Toyota Tundra. Manual — part 2582
Fig. 87: Identifying Floor Wire (Center Airbag Sensor - Side Airbag Sensor LH)
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
NG: REPLACE FLOOR WIRE
OK: Go to next step
15. CHECK SIDE AIRBAG SENSOR LH
a. Interchange the side airbag sensor RH with LH and connect the connectors to them.
b. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
c. Turn the ignition switch ON, and wait for at least 60 seconds.
d. Clear the DTCs stored in the memory (see DTC CHECK/CLEAR ).
e. Turn the ignition switch OFF.
f. Turn the ignition switch ON, and wait for at least 60 seconds.
g. Check for DTCs (see DTC CHECK/CLEAR ).
Result
RESULT TABLE
HINT:
Codes other than DTC B1630 and B1635 maybe output at this time, but they are not related to this
check.
h. Turn the ignition switch OFF.
i. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
j. Return the side airbag sensor RH and LH to their original positions and connect the connectors to
Result
Proceed to
DTC B1630 and B1635 are not output
A
DTC B1635 is output (for Double Cab)
B
DTC B1635 is output (for CrewMax)
C
DTC B1630 is output
D
2009 Toyota Tundra
2009 RESTRAINTS Supplemental Restraint System - Tundra
them.
Fig. 88: Identifying Side Airbag Sensor LH
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
A: USE SIMULATION METHOD TO CHECK (See DIAGNOSIS SYSTEM )
B: REPLACE SIDE AIRBAG SENSOR LH (See SIDE AIRBAG SENSOR (for Double Cab) )
C: REPLACE SIDE AIRBAG SENSOR LH (See SIDE AIRBAG SENSOR (for CrewMax) )
D: Go to next step
16. CHECK NO. 2 FLOOR WIRE (SIDE AIRBAG SENSOR LH - DOOR SIDE AIRBAG SENSOR
LH)
a. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
b. Turn the ignition switch ON.
c. Measure the voltage according to the value(s) in the table below.
Standard voltage
TESTER CONNECTION SPECIFIED CONDITION TABLE
d. Turn the ignition switch OFF.
e. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
f. Using a service wire, connect terminals 2 (BCL-) and 1 (BCL+) of connector B.
g. Measure the resistance according to the value(s) in the table below.
Standard Resistance
Tester Connection
Switch Condition Specified Condition
N11-1 (BCL-) - Body ground
Ignition switch ON
Below 1 V
N11-2 (BCL+) - Body ground
NOTE:
Do not forcibly insert a service wire into the terminals of the
connector when connecting the wire.
2009 Toyota Tundra
2009 RESTRAINTS Supplemental Restraint System - Tundra
TESTER CONNECTION SPECIFIED CONDITION TABLE
h. Disconnect the service wire from connector B.
i. Measure the resistance according to the value(s) in the table below.
Standard Resistance
TESTER CONNECTION SPECIFIED CONDITION TABLE
Fig. 89: Identifying No. 2 Floor Wire (Side Airbag Sensor LH - Door Side Airbag Sensor LH)
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
NG: Go to step 19
OK: Go to next step
17. CHECK FOR DTC
a. Connect the connectors to the side airbag sensor LH.
b. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
c. Turn the ignition switch ON, and wait for at least 60 seconds.
d. Clear the DTCs stored in the memory (see DTC CHECK/CLEAR ).
e. Turn the ignition switch OFF.
f. Turn the ignition switch ON, and wait for at least 60 seconds.
g. Check for DTCs (see DTC CHECK/CLEAR ).
OK: DTC B1630 is output.
Tester Connection
Condition Specified Condition
N11-1 (BCL-) - N11-2 (BCL+) Always
Below 1 ohms
Tester Connection
Condition Specified Condition
N11-1 (BCL-) - N11-2 (BCL+)
Always
1 Mohms or higher
N11-1 (BCL-) - Body ground
N11-2 (BCL+) - Body ground
2009 Toyota Tundra
2009 RESTRAINTS Supplemental Restraint System - Tundra
HINT:
Codes other than B1630 maybe output at this time, but they are not related to this check.
Result
RESULT TABLE
Fig. 90: Identifying Side Airbag Sensor LH
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
A: REPLACE DOOR SIDE AIRBAG SENSOR LH (See SIDE AIRBAG SENSOR (for Double
Cab) )
B: REPLACE DOOR SIDE AIRBAG SENSOR LH (See SIDE AIRBAG SENSOR (for CrewMax) )
C: Go to next step
18. CHECK SIDE AIRBAG SENSOR LH
a. Interchange the side airbag sensor RH with LH and connect the connectors to them.
b. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
c. Turn the ignition switch ON, and wait for at least 60 seconds.
d. Clear the DTCs stored in the memory (see DTC CHECK/CLEAR ).
e. Turn the ignition switch OFF.
f. Turn the ignition switch ON, and wait for at least 60 seconds.
g. Check for DTCs (see DTC CHECK/CLEAR ).
Result
Proceed to
NG (for Double Cab)
A
NG (for CrewMax)
B
OK
C
2009 Toyota Tundra
2009 RESTRAINTS Supplemental Restraint System - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст