Toyota RM06H0E engine. Manual — part 5
Special Tool
Lock
Special Tool
Cover
Special Tool
Raise Up
Special Tool
Special Tool
Insert Mark
Terminal
Retainer
Terminal Retainer
[Retainer at Full Lock Position]
Stopper
[Retainer at Temporary Lock Position]
Terminal
Retainer
B–21
TERMINAL AND CONNECTOR REPAIR–TERMINAL REPLACEMENT
37
Wire Harness Repair Manual
Type K (For Insulation Displacement Connector)
(1)
Separate Connector
Using a special tool, release the lock and separate the
connector into 2.
NOTICE:
Do not apply too muck force to the lock arm.
(2)
w/ Cover : Open Connector Cover
Using a special tool, release the lock and open the cover.
NOTICE:
Do not apply too much force to the lock arm.
Type L (For 0.64 Type Connector)
(1)
Using the special tool, raise the retainer up to the
temporary lock position.
HINT:
The needle insertion position varies according to
the connector’s shape (number of terminals, etc.), so
check the position before inserting it.
Good
Bad
Special Tool
Lock
Special
Tool
Special Tool
Lock
Special Tool
Lock Housing
Upper
Housing
TERMINAL AND CONNECTOR REPAIR–TERMINAL REPLACEMENT
B–22
38
Wire Harness Repair Manual
Type M (For 0.64 of Insulation Displacement Connector
(IDC) Type)
(1)
Remove the Lower Housing
Using a special tool, release the lock and remove the lower
housing.
NOTICE:
D
Do not apply too much force to the lock arm.
D
Mark the upper housing and lower housing to
prevent mistakes when putting them together.
(2)
Remove the Upper Housing
Using a special tool, release the lock and remove the upper
housing from the lock housing.
NOTICE:
D
Do not apply too much force to the lock arm.
D
Mark the upper housing and lower housing to
prevent mistakes when putting them together.
Good
Good
Bad
Bad
Tool Mark
Tool Mark
[Female]
[Male]
B–23
TERMINAL AND CONNECTOR REPAIR–TERMINAL REPLACEMENT
39
Wire Harness Repair Manual
Type N (For 0.64II Type Connector)
(1)
Insert the tool into the insertion position near the tool
mark and raise the terminal retainer up to the
temporary lock position using the tool.
Disengagement order
NOTICE:
D
Use a precision screwdriver (1.2mm) or special tool
when disengaging the terminal retainer.
D
Do not insert the tool into any position other than the
tool insertion positions. After disengaging the
terminal retainer, be sure to check that the terminal
retainer has not been deformed. If it has been
deformed, replace it with a new one.
D
Some connectors have 2 or more tool insertion
positions. When disengaging the terminal retainer
from these types of connectors, follow the
disengagement order shown in the illustration on
the left.
Jig Insertion Hole
TERMINAL AND CONNECTOR REPAIR–TERMINAL REPLACEMENT
B–24
40
Wire Harness Repair Manual
Type O (For 1.0III of KITCUT Type Connector)
(1)
Insert a jig horizontally into the jig insertion hole.
(2)
Push the jig in until it stops.
(3)
Pull out the wire in the direction indicated by the arrow
and remove the housing.
Locking Clip
Pull Out
Connector
Wire Harness
Terminal
Retainer
Locking
Clip
”Waterproof Type”
Special
Tool
B–25
TERMINAL AND CONNECTOR REPAIR–TERMINAL REPLACEMENT
41
Wire Harness Repair Manual
4.
Disconnect Terminal from Connector
(a)
Determine the primary locking system from the
charts.
1. Lock Located on terminal
2. Lock Located on connector
3. Method of entry and operation
(b)
Push the terminal gently into the connector and hold
it in this position.
(c)
Insert the special tool into the connector in the
direction shown in the chart.
(d)
Move the locking clip to the unlock position and hold
it there.
NOTE: Do not apply excessive force to the terminal.
Do not pry on the terminal with the special tool.
(e)
Carefully withdraw the terminal from the connector by
pulling the lead toward the rear of the connector.
NOTE: Do not use too much force. If the terminal
does not come out easily, repeat steps (a) through
(e).
Locking Clip
Terminal Retainer
”Non–Waterproof Type”
SST
Tool Hole
Terminal Lance
Stopper Portion
0.64 Type
Non–waterproof type TLC housing
Insert the tool from wire harness side
TERMINAL AND CONNECTOR REPAIR–TERMINAL REPLACEMENT
B–26
42
Wire Harness Repair Manual
(f)
Insert the SST into the connector in the direction
shown in the chart.
(g)
Insert the SST fully to the tool hole, and push the
terminal lance.
NOTICE:
D
The terminal has a lance shape, therefore, the
housing may be damaged and the terminal may get
stuck if forcibly pried by wires etc.
D
Insert the SST so that the stopper portion surface is
facing up.
(h)
Carefully withdraw the terminal from the connector by
pulling the lead toward the rear of the connector.
NOTICE:
Removal of the terminal from housing cavity will cause
damage to the wire seal section, deteriorating
waterproofing performance. Replace the connector
with a new one.
NOTICE:
Do not insert the special tool into the female terminal
box. If you do so, replace the terminal with the new one
whether the terminal is broken or not.
NOTICE:
As for Non–waterproof type TLC housing, insert the
special tool into the housing from wire harness side.
Tool Hole
Terminal Lance
Special
Tool
Special
Tool
Tool Hole
Special Tool
Terminal
Lance
Special Tool
0.64 Type
B–27
TERMINAL AND CONNECTOR REPAIR–TERMINAL REPLACEMENT
43
Wire Harness Repair Manual
Insulation Displacement Connector Type
(a)
Using a special tool, push the terminal lance from the
tool hole.
(b)
Carefully withdraw the terminal from the connector by
pulling the lead toward the rear of the connector.
NOTICE:
D
Do not use too much force. If the terminal does not
come out easily, repeat step (a).
D
Always change the wire with the repair wire, in
accordance with step3.
primary
lock
Pull Out Terminal
While Pushing
TERMINAL AND CONNECTOR REPAIR–TERMINAL REPLACEMENT
B–28
44
Wire Harness Repair Manual
1.0III of KITCUT Type Connector
(a)
Remove Female Terminal
(1)
Insert the jig tip at an angle, as shown in the
illustration on the left.
(2)
Move the jig in the direction indicated by the arrow to
push and release the primary lock.
(3)
Pull out the terminal in the direction indicated by the
arrow and detach it.
NOTICE:
D
Do not remove and reinstall the same terminal more
than 3 times.
D
If the terminal is deformed at all, dispose of it.
D
Do not apply too much force when releasing the
primary lock.
D
Do not apply too much force when pulling out the
terminal. If the terminal does not come out easily,
repeat steps (1) to (3).
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст