Toyota C-HR (2018 year). Instruction — part 25
385
6-3. Do-it-yourself maintenance
6
Mainten
■
Rear turn signal lights and rear side marker lights
Open the back door and
remove the cover.
To prevent damaging the vehi-
cle, wrap the flathead screw-
driver with a tape.
Remove the 2 screws and
pull the light unit toward the
rear of the vehicle to remove
it.
Turn the bulb base counter-
clockwise.
Rear turn signal lights
Rear side marker lights
Remove the light bulb.
Rear turn signal lights
Rear side marker lights
When installing the light bulb, install by conducting
and
with the directions reversed.
1
2
3
4
5
3
4
386
6-3. Do-it-yourself maintenance
Install the lamp assembly.
Align the guide (
) and pins
(
) on the lamp assembly with
the mounting when installing it.
Install the 2 screws.
Install the cover.
6
7
8
387
6-3. Do-it-yourself maintenance
6
Mainten
■
Back-up lights
Open the back door and
remove the cover.
To prevent damaging the vehi-
cle, wrap the flathead screw-
driver with a tape.
Turn the bulb base counter-
clockwise.
Remove the light bulb.
When installing, reverse the steps listed.
1
2
3
4
388
6-3. Do-it-yourself maintenance
■
License plate lights
Open the back door and
remove the cover.
To prevent damaging the vehi-
cle, wrap the flathead screw-
driver with a tape.
Turn the bulb base counter-
clockwise.
Remove the light bulb.
When installing, reverse the steps listed.
1
2
3
4
389
6-3. Do-it-yourself maintenance
6
Mainten
■
Side turn signal lights
Insert a flathead screwdriver
and release the claw for the
outside rear view mirror
cover.
To prevent damaging the vehi-
cle, wrap the flathead screw-
driver with a tape.
Release the cover claws
spanning over the entire
perimeter.
Release the claw of the bot-
tom part of the cover and
then remove the cover.
1
Claw
2
3
390
6-3. Do-it-yourself maintenance
Insert a flathead screwdriver
and remove the lens to the
outside.
Remove the socket from the
side turn signal light housing.
Remove the bulb.
Replace the bulb and install
the socket to the side turn
signal light housing.
Align the grooves of the socket
to the side turn signal light hous-
ing.
4
5
6
7
391
6-3. Do-it-yourself maintenance
6
Mainten
Install the lens.
Insert the claw of the lens.
Attach the lens.
Arrange the wire harness on the
back side of the lens.
Insert the claw of the cover.
Attach the claw on the bot-
tom part of the cover.
8
9
10
392
6-3. Do-it-yourself maintenance
Attach the cover claws span-
ning over the entire perime-
ter.
Finally, confirm that the outside
claw is securely fitted.
■
Replacing the following bulbs
If any of the lights listed below has burnt out, have it replaced by
your Toyota dealer.
● Parking lights/daytime running lights
● Stop/tail lights
● High mounted stoplight
● Outer mirror illumination (if equipped)
■
LED light bulbs
The following lights consist of a number of LEDs. If any of the LEDs burns
out, take your vehicle to your Toyota dealer to have the light replaced.
●
Parking lights/daytime running lights
●
Stop/tail lights
●
High mounted stoplight
●
Outer mirror illumination (if equipped)
■
Condensation build-up on the inside of the lens
Temporary condensation build-up on the inside of the headlight lens does not
indicate a malfunction.
Contact your Toyota dealer for more information in the following situations:
●
Large drops of water have built up on the inside of the lens.
●
Water has built up inside the headlight.
■
When replacing light bulbs
→P. 380
11
393
6-3. Do-it-yourself maintenance
6
Mainten
WARNING
■
Replacing light bulbs
●
Turn off the lights. Do not attempt to replace the bulb immediately after
turning off the lights.
The bulbs become very hot and may cause burns.
●
Do not touch the glass portion of the light bulb with bare hands. When it is
unavoidable to hold the glass portion, use and hold with a clean dry cloth
to avoid getting moisture and oils on the bulb.
Also, if the bulb is scratched or dropped, it may blow out or crack.
●
Fully install light bulbs and any parts used to secure them. Failure to do so
may result in heat damage, fire, or water entering the headlight unit. This
may damage the headlights or cause condensation to build up on the lens.
●
Do not attempt to repair or disassemble light bulbs, connectors, electric
circuits or component parts.
Doing so may result in death or serious injury due to electric shock.
■
To prevent damage or fire
●
Make sure bulbs are fully seated and locked.
●
Check the wattage of the bulb before installing to prevent heat damage.
395
7
When trouble arises
7-1. Essential information
Emergency flashers . . .. 396
If your vehicle has to be
stopped in an
emergency . . . . . .. 397
7-2. Steps to take in an
emergency
If your vehicle needs to
be towed . . . . . . . 399
If you think something is
wrong . . . . . . . .. 406
Fuel pump shut off
system . . . . . . . 407
If a warning light turns
on or a warning buzzer
sounds . . . . . . . 408
If a warning message is
displayed. . . . . . . 418
If you have a flat tire. . .. 423
If the engine will not
start. . . . . . . . . 434
If the electronic key
does not operate
properly (vehicles with a
smart key system). . ... 436
If the vehicle battery is
discharged . . . . . .. 439
If your vehicle
overheats . . . . . . 443
If the vehicle becomes
stuck . . . . . . . ... 446
396
Emergency flashers
Press the switch.
All the turn signal lights will flash.
To turn them off, press the switch
once again.
■
Emergency flashers
If the emergency flashers are used for a long time while the engine is not
operating, the battery may discharge.
The emergency flashers are used to warn other drivers when the
vehicle has to be stopped in the road due to a breakdown, etc.
397
7
Wh
en tro
If your vehicle has to be stopped in an
emergency
Steadily step on the brake pedal with both feet and firmly depress it.
Do not pump the brake pedal repeatedly as this will increase the effort
required to slow the vehicle.
Shift the shift lever to N.
If the shift lever is shifted to N
After slowing down, stop the vehicle in a safe place by the road.
Stop the engine.
If the shift lever cannot be shifted to N
Keep depressing the brake pedal with both feet to reduce vehicle
speed as much as possible.
Only in an emergency, such as if it becomes impossible to stop
the vehicle in the normal way, stop the vehicle using the follow-
ing procedure:
1
2
3
4
3
398
Vehicles without a smart key
system: Stop the engine by
turning the engine switch to the
“ACC” position.
Vehicles with a smart key sys-
tem: To stop the engine, press
and hold the engine switch for
2 consecutive seconds or more,
or press it briefly 3 times or
more in succession.
Stop the vehicle in a safe place by the road.
4
Press and hold for 2 seconds or
more, or press briefly 3 times or
more
4
WARNING
■
If the engine has to be turned off while driving
●
Power assist for the brakes and steering wheel will be lost, making the
brake pedal harder to depress and the steering wheel heavier to turn.
Decelerate as much as possible before turning off the engine.
●
Vehicles without a smart key system: Never attempt to remove the key, as
doing so will lock the steering wheel.
5
399
7-2. Steps to take in an emergency
7
Wh
en tro
If your vehicle needs to be towed
The following may indicate a problem with your transmission. Contact
your Toyota dealer or commercial towing service before towing.
● The engine is running but the vehicle does not move.
● The vehicle makes an abnormal sound.
If towing is necessary, we recommend having your vehicle
towed by your Toyota dealer or commercial towing service,
using a wheel-lift type truck or flatbed truck.
Use a safety chain system for all towing, and abide by all state/
provincial and local laws.
Situations when it is necessary to contact dealers before towing
400
7-2. Steps to take in an emergency
Do not tow with a sling-type truck
to prevent body damage.
Towing with a sling-type truck
Towing with a wheel-lift type truck
From the front
From the rear
Release the parking brake.
Use a towing dolly under the
front wheels.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст