Toyota Corolla Hybrid (2020 year). Owner's manual — part 28
438
7-3. Do-it-yourself maintenance
6
and
5
with the directions
reversed.
8
Install the light assembly and
then install the 2 screws.
Align the guide
and pin
on
the light assembly with the mount-
ing when installing it.
9
Install the cover.
■
Back-up lights
1
Open the trunk lid, remove
the clips, and pull back the
cover.
2
Turn the bulb base counter-
clockwise and remove it.
3
Remove the light bulb.
4
When installing, reverse the
steps listed.
WARNING
■
Replacing light bulbs
●
Turn off the lights. Do not
attempt to replace the bulb
immediately after turning off the
lights. The bulbs become very
hot and may cause burns.
●
Do not touch the glass portion
of the light bulb with bare
hands. When it is unavoidable
to hold the glass portion, use
and hold with a clean dry cloth
to avoid getting moisture and
oils on the bulb. Also, if the bulb
is scratched or dropped, it may
blow out or crack.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
439
7-3. Do-it-yourself maintenance
7
Maintena
nce
a
nd ca
re
WARNING
●
Fully install light bulbs and any
parts used to secure them. Fail-
ure to do so may result in heat
damage, fire, or water entering
the light unit. This may damage
the lights or cause condensa-
tion to build up on the lens.
■
To prevent damage or fire
Make sure bulbs are fully seated
and locked.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
440
7-3. Do-it-yourself maintenance
-------------------------------------------------------------------------------------------------------------------------------------------------------------
441
8
8
Whe
n tr
ouble
ar
ises
When trouble arises
.
8-1. Essential information
Emergency flashers .
If your vehicle has to be
stopped in an emergency
. . . . . . . . ..
If the vehicle is trapped in
rising water. . . .
8-2. Steps to take in an emer-
gency
If your vehicle needs to be
towed. . . . . . .
If you think something is
wrong . . . . . .
If a warning light turns on or
a warning buzzer sounds
. . . . . . . . ..
If a warning message is dis-
played. . . . . .
If you have a flat tire (vehi-
cles without spare tire)
. . . . . . . . ..
If you have a flat tire (vehi-
cles with a spare tire)
. . . . . . . . ..
If the hybrid system will not
start . . . . . . ...
If you lose your keys ...
If the fuel filler door cannot
be opened . . . . .
If the electronic key does
not operate properly ..
If the 12-volt battery is dis-
charged . . . . . .
If your vehicle overheats
. . . . . . . . ..
If the vehicle becomes stuck
. . . . . . . . ..
-------------------------------------------------------------------------------------------------------------------------------------------------------------
442
8-1. Essential information
8-1.Essential information
Press the switch.
All the turn signal lights will flash.
To turn them off, press the switch
once again.
■
Emergency flashers
●
If the emergency flashers are
used for a long time while the
hybrid system is not operating
(while the “READY” indicator is
not illuminated), the 12-volt bat-
tery may discharge.
●
If any of the SRS airbags deploy
(inflate) or in the event of a strong
rear impact, the emergency flash-
ers will turn on automatically.
The emergency flashers will turn
off automatically after operating
for approximately 20 minutes. To
manually turn the emergency
flashers off, press the switch
twice.
(The emergency flashers may not
turn on automatically depending
on the force of the impact and
conditions of the collision.)
Emergency flashers
The emergency flashers are
used to warn other drivers
when the vehicle has to be
stopped on the road due to
a breakdown, etc.
Operating instructions
-------------------------------------------------------------------------------------------------------------------------------------------------------------
443
8-1. Essential information
8
Whe
n tr
ouble
ar
ises
1
Steadily step on the brake
pedal with both feet and
firmly depress it.
Do not pump the brake pedal
repeatedly as this will increase the
effort required to slow the vehicle.
2
Shift the shift lever to N.
If the shift lever is shifted to N
3
After slowing down, stop the
vehicle in a safe place by the
road.
4
Stop the hybrid system.
If the shift lever cannot be
shifted to N
3
Keep depressing the brake
pedal with both feet to reduce
vehicle speed as much as
possible.
4
To stop the hybrid system,
press and hold the power
switch for 2 consecutive sec-
onds or more, or press it
briefly 3 times or more in suc-
cession.
5
Stop the vehicle in a safe
place by the road.
If your vehicle has to
be stopped in an emer-
gency
Only in an emergency, such
as if it becomes impossible
to stop the vehicle in the
normal way, stop the vehicle
using the following proce-
dure:
Stopping the vehicle
WARNING
■
If the hybrid system has to be
turned off while driving
Power assist for the steering
wheel will be lost, making the
steering wheel heavier to turn.
Decelerate as much as possible
before turning off the hybrid sys-
tem.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
444
8-1. Essential information
Remove the seat belt first.
If the door can be opened,
open the door and exit the
vehicle.
If the door can not be opened,
open the window using the
power window switch and exit
the vehicle through the win-
dow.
If the window can not be
opened using the power win-
dow switch, remain calm, wait
until the water level inside the
vehicle rises to the point that
the water pressure inside of
the vehicle equals the water
pressure outside of the vehi-
cle, and then open the door
and exit the vehicle.
If the vehicle is
trapped in rising water
In the event the vehicle is
submerged in water, remain
calm and perform the fol-
lowing.
WARNING
■
Using an emergency hammer
*
for emergency escape
The front side windows and rear
side windows, as well as the rear
window can be shattered with an
emergency hammer
*
used for
emergency escape. However, an
emergency hammer
*
can not
shatter the windshield as it is lam-
inated glass.
*
: Contact your Toyota dealer or
aftermarket accessory manu-
facturer for further information
about an emergency hammer.
■
Escaping the vehicle from the
window
There are cases where escaping
the vehicle from the window is not
possible due to seating position,
passenger body type, etc.
When using an emergency ham-
mer, consider your seat location
and the size of the window open-
ing to ensure that the opening is
accessible and large enough to
escape.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
445
8-2. Steps to take in an emergency
8
Whe
n tr
ouble
ar
ises
8-2.Steps to take in an emergency
If your vehicle needs
to be towed
If towing is necessary, we
recommend having your
vehicle towed by your Toy-
ota dealer or commercial
towing service, using a
wheel-lift type truck or flat-
bed truck.
Use a safety chain system
for all towing, and abide by
all state/provincial and local
laws.
WARNING
Observe the following precau-
tions.
Failure to do so may result in
death or serious injury.
■
When towing the vehicle
Be sure to transport the vehicle
with the front wheels raised or
with all four wheels raised off the
ground. If the vehicle is towed
with the front wheels contacting
the ground, the drivetrain and
related parts may be damaged or
electricity generated by the opera-
tion of the motor may cause a fire
to occur depending on the nature
of the damage or malfunction.
■
While towing
●
When towing using cables or
chains, avoid sudden starts, etc.
which place excessive stress on
the towing eyelets, cables or
chains. The towing eyelets,
cables or chains may become
damaged, broken debris may hit
people, and cause serious dam-
age.
●
Do not turn the power switch off.
There is a possibility that the
steering wheel is locked and
cannot be operated.
■
Installing towing eyelets to
the vehicle
Make sure that towing eyelets are
installed securely.
If not securely installed, towing
eyelets may come loose during
towing.
NOTICE
■
To prevent damage to the
vehicle when towing using a
wheel-lift type truck
●
Do not tow the vehicle from the
rear when the power switch is
off. The steering lock mecha-
nism is not strong enough to
hold the front wheels straight.
●
When raising the vehicle,
ensure adequate ground clear-
ance for towing at the opposite
end of the raised vehicle. With-
out adequate clearance, the
vehicle could be damaged while
being towed.
■
To prevent damage to the
vehicle when towing with a
sling-type truck
Do not tow with a sling-type truck,
either from the front or rear.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
446
8-2. Steps to take in an emergency
The following may indicate a
problem with your transmission.
Contact your Toyota dealer or
commercial towing service
before towing.
The hybrid system warning
message is shown on the
multi-information display and
the vehicle does not move.
The vehicle makes an abnor-
mal sound.
Do not tow with a sling-type
truck to prevent body damage.
From the front
Release the parking brake.
From the rear
Use a towing dolly under the
front wheels.
If your vehicle is transported by
a flatbed truck, it should be tied
down at the locations shown in
the illustration.
NOTICE
■
To prevent damage to the
vehicle during emergency
towing
Do not secure cables or chains to
the suspension components.
Situations when it is nec-
essary to contact dealers
before towing
Towing with a sling-type
truck
Towing with a wheel-lift
type truck
Using a flatbed truck
-------------------------------------------------------------------------------------------------------------------------------------------------------------
447
8-2. Steps to take in an emergency
8
Whe
n tr
ouble
ar
ises
If you use chains or cables to tie
down your vehicle, the angles
shaded in black must be 45°.
Do not overly tighten the tie
downs or the vehicle may be
damaged.
If a tow truck is not available in
an emergency, your vehicle may
be temporarily towed using
cables or chains secured to the
emergency towing eyelets. This
should only be attempted on
hard surfaced roads for a short
distance at under 18 mph (30
km/h).
A driver must be in the vehicle to
steer and operate the brakes.
The vehicle’s wheels, drive train,
axles, steering and brakes must
be in good condition.
1
Take out the towing eyelet.
(P.464, 474)
2
Remove the eyelet cover
using a flathead screwdriver.
To protect the bodywork, place a
rag between the screwdriver and
the vehicle body as shown in the
illustration.
3
Insert the towing eyelet into
the hole and tighten partially
by hand.
Emergency towing
Emergency towing proce-
dure
-------------------------------------------------------------------------------------------------------------------------------------------------------------
448
8-2. Steps to take in an emergency
4
Tighten down the towing eye-
let securely using a wheel nut
wrench or hard metal bar.
5
Securely attach cables or
chains to the towing eyelet.
Take care not to damage the vehi-
cle body.
6
Enter the vehicle being towed
and start the hybrid system.
If the hybrid system does not start,
turn the power switch to ON.
7
Shift the shift lever to N and
release the parking brake.
When the shift lever cannot
be shifted: P.150
■
While towing
If the hybrid system is off, the power
assist for the brakes and steering
will not function, making steering
and braking more difficult.
■
Wheel nut wrench (vehicles
with a spare tire)
Wheel nut wrench is installed in
trunk. (P.474)
Fluid leaks under the vehicle.
(Water dripping from the air
conditioning after use is nor-
mal.)
Flat-looking tires or uneven
tire wear
Engine coolant temperature
gauge needle continually
points higher than normal.
Changes in exhaust sound
Excessive tire squeal when
cornering
Strange noises related to the
suspension system
Pinging or other noises
related to the hybrid system
Engine missing, stumbling or
running roughly
Appreciable loss of power
Vehicle pulls heavily to one
If you think something
is wrong
If you notice any of the fol-
lowing symptoms, your
vehicle probably needs
adjustment or repair. Con-
tact your Toyota dealer as
soon as possible.
Visible symptoms
Audible symptoms
Operational symptoms
-------------------------------------------------------------------------------------------------------------------------------------------------------------
449
8-2. Steps to take in an emergency
8
Whe
n tr
ouble
ar
ises
side when braking
Vehicle pulls heavily to one
side when driving on a level
road
Loss of brake effectiveness,
spongy feeling, pedal almost
touches the floor
-------------------------------------------------------------------------------------------------------------------------------------------------------------
450
8-2. Steps to take in an emergency
■
Brake system warning light (warning buzzer)
■
Brake system warning light
■
High coolant temperature warning light
*
(warning buzzer)
*
: This light illuminates on the multi-information display.
If a warning light turns on or a warning buzzer
sounds
Calmly perform the following actions if any of the warning
lights comes on or flashes. If a light comes on or flashes, but
then goes off, this does not necessarily indicate a malfunction
in the system. However, if this continues to occur, have the
vehicle inspected by your Toyota dealer.
Actions to the warning lights or warning buzzers
Warning light
Details/Actions
(U.S.A.)
or
(Red)
(Canada)
Indicates that:
The brake fluid level is low; or
The brake system is malfunctioning
Immediately stop the vehicle in a safe place and con-
tact your Toyota dealer. Continuing to drive the vehi-
cle may be dangerous.
Warning light
Details/Actions
(Yellow)
Indicates a malfunction in:
The regenerative braking system;
The electronically controlled brake system; or
The parking brake system
Have the vehicle inspected by your Toyota dealer
immediately.
Warning light
Details/Actions
Indicates that the engine coolant temperature is exces-
sively high
Immediately stop the vehicle in a safe place.
Handling method (P.489)
-------------------------------------------------------------------------------------------------------------------------------------------------------------
451
8-2. Steps to take in an emergency
8
Whe
n tr
ouble
ar
ises
■
Hybrid system overheat warning light
*
(warning buzzer)
*
: This light illuminates on the multi-information display.
■
Charging system warning light
■
Low engine oil pressure warning light
*
(warning buzzer)
*
: This light illuminates on the multi-information display.
■
Malfunction indicator lamp (warning buzzer)
Warning light
Details/Actions
Indicates that the temperature of the hybrid system is
excessively high
Stop the vehicle in a safe place.
Handling method (P.489)
Warning light
Details/Actions
Indicates a malfunction in the vehicle’s charging system
Immediately stop the vehicle in a safe place and con-
tact your Toyota dealer.
Warning light
Details/Actions
Indicates that the engine oil pressure is excessively low
Immediately stop the vehicle in a safe place and con-
tact your Toyota dealer.
Warning light
Details/Actions
(U.S.A.)
or
(Canada)
Indicates a malfunction in:
The hybrid system;
The electronic engine control system;
The electronic throttle control system; or
The electronic hybrid transmission control system
Immediately stop the vehicle in a safe place and con-
tact your Toyota dealer.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
452
8-2. Steps to take in an emergency
■
SRS warning light (warning buzzer)
■
ABS warning light
■
Brake Override System warning light/Drive-Start Control
warning light
*
(warning buzzer)
Warning light
Details/Actions
Indicates a malfunction in:
The SRS airbag system;
The front passenger occupant classification system; or
The seat belt pretensioner system
Have the vehicle inspected by your Toyota dealer
immediately.
Warning light
Details/Actions
(U.S.A.)
or
(Canada)
Indicates a malfunction in:
The ABS; or
The brake assist system
Have the vehicle inspected by your Toyota dealer
immediately.
Warning light
Details/Actions
When a buzzer sounds:
Indicates a malfunction in:
The Brake Override System; or
The Drive-Start Control
Have the vehicle inspected by your Toyota dealer
immediately.
Indicates that the shift position was changed and
Drive-Start Control was operated while depressing the
accelerator pedal.
Momentarily release the accelerator pedal.
When a buzzer does not sound:
Indicates that the accelerator and brake pedals are being
depressed simultaneously, and the Brake Override System
is operating.
Release the accelerator pedal and depress the brake
pedal.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
453
8-2. Steps to take in an emergency
8
Whe
n tr
ouble
ar
ises
*
: This light illuminates on the multi-information display.
■
Electric power steering system warning light (warning
buzzer)
■
Low fuel level warning light
■
Driver’s and front passenger’s seat belt reminder light (warn-
ing buzzer)
*
*
: Driver’s seat belt warning buzzer:
The driver’s seat belt warning buzzer sounds to alert the driver that his or
her seat belt is not fastened. Once the power switch is turned to ON, the
buzzer sounds for 6 seconds. If the vehicle reaches a speed of 12 mph (20
km/h), the buzzer sounds once. If the seat belt is still unfastened after 24
seconds, the buzzer will sound intermittently for 6 seconds. Then, if the
seat belt is still unfastened, the buzzer will sound in a different tone for 90
more seconds.
Front passenger’s seat belt warning buzzer:
The front passenger’s seat belt warning buzzer sounds to alert the front
passenger that his or her seat belt is not fastened. The buzzer sounds once
Warning light
Details/Actions
(Red)
or
(Yellow)
Indicates a malfunction in the EPS (Electric Power Steer-
ing) system
Have the vehicle inspected by your Toyota dealer
immediately.
Warning light
Details/Actions
Indicates that remaining fuel is approximately 1.7 gal. (6.4 L
, 1.4 Imp. gal.) or less
Refuel the vehicle.
Warning light
Details/Actions
Warns the driver and/or front passenger to fasten their seat
belts
Fasten the seat belt.
If the front passenger’s seat is occupied, the front
passenger’s seat belt also needs to be fastened to
make the warning light (warning buzzer) turn off.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст