door
and depending on equipment, left-hand
side-hinged door or tailgate).
Rear or row 2 and row 3: comes on when one of
3
the rear doors is opened (sliding side door and
depending on equipment, left-hand side-hinged
door or tailgate).
Always lit, ignition on.
Always off.
Front
Rear
Automatic switching on/off
The front courtesy lamp comes on when the key
is removed from the ignition switch.
All courtesy lamps come on when the vehicle is
unlocked, when one of the corresponding doors
is opened and when locating the vehicle using
the remote control.
They fade to off after the ignition is switched on
and when the vehicle is locked.
WARNING
Take care not to allow objects to come into
contact with the courtesy lamp.
100
Individual reading lamp
If fitted to the vehicle, these are switched
on and off by means of a manual switch.
With the ignition on, operate the corresponding
switch.
WARNING
Take care not to put anything in contact with
the courtesy lamp.
101
Lighting control lever
NOTICE
Operation of the selected lighting is confirmed
Main lighting
by the illumination of the corresponding
indicator lamp.
► Rotate the ring forwards/backwards to turn
it on/off.
4
Without AUTO lighting
When the lighting is switched off automatically
(with AUTO model), the foglamp and the dipped
beam headlamps will remain on.
Front foglamps/Rear foglamps
They operate with the sidelamps, dipped
Lamps off (ignition off)/
or main beam headlamps on.
Daytime running lamps (engine running)
Automatic illumination of lamps/daytime
With AUTO lighting
running lamps
Sidelamps only
Dipped or main beam headlamps
► Rotate the ring forwards:
• once to switch on the front foglamps,
Headlamp dipping
• a second time to switch on the rear
foglamps.
Foglamps
► Turn in the opposite direction to switch off.
If the lighting is switched off automatically (with
Rear foglamp
AUTO model) or the dipped beam headlamps
It only works if the sidelamps are on.
are switched off manually, the foglamps and
► Pull the lever to switch between dipped and
sidelamps remain on.
main beam headlamps.
► Rotate the ring backwards to switch the
In lamps off and sidelamps modes, pull the stalk
foglamps off; the sidelamps will then switch off.
to switch the main beam headlamps on directly
("headlamp flash").
102
Direction indicators
WARNING
NOTICE
Switching on the foglamps is prohibited in
Switching off of the lamps when the
clear weather or in rain, both day and night. In
ignition is switched off
these situations, the power of their beams
When the ignition is switched off, all of the
may dazzle other drivers. They must only be
lamps turn off immediately, except for dipped
used in fog or falling snow (rules may vary
beam headlamps if automatic guide-me-home
depending on country).
lighting is activated.
Do not forget to switch off the foglamps when
they are no longer necessary.
NOTICE
► Left or right: lower or raise the lighting control
In some weather conditions (e.g. low
lever, beyond the point of resistance.
NOTICE
temperature or humidity), misting on the
Switching on the lamps after switching off
internal surface of the glass of the headlamps
NOTICE
the ignition
and rear lamps is normal, and will disappear
If you forget to cancel the direction indicators
To reactivate the lighting control, rotate the
after the lamps have been on for a few
for more than 20 seconds, the volume of the
ring to the "0" position - lamps off, then to the
minutes.
audible signal will increase if the speed is
desired position.
above 50 mph (80 km/h).
If the driver's door is opened, a temporary
NOTICE
audible signal warns the driver that the lamps
are on.
Three flashes
Travelling abroad
They will go off automatically after a period
If planning to use your vehicle in a country
► Press briefly upwards or downwards, without
of time that depends on the level of charge in
that drives on the other side of the road, the
going beyond the point of resistance; the
the battery (entering energy economy mode).
dipped beam headlamps must be adjusted to
direction indicators will flash 3 times.
avoid dazzling oncoming drivers.
Contact any authorized Toyota retailer or
Toyota authorized repairer, or any reliable
repairer.
103
Daytime running lamps/
Malfunction
Guide-me-home and
In the event of a malfunction of the rain/
Sidelamps
welcome lighting
sunshine sensor, the vehicle’s lamps
come on and this warning lamp is displayed on
Guide-me-home lighting
the instrument panel, accompanied by an
audible signal and/or the display of a message.
Manual
4
Have it checked by any authorized Toyota
retailer or Toyota authorized repairer, or any
reliable repairer.
WARNING
Do not cover the rain/sunshine sensor located
at the top centre of the windscreen behind the
interior rear view mirror; the associated
If the vehicle is so equipped, they come on
Switching on/off
functions would no longer be controlled.
automatically when the engine is started,
► With the ignition off, "flash" the headlamps
when the lighting control stalk is in position "0"
using the lighting control lever to switch the
or "AUTO".
NOTICE
function on or off.
Manual guide-me-home lighting goes off
Automatic headlamp
In fog or snow, the rain/sunshine sensor may
automatically at the end of a given period of
detect sufficient light. For this reason, the
time.
illumination
lighting will not come on automatically.
When a low level of ambient light is detected
Automatic
by a sunshine sensor, the number plate
With the "Automatic illumination of lamps"
lamps, sidelamps and dipped beam headlamps
NOTICE
function activated (lighting control stalk in the
are switched on automatically, without any action
"AUTO" position) and when the light is poor, the
The inner surface of the windscreen may
on the part of the driver. They can also come
dipped beam headlamps come on automatically
become misted up and affect the proper
on if rain is detected, at the same time as the
when the ignition is switched off.
operation of the rain/sunshine sensor.
automatic rain sensitive wipers.
In humid and cold weather, demist the
With audio system or touch screen
As soon as the brightness returns to a sufficient
windscreen regularly.
The activation, deactivation and
level or after the windscreen wipers are switched
off, the lamps are switched off automatically.
duration of guide-me-home lighting
are set in the vehicle configuration menu.
104
Exterior welcome lighting
Automatic headlamp
NOTICE
The remote operation of the lighting makes your
dipping
approach to the vehicle easier in poor light. It
The system will be operational as soon as
is activated when the lighting control is in the
When the ring is in the "AUTO” position, this
you exceed 25 km/h (16 mph).
"AUTO" position and the level of light detected
system automatically switches between dipped
If the speed drops below 15 km/h (9 mph), the
by the sunshine sensor is low.
and main beam headlamps according to the
system no longer operates.
lighting and traffic conditions, using a camera
Switching on
located at the top of the windscreen.
Activation/Deactivation
Press this button on the remote control or
on one of the front door handles with the
With audio system
"Smart Entry & Start" system.
The dipped beam headlamps and sidelamps
come on; your vehicle is also unlocked.
Switching off
The exterior welcome lighting switches off
automatically after a set time, when the ignition
is switched on or on locking the vehicle.
Programming
► To activate or deactivate the system, press
With audio system or touch screen
WARNING
this button.
The indicator lamp in the button is on when the
The activation, deactivation and
This system is a driving aid.
function is activated.
duration of the welcome lighting
The driver remains responsible for the
can be set via the vehicle configuration menu.
vehicle's lighting, its correct use for the
With touch screen
prevailing conditions of light, visibility and
The settings are adjusted via the vehicle
traffic, and for observation of driving and
configuration menu.
vehicle regulations.
► Then put the lighting control stalk ring in the
"AUTO" or "Dipped/main beam position".
Большое спасибо!
Ваше мнение очень важно для нас.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст